PDA

View Full Version : Highly technical questions on Laser Guns and Jammers



Fedds
06-30-2005, 09:39 AM
All,
I'm an electrical engineer and after my last ticket I decided it's time to design my own laser jammer as a project. I have some techincal questions though that I hope some of the knowledgeble people here can answer. Thanks in advance. Also, I doubt I'm going to try and sell anything I make. I'll make the schematic and parts list public if we get something that works

1) What is this "punchthrough" that everyone talks about. Is this the point at which the laser guns signal is strong enough to get a reading?

2) What is the power rating of the laser diode in the Lidar gun (it would be great if you could also provide the model of the gun).

3) What jammers on the market use a laser diode? What jammers use a IR LED array?

4)Does anyone know the profile or signal that the jammer is trying to replicate? I read you want a a few nano second pulse repeated at 1 kHz. Sound right or way off (I'm going to put adjustments on the prototype for frequency and duration, but I need to be in the ball park to start the design)

That seems like a good starting point.

Thanks again,
Fedds

brick
06-30-2005, 09:50 AM
1) "Punch Through" is the point at which a jammer ceases to be effective as the vehicle approaches the lidar gun. In general, jammers start working at around 1000ft but can't keep the car cloaked at very short range (~300ft and in.)

2) Don't know...might be able to derive that from the specifications of a LIDAR gun.

3) The Lidatek uses a laser diode and I think that everybody else uses an array over-driven LEDs like you were talking about in the other thread.

4) Not sure. I read somewhere that the pulse rates vary between 100 and 400Hz depending on the gun. Each manufacturer is different and some, like the Laser Atlanta, can even switch between different patterns in an attempt to confuse detectors and jammers. (And it works!)

T-T
06-30-2005, 10:13 AM
3) I know actually Lidatek LE-30 and Target LT-400 with laser diodes. All other products (eg. Blinder) use IR LED as I know.

JTW
06-30-2005, 10:15 AM
3) I know actually Lidatek LE-30 and Target LT-400 with laser diodes. All other products (eg. Blinder) use IR LED as I know.

The Antilaser AL6 use laser diodes.

Fedds
06-30-2005, 10:54 AM
Hmmm, a gun that varies it's frequency?!?! That's just plain mean. Up till now I was pretty sure that my unit would continually jam and would not try to detect. Now though I have to rethink this.

See, most of the LED's I've seen might operate at 1W (and you can over drive them some). I was looking at a 25-45W laser diode (still need to make sure it's not going to cause eye damage to bystanders). At any rate, that amount of energy being emitted all the time is going to really make any detection in the vehicle difficult. I could you some detection scheme, then alter my jamming pattern to the incoming frequency with some phase shifting to really mess with the gun.

How about this, what size fuse does the blinder and Lidatek units use? The diodes I was planning on using can pull up to 25 amps a piece! (for a very short amount of time...30nS...needs alot of power filtering just so you radio will operate near this beast:)

brick
06-30-2005, 11:26 AM
Sorry, I didn't mean variable on-the-fly. (I worded that badly.) I mean it has two modes. One is the normal pulsing and the other is bursts of two. It works because most detectors and jammers will only alert if they see a burst of three or more. The V1 doesn't need that, for whatever reason, so it picks up the "stealth mode" just fine.

thestaton
06-30-2005, 11:30 AM
JTW: Do you have access to any of the gun manufactures spec's he could see? I know alot of there sites offer the info if you are registered, but us common folk, well they wont let us register :)

JTW
06-30-2005, 11:56 AM
JTW: Do you have access to any of the gun manufactures spec's he could see? I know alot of there sites offer the info if you are registered, but us common folk, well they wont let us register :)

This info is kept proprietary. You're talking about pulse train patterns right? I don't know the specifics and if I did know it that would destroy all bridges on this side of the fence I'm on. I can test laser jammers and such, but I can't give company secrets.

laserblaster
06-30-2005, 01:43 PM
you dont need the manufacturers specs all you need is a laser gun and a lab and equipment to test it out!

this is all what stealth microsystems do!

but on saying that all rd and jammer manufacturers have theses specs!
otherwise their products wouldnt work..

if your like mike valentine it shouldnt take too long to make one!

xwarp
07-01-2005, 04:15 PM
this and an ir sensor would do the job!

http://www.astglobal.com/ebay/05-27/dtb1382.JPG

compu44
07-01-2005, 05:15 PM
The problem with a contuniuosly transmitting jammer would be that it would presumably show a "jammed" indicator on the laser guns, and it would also set off all the laser detectors around you, which isn't very nice.

crazyVOLVOrob
07-01-2005, 05:17 PM
^Also would burn out quickly

markos
07-03-2005, 05:17 PM
Im with you fedds -I have been trying to get info to design my own stuff
It seems most LIDAR guns are putting out 904nm @ 100 to 300 pps
I have made a mini LIDAR `simulator` that sets off my bel945 detector
I will sweep it to see the freq range. -see my other posts here..





All,
I'm an electrical engineer and after my last ticket I decided it's time to design my own laser jammer as a project. I have some techincal questions though that I hope some of the knowledgeble people here can answer. Thanks in advance. Also, I doubt I'm going to try and sell anything I make. I'll make the schematic and parts list public if we get something that works

1) What is this "punchthrough" that everyone talks about. Is this the point at which the laser guns signal is strong enough to get a reading?

2) What is the power rating of the laser diode in the Lidar gun (it would be great if you could also provide the model of the gun).

3) What jammers on the market use a laser diode? What jammers use a IR LED array?

4)Does anyone know the profile or signal that the jammer is trying to replicate? I read you want a a few nano second pulse repeated at 1 kHz. Sound right or way off (I'm going to put adjustments on the prototype for frequency and duration, but I need to be in the ball park to start the design)

That seems like a good starting point.

Thanks again,
Fedds

Vonkie
12-17-2005, 05:37 AM
All,
I'll make the schematic and parts list public if we get something that works


So did anything transpire from this exercise? I also intend to build a detector/jammer and is currently scanning the scene for what can be done.
Any success??

jimbonzzz
12-17-2005, 08:13 AM
All,
I'll make the schematic and parts list public if we get something that works


So did anything transpire from this exercise? I also intend to build a detector/jammer and is currently scanning the scene for what can be done.
Any success??

Check this thread, might give you some ideas:
http://www.radardetector.net/viewtopic.php?t=3085

Vonkie
12-19-2005, 08:10 AM
Any reason why the jamming circuit of the the old Blinder M-6 wont work if the clock frequency is increased to 10 MHz, some pulse shaping done to vary the pulse length from 10 -20 nSec continuously and also vary the pulse rate continuously between between 100 -300 Hz randomly. If the transmitting LED's are in the range of 2 - 3 watt it should bamboozle any LIDAR gun???? :(

jimbonzzz
12-19-2005, 09:28 AM
Any reason why the jamming circuit of the the old Blinder M-6 wont work if the clock frequency is increased to 10 MHz, some pulse shaping done to vary the pulse length from 10 -20 nSec continuously and also vary the pulse rate continuously between between 100 -300 Hz randomly. If the transmitting LED's are in the range of 2 - 3 watt it should bamboozle any LIDAR gun???? :(

To produce a pulse that is 10-20ns in duration, as far as I know LEDs cannot be used like in the Blinder M-6. They will not fully transition from "off" to "on" in 10-20ns, in fact the "rise time" of many LEDs is more than ten times that.

And with most guns (except for maybe the Jenoptik LaserPatrol) pulsing between 100-300 Hz randomly isn't going to jam much of anything, except by lots of luck. To jam most laser guns, there is a VERY small window where it must see a pulse. This is AFTER the laser gun sends out a pulse, but BEFORE it sees that pulse reflected back. So, you basically have the "time of flight" of the pulse for the laser gun to receve a jamming pulse.

The only real way to jam effectively without corellating outgoing pulses to incoming pulses, is to jam the way the old LE-10 did. When the laser was detected, they sent out pulses at a very high frequency, probably around 2 MHz. The idea being, that no matter what, the laser gun would always receive at least one jamming pulse before receivong it's own reflected pulse (@ 2 Mhz this would work down to 250 feet from the gun). But as the vehicle gets closer to the gun, the pulse's "time of flight" gets shorter, so a higher constant frequency is necessary for consistent jamming. For example, to consistently jam within 125 feet of the gun, the pulse frequency would need to be doubled to 4 MHz.

LEDs can't reproduce pulses at such a high frequency. This is also beyond the specs of laser diodes, which are normally rated in the KHz range. But Lidatek found that laser diodes would indeed work at high frequency (2 MHz etc) for short periods of time, without burning out. So the LE-10 only jammed for a short period, to prevent destroying the laser diodes.

This method is arguably a very good way to do it, since such a jammer should effectively jam all guns and would not need updating as new guns are produced.

Jim

Vonkie
12-19-2005, 09:54 AM
Thanks for the info Jim. I'm a bit confused with the laser diode performance. For the SPL PL85 the datasheet states a Rise/Fall time of 1 nSec. Am I missing something?? Also they claim a performance rate of of 100 nSec pulses @ 1 KHz at a current of 10A. Not sure how they get rid of the heat :?

So it appears that running 10 - 20 ns pulses is a possibility??

jimbonzzz
12-19-2005, 10:13 AM
Thanks for the info Jim. I'm a bit confused with the laser diode performance. For the SPL PL85 the datasheet states a Rise/Fall time of 1 nSec. Am I missing something?? Also they claim a performance rate of of 100 nSec pulses @ 1 KHz at a current of 10A. Not sure how they get rid of the heat :?

So it appears that running 10 - 20 ns pulses is a possibility??

No Problem. :wink:
You're not missing anything, all of that sounds correct to me.

Blinder, Zr3, etc use LEDs to jam, while others like Lidatek Antilaser etc use laser diodes. Interestingly since the LED jammers do OK, it seems that a pulse duration that is too long is not a problem, the guns must detect the leading edge.

Jim

Vonkie
12-19-2005, 10:39 AM
Mmmm.... I think the trick is in the duty cycle - 0.1%.
This gives a mark/space ratio of 1/1000. Thus if one use a pulse length say of 20 ns then the total period for the cycle is 0.02ms which corresponds to 50kHz

30 ns pulse would be 33 kHz. ( :idea: - bandwidth of some jammer I've seen :D )

So if one utilises a pulse frequency (pps) of 1kHz then you can virtually use any pulse length from 10 - 30 ns continuously without a problem :P

The concept that you need to pulse at very high frequencies in order to jam at close distances is a bit of a myth in my opinion. The reason being that if the lidar gun starts to pulse @ say 300 pps the detector will sense it and immediately the jammer will start to reply @ say 1000 pps. This transmission continues until the detector does not sense the lidar gun any longer. As long as the jammer replies at a rate faster than the lidar gun then the distance between the car and the lidar gun is really irrelavant

Breakthrough is really a matter of how powerful the jammer laser is. If the Lidar gun is so much more powerful than the jammer so that the reflected lidar signal overpowers the jammer signal then the filters in the lidar gun will be able to identify its own signal and the jammer signal will be rejected as noise. So the moral of the story is that the jammer signal needs to be powerful so as to "cloak" the car at all times.

Do you agree??

Vonkie
12-20-2005, 01:49 AM
I see what you mean with the window Jim...... :idea:

Pulsing @ 1kHz will give a pulse spacing of 1 mS. The total flight time for the pulse between the gun and the car can vary from say 300 - 1800 nS depending on the distance and your pulse rate needs to beat this.

However, measurements are not taken with a single pulse only. If say 10 pulses were used by the gun to get a solution it will actually receive say 30 pulses if you were transmitting at 3x its rate.But they will still be spaced way off from the retuned pulse to make any difference. :cry:

Mmmm...now I understand the diode overheating dilemma :oops:

What is the life expectancy of the diodes in the commercial jammers???

What is the closest distance a lidar gun can measure at??

Vonkie
12-24-2005, 01:20 AM
To get around the pulse frequency problem it would be ideal to use a CW laser diode modulated (TTL) say to 2 MHz. They do not seem to be easily available and those that are, very expensive. See example HERE (http://qphotonics.com/product.php?productid=21&cat=10)

Anybody played with this concept??? :?

jimbonzzz
12-24-2005, 02:04 AM
I think those could potentially work to get around the frequency issue for a constant-pulse jammer, but these would also be much lower power than the pulsed variety which are 50W peak. You can get 100mw out of LEDs, and some jammers (such as Blinder) use 8 of them per jammer head.

So I think if one could somehow overcome the cost of using multiple CW laser diodes, it could be a solution...

Jim

Vonkie
12-24-2005, 02:45 AM
The snag is that if one is to go for a constant pulse version (easiest to build for the home constructor) then all LED's etc basically fall by the wayside. The frequency being the problem. If an "intelligent" receiver is used which can analyze the incoming signals and then pulse accoringly to jam then all these problems disappear. But for the home constructor this becomes expensive......

Just surprised that nobody on the forum seem to have played around with this, or maybe they are just keeping it to themselves... :(

1100xx
12-26-2005, 03:55 PM
Any reason why the jamming circuit of the the old Blinder M-6 wont work if the clock frequency is increased to 10 MHz, some pulse shaping done to vary the pulse length from 10 -20 nSec continuously and also vary the pulse rate continuously between between 100 -300 Hz randomly. If the transmitting LED's are in the range of 2 - 3 watt it should bamboozle any LIDAR gun???? :(

To produce a pulse that is 10-20ns in duration, as far as I know LEDs cannot be used like in the Blinder M-6. They will not fully transition from "off" to "on" in 10-20ns, in fact the "rise time" of many LEDs is more than ten times that.

And with most guns (except for maybe the Jenoptik LaserPatrol) pulsing between 100-300 Hz randomly isn't going to jam much of anything, except by lots of luck. To jam most laser guns, there is a VERY small window where it must see a pulse. This is AFTER the laser gun sends out a pulse, but BEFORE it sees that pulse reflected back. So, you basically have the "time of flight" of the pulse for the laser gun to receve a jamming pulse.

The only real way to jam effectively without corellating outgoing pulses to incoming pulses, is to jam the way the old LE-10 did. When the laser was detected, they sent out pulses at a very high frequency, probably around 2 MHz. The idea being, that no matter what, the laser gun would always receive at least one jamming pulse before receivong it's own reflected pulse (@ 2 Mhz this would work down to 250 feet from the gun). But as the vehicle gets closer to the gun, the pulse's "time of flight" gets shorter, so a higher constant frequency is necessary for consistent jamming. For example, to consistently jam within 125 feet of the gun, the pulse frequency would need to be doubled to 4 MHz.

LEDs can't reproduce pulses at such a high frequency. This is also beyond the specs of laser diodes, which are normally rated in the KHz range. But Lidatek found that laser diodes would indeed work at high frequency (2 MHz etc) for short periods of time, without burning out. So the LE-10 only jammed for a short period, to prevent destroying the laser diodes.

This method is arguably a very good way to do it, since such a jammer should effectively jam all guns and would not need updating as new guns are produced.

Jim


Hallo, I I have one inquiry. Why is necessary so that pulse from jammer was receive before incident to pulse choke off car ? is yet some that is of first, responsible position so as to them has been receive in sensitive windows lidar more'n one self-or with mislead? apologize for my bad English language

Pavel

jimbonzzz
12-26-2005, 04:26 PM
Hallo, I I have one inquiry. Why is necessary so that pulse from jammer was receive before incident to pulse choke off car ? is yet some that is of first, responsible position so as to them has been receive in sensitive windows lidar more'n one self-or with mislead? apologize for my bad English language

In general, the laser gun only accepts the first pulse received after a pulse is transmitted. So the laser gun must receive a jamming pulse in that time period, in order for it to be seen by the gun as the reflected pulse off of the vehicle.

Jim

1100xx
12-27-2005, 02:20 AM
Jimbonzz:In principle jamming is such that jammer must receive jamming pulse before return self pulse, but in every measure cycle has to be pulse in quite a different point (of course always before return self pulse)than in previous cycle? that is why when is for LIDAR distance to car every time diametrically diverse show display ????
TX Paul

Vonkie
02-12-2006, 07:53 AM
The question posed above is actually a very contentious one. If single pulse jamming is going to be used the position of that jamming pulse is vital. It could actually make matters worse for you....... :?

For example, the jammer only receives the pulse, it does not know how far the LIDAR is from it. The TOF from the car to the gun can be anything say from 150ns (50m) to 1800ns (600m). To prevent coverage over such a range more than one return pulse must be transmitted, or am I wrong???

Makes me think that the story of these single pulse intelligent jammers is a bit of hogwash. :shock:

jimbonzzz
02-12-2006, 08:06 AM
The jammer continues to receive pulses from the laser gun, and measures between them. That way, it can predict when the next pulse will arrive from the gun. The jammer can then send a jamming pulse slightly before the next pulse arrives from the gun, but also uses random delays in the timing so that the gun never sees consistent pulses with which to calculate a speed.

Vonkie
02-12-2006, 01:04 PM
In that case how does it handle the wide band in which it can transmit??

It is fine for the gun to calculate the PPS and so on, but how dies it know where the gun is, 50m, 200m, 600m???

If it sends only one pulse and it sends the pulse at random intervals before it receives the next pulse, what sort of timing does one look at? As I indicated above that spread is quite big, or does one just concentrate on the shorter distances eg transmit the pulse at (PPS - 30ns)??? But at the longer distances the TOF is say 3000ns so the the effect will be negligible.

If you want to vary the transmission of the pulse between say (PPS-30ns) to (PPS-300ns) it means that you will miss the window with some pulses if you are between 10m - 300m from the gun.

Now, how many pulses can you miss before they get a lock on you???

Or does the jammer estimate the distance by taking the doppler effect into consideration?


F@rk, this is getting serious now....... :(

jimbonzzz
02-12-2006, 04:51 PM
I don't know for sure how much timing variation is necessary, and I don't know how "tight" the algorithms in the guns are for computing speed. But of course you would want the gun to get different distance measurements that are inconsistent with a certain speed.

For example in the worst case scenario at 200 MPH (the max speed for the LTI Ultralyte), the vehicle is travelling at 293 feet per second. So for the Ultralyte LR operating @ 100 PPS it would expect the distance to decrease by about three feet for every pulse. Most guns will need 50+ consistent pulses for a speed reading.

About 1ns ~ 1 foot. So, I would expect that if one were to vary the timing by say 10ns for each jamming pulse, that it might look like a very large distance variation to the gun, since in the worst case @ 200 MPH it would only expect the distance to be different by 3 feet between each pulse. 10ns should also not cause a problem with getting outside of the window as you get close to the gun, because the Ultralyte specifications list the minimum range in speed mode at 50 feet. So you would actually have about 50ns or so to play with.

But then, another question comes up: do the jammers have this kind of timing resolution? As someone pointed out in another post before, a 10 MHz processor would only have 300ns resolution! :shock: But I think they are able to overcome this using hardware (slow discharge of a capacitor?) because I would think that 300ns would leave too much margin of error in the first place.

I don't think the jammers determine the distance to the gun...

Jim

Suf Daddy
02-13-2006, 07:09 PM
LTI Marksman 33 feet
Ultra Lyte (as Jim says above 50 feet)
Pro Laser III 10 feet by setting on the unit
Stalker Spec sheet says < 5 feet.BUT (if in weather mode) will ignore anything closer than 250 feet.

-Suf Daddy



<<<< SNIP >>>>>

What is the closest distance a lidar gun can measure at??