PDA

View Full Version : LI and Speed Cheetah DIY



syrinx
11-01-2007, 04:11 PM
Hello.

I would like to buy a LI and connect it to Cheetah. I think you have a LPP with Cheetah and now you've installed a LI.

I would like to use a LI with a Cheetah wireless. I found the LI wiring diagram in the documentation pdf. With Cheetah and his wireless switch off, I think I need only connect the speaker to the Cheetah interface. The
LPP and ALG8 have a similar wiring diagram (speaker, on/off, led).

Do you think is possible to connect easily the LI with Cheetah? http://www.speedcheetah.com/scshop/page.php?&xPage=faqs_wireless_fitting_kits.html

interceptor
11-01-2007, 04:19 PM
difference is that LI have a speeker, and other BUZZER...

it is a huge difference, actualy "others" provide a + or - on buzzer port when alerting.. :-)

LI provides a audio signal on 2 blue wires and on CPU speeker, not only a simple + or -..

On the other hand, what you can use easy is MUTE output on LI... This port will provide - when alerting, if you connect that one to Cheetah port when usualy connect buzzer from "others" it just may work..

Maybe someone from Cheetah can elaborate on this..

anyhow if you doo this, there will be no voice or parking monitor alerts, but you will get same warning as from "others"..

I have NO experience with Cheetah so i can NOT tell you exactly, maybe Racer X or Aly can tell you more..

RacerX
11-01-2007, 05:12 PM
it doesn't work at this time. i tried a few things but didn't get it to interface.
myself and the Cheetah guys will get with Ivan on some things to see what we can do. i'll play with a few more things too.
i do have a "work around" for those on motorcycles though, so that you can hear the voice alerts through headphones/earpieces. :)
i won't be able to play with it until the weekend though, as I'm at SEMA this week.

syrinx
11-04-2007, 12:44 PM
[quote="RacerX"]i do have a "work around" for those on motorcycles though, so that you can hear the voice alerts through headphones/earpieces. :)[quote]

How works your work around? Withe the AUDIOnode?
Hope you will find a solution.
Thanks at all to handle this problem.

RacerX
11-04-2007, 01:23 PM
No, once the AUDIOnode works, everything else will automatically work, including the Vizalert and GPS mirror.

i actually took a simplistic approach, so that i could get audio, until an interface is done to also get the visuals through the Vizalert.
basically here's what I did:

First, I use an “extension cord” for the headphones (earpieces), to give me room, plus an easy disconnect point, since the end is near my seat when I get on and off the bike.
Then, on the LI, if you open the box up, there is a small jumper inside, move it over. This takes the audio from the internal speaker, and puts it in the 2 blue wires. Then I stripped off about an inch on each one. Then I wrapped them around 2 points on the plug end of the extension cord. This gave me sound to the earphones. Once I tested it and they worked, I wrapped them tightly with electrical tap to hold them.
With an older set I tried to cut the plug on some ear pierces and splice them. But the wires were so small in the earpiece cords it wouldn’t work right and the sound would cut in and out.
One hint when testing the volume, is to block one of the heads so you get the beeping on startup to test them. this gives you time to ensure you have the audio correct and adjusted.

It works great. i get the audio of the LI, plus i just put the V1 on the bike, so i get the Laser alerts visually through the Vizalert, should my temp connector come loose.

:)

happya$$
11-04-2007, 01:29 PM
No, once the AUDIOnode works, everything else will automatically work, including the Vizalert and GPS mirror.

i actually took a simplistic approach, so that i could get audio, until an interface is done to also get the visuals through the Vizalert.
basically here's what I did:

First, I use an “extension cord” for the headphones (earpieces), to give me room, plus an easy disconnect point, since the end is near my seat when I get on and off the bike.
Then, on the LI, if you open the box up, there is a small jumper inside, move it over. This takes the audio from the internal speaker, and puts it in the 2 blue wires. Then I stripped off about an inch on each one. Then I wrapped them around 2 points on the plug end of the extension cord. This gave me sound to the earphones. Once I tested it and they worked, I wrapped them tightly with electrical tap to hold them.
With an older set I tried to cut the plug on some ear pierces and splice them. But the wires were so small in the earpiece cords it wouldn’t work right and the sound would cut in and out.
One hint when testing the volume, is to block one of the heads so you get the beeping on startup to test them. this gives you time to ensure you have the audio correct and adjusted.

It works great. i get the audio of the LI, plus i just put the V1 on the bike, so i get the Laser alerts visually through the Vizalert, should my temp connector come loose.

:)


wow amazing :lol:

spankyaf
11-04-2007, 07:23 PM
Plonkers .... get a move on ... I'm living in a frickin police state

syrinx
11-05-2007, 03:56 PM
OK. Hope the Cheetah boys will find a solution soon.

A bout LI, do you know if we can lengthen the RJ45 cable of a sensor? Whare can we buy the cable?

Best regards.

syrinx
11-09-2007, 04:56 PM
About LI, do you know if we can lengthen the RJ45 cable of a sensor? Whare can we buy the cable?

It seems that RJ11.

Can we use a RJ11 right male to /female to lengthen the sensor's cable? The problem is for rear sensors.

RJ11 right male to /female like this:
http://www.cableuniverse.co.uk/catalog/index.php?main_page=product_info&products_id=55

interceptor
11-11-2007, 01:28 PM
as long as it is straight (NOT CROSSOVER) u can use it...

glider
11-11-2007, 02:47 PM
It seems that RJ11.

Can we use a RJ11 right male to /female to lengthen the sensor's cable? The problem is for rear sensors.

RJ11 right male to /female like this:
http://www.cableuniverse.co.uk/catalog/index.php?main_page=product_info&products_id=55

Be careful

usually ADSL cable have 4 leads, so RJ11 connectors have pin n. 1 and 6 empty. Often RJ11 connectors for phone or ADSL even have not contacts n.1 and 6 (RJ11 6P4C)

http://64.27.0.105/productlargeimages/9292.jpg

You need a RJ11 6P6C with ALL 6 contact and 6 lead flat cable, like this one:

http://64.27.0.105/productlargeimages/9392.jpg

spankyaf
11-11-2007, 08:56 PM
as long as it is straight (NOT CROSSOVER) u can use it...

It just hit me thats the perfect solution to being able to switch the unit from my car to bike without having to mess around with the firewall again.

Although I'm now an expert with a coat hangar and liquid soap :D

interceptor
11-12-2007, 04:59 AM
lol liquid soap always helps.. :-)

you could do that but make sure this FF connector is placed in a watherproof box... since it will be on the other side of firewall...

syrinx
11-12-2007, 01:42 PM
Ok thanks. at all.


Now have you tested a new solution for use LI with Cheetah?

interceptor
11-12-2007, 03:33 PM
i am making a interface for them now as we write, to make it easier and faster to "include" us to they offer...

i love the GPS RWM that i saw in Texas..

syrinx
11-12-2007, 11:46 PM
Super!


i love the GPS RWM that i saw in Texas..

Do you speak about the GPS smartnode?
here: http://www.speedcheetah.com/scshop/section.php?xSec=118

spankyaf
11-14-2007, 09:59 AM
i am making a interface for them now as we write, to make it easier and faster to "include" us to they offer...

i love the GPS RWM that i saw in Texas..

Very nice .... I guess its too soon to be in Spanky's sock for xmas but for next years riding season would be great 8)

allyoops
11-19-2007, 02:59 PM
Super!


i love the GPS RWM that i saw in Texas..

Do you speak about the GPS smartnode?
here: http://www.speedcheetah.com/scshop/section.php?xSec=118

Nope - the GPSmirror

here: http://www.speedcheetah.com/scshop/section.php?xSec=24

syrinx
11-20-2007, 01:37 PM
OK thanks.

About AUDIOnode (http://www.speedcheetahusa.com/cheetah_AUDIOnode.html), is it possible to know if an alert coming from the Bel STI or coming from the LI? I woud like to use this 2 units at the same time.

I can read this in the doc of AUDIOnode but I can't find more descriptions.


The Cheetah AUDIOnode will beep and flash during an alert. Different audio tones and different LEDs will display different alerts.

allyoops
11-21-2007, 03:41 AM
Syrinx,

The Audionode isn't designed work with the STi and I can't envisage the circumstances where you'd want it to do that anyway.

Can you explain to me what you're trying to achieve / the ideal set up that you're looking for? I can then explain how any of our products can help towards that.

syrinx
11-21-2007, 02:45 PM
Syrinx,

The Audionode isn't designed work with the STi and I can't envisage the circumstances where you'd want it to do that anyway.

Can you explain to me what you're trying to achieve / the ideal set up that you're looking for? I can then explain how any of our products can help towards that.

Ok. I would like to use at the same time a Bel STI and a LI (when Ivan will be ready). The STI detects doppler radars. The LI detects lidars. Both are connected wireless with Cheetah products. And I put the AUDIOnode inside the car to be warned about radars. Is it possible like this? (without GPSmirror which is expensive)
If yes, is it possible to use different warnings for doppler (STI) and lidar (LI)?

allyoops
11-22-2007, 06:16 AM
Where are you planning to put the STi?

allyoops
11-22-2007, 06:18 AM
Could an admin please split this into the Cheetah Section?

syrinx
11-23-2007, 05:11 PM
Ok. Here: http://www.radardetector.net/viewtopic.php?p=338410#338410