Hi
Can you mix HP and Standard LI heads on the same CPU?
I am looking at setting four heads up front two angled for the Poliscan cameras and two straight for laser hand held shots.
Thanks
Printable View
Hi
Can you mix HP and Standard LI heads on the same CPU?
I am looking at setting four heads up front two angled for the Poliscan cameras and two straight for laser hand held shots.
Thanks
Quote:
Originally Posted by madmurf
Yes, you may if you have a Generation 8 CPU.
Cliff
I was going to PM you to ask this Cliff, but I thought it would be good to post the answer here.. anyway my question is:
At what time (timewise, and version-wise) did LI switch to all slim heads instead of "regular" and "slim"?
Effective March 1, 2010, we eliminated the larger 8.7 sensor from The LI-USA Product Line completely. With the new Generation 8's enhanced receiver and detection capabilities, we can now fully exploit the smaller sensor in both the front and rear vehicle applications and at the same time allowing for easier and more stealthy installs due to their smaller foot print.Quote:
Originally Posted by kpatz
Cliff
Damn. You come out with the smaller heads NOW? LOL.Quote:
Originally Posted by Laser-InterceptorUSAEffective March 1, 2010, we eliminated the larger 8.7 sensor from The LI-USA Product Line completely. With the new Generation 8's enhanced receiver and detection capabilities, we can now fully exploit the smaller sensor in both the front and rear vehicle applications and at the same time allowing for easier and more stealthy installs due to their smaller foot print.Quote:
Originally Posted by kpatz
Cliff
Over a year ago. You have the new smaller sensors!
Cliff
It would help if I actually read that whole post. Hahaha! Was gonna say, the heads are small enough as it is.Quote:
Originally Posted by Laser-InterceptorUSA
No worries!
Cliff
Guess that means I don't have the slim heads... so next question, what's the size (depth) difference between the 8.7 regular heads and the 8.8 slim heads? If/when I upgrade I'll have to shim them so they aren't recessed in the grill.
13/16" vs 1 1/4"
Cliff
So a smidge under half an inch difference then? I'll need 1/2 inch shims if I upgrade my heads then, or completely re-engineer my in-grill mounting scheme...
Ok, So what changes have there been since 8.7.
Also, is there some way to be notified of firmware updates other than checking the web site?
Thanks
New Updates to address new LIDARS.
Because many change their email address often, the best way to see if an update is available is to add the update page to your favorites and check in once a month.
Cliff
What is in the update? I have to buy an old school connector so I can update.
It adds new LIDARS.
Cables are available at Radio Shack and on Amazon.
Cliff
Just an FYI to everyone. The new firmware 8.15 is out.
Generation 8 CPU Firmware Released 12 April 2014 Ver. 8.15
https://www.laser-interceptorusa.com/downloads
Yes it is.
However,depending on where you drive in the USA...you may still not have 100% protection from some Lidar models.Just an FYI to let you know.
Yes it is.
However,depending on where you drive in the USA...you may still not have 100% protection from some Lidar models.Just an FYI to let you know.
Really? Why?Quote:
Originally Posted by RedRocket
Really? Why?Quote:
Originally Posted by RedRocket
Have you read any other post about this?
Yes - Really !Quote:
Originally Posted by EricTheRedReally? Why?Quote:
Originally Posted by RedRocket
Because I was present when it was tested @ a Shooters Meet.
Yes - Really !Quote:
Really? Why?
When what was tested? Why the secrets? Spill the beans or share a linkQuote:
Because I was present when it was tested @ a Shooters Meet.
^ - Well,you did post this didn't you ?Quote:
Originally Posted by EricTheRed
When the point you made above was tested,why would I make a comment off Topic on something unrelated to what you brought up?Quote:
Originally Posted by EricTheRed
There are no secrets about this!
I did spill the beans already. (Depending on where you drive,you may not be fully protected.)
Laser Interceptor firmware 8.15 does not jam the Stalker XLR. It also still does not detect the DragonEye Compact and a version of the DragonEye LIDAR (DALA). The firmware does improve performance against the Truspeed S.
Were these guns being Jammed in 8.14? Hopefully there will be more firmware updates coming.Quote:
Laser Interceptor firmware 8.15 does not jam the Stalker XLR. It also still does not detect the DragonEye Compact and a version of the DragonEye LIDAR (DALA). The firmware does improve performance against the Truspeed S.
NoQuote:
Originally Posted by EricTheRed
For anyone who wants to know; version 8.16A is out. No idea what improvements there are.
LI 8.16A fixed the PL3 bug-- then release for 8.18 is out.
Quote:
Originally Posted by BHRODEOAZ
Firmware 8.16: Stalker XLR v.2
Firmware 8.16A: Bug fix
Firmware 8.18: DragonEye Compact (not all versions). Doesn't work well. I don't recommend updating to this firmware.