Page 1 of 2 12 LastLast
Results 1 to 10 of 17
  1. #1

    Default New V1 displays P on startup

    Is it normal for a straight out of the box V1 to display P when starting ?

  2. #2
    Good Citizen
    Join Date
    Jul 2006
    Posts
    171

    Default

    Mine displays p-o-p when the "pop" feature is activated. A single "p" means that the program is changed from the default settings. You may want to check your programming. http://www.valentine1.com/lab/MikesLabRpt3.asp I don't know why your would have the programming changed from the factory, maybe yours was selected for spot quality checking.

  3. #3

    Default

    I'm fairly certain it is the single "p" and not "p o p". Is there a way to reset to factory defaults?

  4. #4
    Old Timer
    Join Date
    Jul 2005
    Location
    Great Lakes
    Posts
    6,540

    Default having

    Having pop turned on will show p,o,p during start up. Make sure unit is off, then as you are turning it on make sure you push the knob in and that will allow you to set your V1 the way you want it to be set.

  5. #5

    Default

    I know what the letters stand for, and how to program it. Is there a way to reset to defaults without going to each setting individually?

  6. #6
    Good Citizen
    Join Date
    Jul 2006
    Posts
    171

    Default

    Quote Originally Posted by chase123
    I know what the letters stand for, and how to program it. Is there a way to reset to defaults without going to each setting individually?
    Not that I know of. To restore defaults just program all arrows up on each step of the programming process, should take less than a minute.

  7. #7
    Radar Fanatic
    Join Date
    Feb 2006
    Location
    Bay City, Michigan
    Posts
    2,204

    Default

    The 1.8's AFAIK will not show a p if it has been changed from its original programming. The LED"s will lightup or not light up on the strength meter based on what selections are on or off.

    The 1.8 will on default display p-o-p following the startup sequence to show that POP is enabled. Might want to check again. I'm sure it is just pop on.

    For the next question - no way to factory reset - other than all arrows to the up position as stated earlier.

  8. #8

    Default

    Thanks. It is probably the "p o p" message that I am seeing then.

  9. #9
    Newcomer
    Join Date
    Apr 2006
    Posts
    22

    Default

    Why don't you go turn it off and back on and see if it says p o p when powering up

  10. #10
    Good Citizen
    Join Date
    Jul 2006
    Posts
    171

    Default

    Quote Originally Posted by bauzer71487
    The 1.8's AFAIK will not show a p if it has been changed from its original programming.
    My 3.826 is custom programmed with the pop off, it displays a single p on start up.

 

 

Similar Threads

  1. LI HP startup?
    By ktolon in forum Laser Interceptor
    Replies: 2
    Last Post: 04-26-2009, 04:49 PM
  2. V1 startup?
    By Truthalive7 in forum Valentine One
    Replies: 11
    Last Post: 09-29-2008, 04:02 PM
  3. V1 Displays E and also .......
    By Ace_Racer in forum Valentine One
    Replies: 10
    Last Post: 06-26-2008, 08:19 PM
  4. No self-test on startup.....?!
    By wrxecho in forum Blinder Laser Jammers
    Replies: 20
    Last Post: 02-21-2008, 03:14 PM
  5. Odd startup on x50
    By LookOut4TheYeti in forum Escort
    Replies: 10
    Last Post: 10-23-2006, 05:06 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •