Page 1 of 2 12 LastLast
Results 1 to 10 of 15
  1. #1
    Newcomer
    Join Date
    Jul 2005
    Location
    Boston
    Posts
    35

    Default Where to Mount Blinder M-20?

    I've been doing my research here, and I'm trying to figure out the best location to mount the M-20 on my Mazda Protege5. I'll be buying the laser shield and veil also (and I might be removing my foglights if I can find nice replacement grilles for those holes). It looks like I don't have a place to mount the transceivers that isn't behind the mesh. Where do you think I should put them? I was thinking maybe I should cut out two rectangles in the mesh for where the blinders would stick through in the highlighted areas below. Any ideas?




    Thanks!

  2. #2
    Administrator
    Join Date
    Nov 2004
    Location
    Morristown, Arizona, United States
    Posts
    3,300

    Default Install Video

    We just put a install video online on our site, check out this page:
    http://www.radarbusters.com/products...er/default.asp
    RadarBusters.com
    Motorcycle Mounts and Accessories
    Also Join me at -
    Twitter: RadarRoy
    Facebook: Roy Reyer

  3. #3
    Power User
    Join Date
    Feb 2005
    Location
    Garland, Texas
    Posts
    3,410

    Default

    I like the videos. Very cool.

    OUTRUN

  4. #4
    Good Citizen
    Join Date
    Jul 2005
    Posts
    98

    Default mesh

    I think it will work fine even behind the mesh.
    Your mesh doesn't seem to be too dense, and it will be protected.
    You could get even a better protection if you put two trans' in the small openings under the fog lights and a third trans' in the middle of the upper triangle near the "P" of protege.

    This is full coverage

  5. #5
    Old Timer
    Join Date
    Jan 2005
    Location
    Ohio
    Posts
    5,182

    Default Re: mesh

    Quote Originally Posted by subaru4wd
    I think it will work fine even behind the mesh.
    Your mesh doesn't seem to be too dense, and it will be protected.
    You could get even a better protection if you put two trans' in the small openings under the fog lights and a third trans' in the middle of the upper triangle near the "P" of protege.

    This is full coverage
    You do not want to mount it behind the mesh. If you do, and they aim at the headlight you're toast.

  6. #6
    Lead Foot
    Join Date
    Apr 2005
    Location
    Riverview, FL
    Posts
    439

    Default

    Your best bet would be mounting in the grill area above the license plate. If you put a blinder in each corner you would have good coverage on both your head lights and plate.

  7. #7
    Good Citizen
    Join Date
    Jul 2005
    Posts
    98

    Default aiming at lights

    I found out that driving with head lights turned on, does wonders on the LTI2020 !
    It makes ir harder for the laser-gun to get a reading.

  8. #8
    Lead Foot
    Join Date
    Apr 2005
    Location
    Riverview, FL
    Posts
    439

    Default Re: aiming at lights

    Quote Originally Posted by subaru4wd
    I found out that driving with head lights turned on, does wonders on the LTI2020 !
    It makes ir harder for the laser-gun to get a reading.
    How did you "Find this out?" because this is an untrue statement. It USED to on older laser guns, however it does not have an effect on them anymore.

  9. #9
    Good Citizen
    Join Date
    Jul 2005
    Posts
    98

    Default LTI2020

    As I wrote, I tried it for many times with different cars and turning lights on, has a bad effect on the LTI 2020 laser gun.
    I don't know about other guns.

  10. #10
    Newcomer
    Join Date
    Jul 2005
    Location
    Boston
    Posts
    35

    Default

    I think I'm going to be mounting them like they are above. I'm going to cut the mesh to allow the jammer heads to come through a bit, and I'm also thinking of moving them a little farther apart closer to the ends of the bottom grille) so that they cover my headlights and foglights better.

    -DaViper

 

 

Similar Threads

  1. Blinder M-25 Mount Behind Grille?
    By Ryfly in forum Blinder Laser Jammers
    Replies: 9
    Last Post: 04-21-2008, 07:35 PM
  2. Where to mount Blinder M-20
    By xXCriticizeXx in forum Blinder Laser Jammers
    Replies: 7
    Last Post: 10-07-2006, 06:27 PM
  3. Where to Mount the Blinder on a BMW Z4?
    By blinderz4 in forum Blinder Laser Jammers
    Replies: 10
    Last Post: 04-11-2006, 09:00 AM
  4. Where to mount Blinder on my car?
    By Ramses in forum Blinder Laser Jammers
    Replies: 40
    Last Post: 05-24-2005, 04:06 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •