Once you become familiar with all of the falses in your area you will become aware if an extra one shows up on the counter
Printable View
Once you become familiar with all of the falses in your area you will become aware if an extra one shows up on the counter
Yes the V1's added bogey tone is pretty distinct.Quote:
Originally Posted by Phillip559
it has saved me before. i run an rx65 in tech mode though.
Absolutely!Quote:
Originally Posted by hockey005
I think I'm going to switch over from SpecDisplay (showing the frequency) to Expert Mode (showing multiple threats) in my 9500i this week. I notice sometimes while in SpecDisplay the 9500i will bounce and show the frequencies of multiple sources but not always. Today in fact there were two separate occasions where I was alerted, reduced speed and had no problems, but had I been running in Expert Mode would have had more information at my fingertips rather than surprises. Being surprised by an additional unexpected LEO operating in the vicinity isn't like opening a christmas present kind of surprise.
I've enjoyed using SpecDisplay, it was certainly interesting to know more about what specific types of radar is in use in my area, but clearly its time to move on. Both incidents for me today could have potentially been tickets.
First incident I was coming into a highway construction zone. Speed was reduced to 55 MPH and I was already in the reduced zone, but could see the flagger and a speed sign further up the road so I hadn't reduced my speed yet, began to pick up the K band alert from the speed sign, and still didn't slow down yet (wasn't in the actual construction zone yet, just the speed restricted area prior to coming into it). Suddenly went from a K band alert to Ka in the display, yet the voice alert ("***** in the box" I like to call her) from the detector I swear (could have been mistaken) announced "K band" even though a Ka freq was being shown in the display.
Well, minimal required experience told me right away there was a CHP somewhere there, pretty common in construction zones, so it was immediately obvious I was up against the K band speed sign and a Ka CO LEO likely parked on the roadside mixed in by the construction workers vehicles. This scenario created a situation I can't say I appreciated from my detector. The K band sign was clearly the closer (technical) threat, yet the Ka band alert was trumping this in both the display and in the alert tone. Even when I was slowed down now and immediately in front of the K band sign I was still only getting the single ping Ka band alert tone. Had that been an actual LEO running K band he could have technically had me if you toss experience out the window and went only on what the alert tone was telling you. Granted, experience clearly had to play a role here, I knew I was on a California State Highway and only Ka band was ever in actual use there, but still didn't like how Ka was trumping the more immediate threat, legitimate or otherwise, it was after all technically actual K band police type radar used on that sign. Expert mode which in the 9500i shows both the multiple threats as well as the signal strength of each clearly would have made a difference for me here. It would have taken out the trump factor and displayed the K band threat as the closer (stronger) signal.
The second incident happened just a little further up the road as I entered into city limits. There's a permanently installed speed sign here that I'm aware of. I don't have it locked out because as I approach this town I know its there and like to check my range to it just for fun, normally though, this would be the type of useless alert I would have locked out. Last time I drove into this town about a week ago I noticed this sign was malfunctioning, speed displayed was all over the place and I wasn't picking up any alert from it, I noticed today though they had since fixed it and it was back into proper operation, complete with its normal 1.5 mile range K band alert on approach even though it doesn't show your speed till your within about 200 feet of it. It's kind of a funny sign, they have these flashing white strobe lights on it that go off if your speeding. Its like they purposely want to trick people into thinking its a speed camera because the strobe light looks like a camera flash, even though it isn't.
Its a small town, I drive in it often and have seen the local city PD but never detected radar from them, CHP runs Ka band there so I assumed the only threat to be Ka band, and that fixed K band pretend speed camera (no real threat).
So I'm setting still on my way back in the McDonalds drive through waiting for my food. This K band speed sign is about 1/4 mile up the road facing me. Auto Mode on the 9500i working well and even though I'm in range of the sign I hear no alerts from it because I'm at 0 MPH. My focus wasn't on the sign but instead the nice butt of the girl working the drive though window, actually enjoying the delay in my food preparation just due to this fact.
All of a sudden and out of no where my detector goes off into a full blast K band alert, and I'm like WTF? I'm at 0 MPH with Auto Mode enabled, I shouldn't be getting a K band alert at all? I look across the street at that stupid speed sign and sure enough, setting parked directly under it is a Susanville CA city LEO hitting a car with K band IO. Ahhhhh, you sneaky little prick you. By not having that sign locked out and not being in Expert Mode, he could have easily had me driving up into that situation. I knew the sign was there, I knew it was K band, all I would have seen was his IO mixed in with the signal from the sign and would have been in complete ignore mode to the alert, he would of had me for sure.
So I have now been able to at least confirm, when in 9500i Auto Mode, even at 0 MPH, if a sudden imposing X or K band threat turns up, you get the alert, that's comforting to know. Otherwise slow speed automaticly filters these alerts out and do not display. That's well thought out I have to admit in Escorts thinking and ability to very effectively filter out a typical false while still alerting to an actual threat, it impressed me.
Got my food, LEO had a customer and his radar back to off so I made a point of driving back up the road and locking out that speed sign now. I'll know when I approach that area now if I get a K band alert it won;t be coming from the now locked out sign, but instead from that LEO there playing his tricks. Like I said, I'm also switching over to Expert Mode, this way, even if the sign drifts out of my locked out block I'll be alerted to the multiple threats.
It's kind of interesting when I initially read this post the other day I almost posted to it thinking Expert Mode wasn't that big of a deal, you get an alert, you slow down, doesn't matter if its just one or ten threats. Clearly after two almost back to back separate accounts today though I can easily now see the absolute advantages to being alerted to multiple threats. This feature in any detector gets added to my own list of must have items in any detector I would ever consider using, its right up there on my list with the need for GPS lockout capabilities. Maybe not as high on the list as GPS locking out capabilities (which would have given me an extra blanket of security in both these situations had I of locked out the speed signs), but certainly a must have feature on the list. I rate GPS lockout abilities higher though because its a feature I use extensively, as opposed to displaying multiple threats which would only come in handy once in a while, still though, none the less, a must have feature for sure.
Spec Display Mode is critical on the 9500i when using "TrueLock" to lock out door openers and the like. The most useful for recording the non threating alert.Quote:
Originally Posted by Esoterica
Once I verified and locked out door openers on my commute I then switched to Expert Mode
Expert Mode is what I always use on my X50.
I confirmed this a year ago when I had my 9500i. Just drive up slowly to any door opener in Auto Mode. When you are within 30 feet or so of the door opener, the 9500i will alert fully.Quote:
Originally Posted by Esoterica
X2, I use Expert mode exclusively, besides multiple alerts i find it to be more stealthy (not blaring bright when alerted).Quote:
Originally Posted by nascar
I use speck mode to verify local LEO's radar and near by falses then switch back to Expert mode always.
I also use ExpertMode, near exclusively.
It's a very nifty tool.
However, I'd like to caution everyone, don't trust it, blindly, either.
"Ghosting" as well as "Merging" are both still very real phenomenons with the 9500i (as it is with other detectors capable of indicating the "number" of threats).
Although one's familiarity with the driving route and enforcement procedures/hardware can tremendously decrease the potential for such concerns to become a true liability, it will serve well for us to remember these issues when we travel in "unknown" areas.
Don't get me wrong - I like ExpertMode, a lot. :) Sure, I would like to see it improved a bit (allow for the end-user to be able to select how many bands, of what frequencies, are displayed, etc.), but as an aid in terms of increasing the functionality of my last two Escort detectors, I think it's wonderful.
It's just that I also feel it is very important to know the limitations of one's tools/instruments, too.
:)
I have pretty much everything already locked out in my areas, I never relied on SpecDisplay for locking anything out, instead I make sure I can drive by the area a good three times at different times and days and always reproduce the same false before locking it out. I don;t buy into the claims that you can determine actual police radar by just the freq that's being displayed, I see actual police radar all over the freq within the band despite the claims that these are somewhat fixed.Quote:
Originally Posted by nascar
I also am fortunate in most my primary lockout areas there is never any X or K band in use, its exclusively Ka. The only places I see K band in use are some small towns which typically have little to no false sources to even lock out.
I've avoided using ExpertMode just because I didn't like the condensed display size that goes with it, but I'll be trying it out starting today to see if I can't just get use to it. Its still likely good advice to run SpecDisplay for a couple months first to get to better know your area and what's being used, just like you should likely first begin running in the default display mode to get use to how the detector responds to threats in your area by being able to physically see the strength meter.
I'm not overly worried about this problem, at least it defaults to safe and you at least do get the alert when present. It would be nice if there was a way to make any detector that displays multiple threats not ghost or merge, but due to the nature of just how radar signals operate its pretty much always going to be an impossible accomplishment to achieve with 100% effectiveness.Quote:
Originally Posted by TSi+WRX