PDA

View Full Version : Veil applied to headlights' plexi (with pics). Comments?



Clandestine
07-18-2005, 02:10 AM
Hi, Veil Guy.
I have a few questions and I'd like others to share some opinions. I have applied veil, it's nicely applied, a smooth film - only one cover, not two, over my headlights' plexi, but in my opinion it's too dark. It also somewhat distorses the light beam. I was thinking if the good resulst could be achieved if I applied it actually onto the light bulbs/lens under the plexi front-glass. I have also noticed that during the night, when applied this way, the Veil film causes light glow like there was moist inside it - I'm pretty sure that anybody can see it, especially the police. What do you think, did I put too much (although I don't know how to put it less) of it on and should I try and dismantle the headlights and apply veil onto the glass (lens) of the headlights? Will the efficiency of Veil be reduced if I put in on the lights lens or is it meant to be applied like I applied it on the pics? Thanks for sharing your thoughts and opinions with me.

http://www.slovenj-gradec.si/Datoteke/pr/DSC00251_SM.jpg
Note the non-reflective headlight surface... Also note the Veil applied on chrome parts and Seat mark on the center mask.

http://www.slovenj-gradec.si/Datoteke/pr/DSC00252_SM.jpg
A little closer...

http://www.slovenj-gradec.si/Datoteke/pr/DSC00253_SM.jpg
Now that's how blurry it gets. Does it have to be this way?

http://www.slovenj-gradec.si/Datoteke/pr/DSC00254_SM.jpg
Another perspective. Btw. it's relatively invisible during the day. A little darker but to live with.

http://www.slovenj-gradec.si/Datoteke/pr/DSC00255_SM.jpg
Another close-up...

http://www.slovenj-gradec.si/Datoteke/pr/DSC00257_SM.jpg
Now, this is a night shot. Note the "moist" or smoke effect on the plexi...

http://www.slovenj-gradec.si/Datoteke/pr/DSC00259_SM.jpg
An upside-down shot.

http://www.slovenj-gradec.si/Datoteke/pr/DSC00262_SM.jpg
Front view, note how darker the headlights became...

http://www.slovenj-gradec.si/Datoteke/pr/7425_zm.jpg
...compared to this photo with original shiny headlights.

http://www.slovenj-gradec.si/Datoteke/pr/DSC00262_MOD_SM.jpg
And just for those V1 sceptics - upper mount is almost invisible and yet laser perception is fantastic.

TheGame
07-18-2005, 02:29 AM
I also applied a single smooth coat to my headlight covers and have gotten the same effect. I can tell when I pull into the garage that the light output is noticeably diminished compared to before. I'm not quite sure what to do other than possibly burn hi-beams at night to make up for it.

Clandestine
07-18-2005, 04:59 AM
Do you think it would be better if we applied Veil directly to inside lenses - lights instead onto front plexi shield? Do you think this would reduce the effect of Veil?

stalker
07-18-2005, 07:03 AM
man thats horrible....it doesnt do that to normal headlights without covers does it....

Clandestine
07-18-2005, 07:30 AM
Probably not. But I don't know. But this is somewhat annoying...

Crash
07-18-2005, 09:12 AM
Whoa... Probably just beginners´ "luck".

Veil Guy
07-18-2005, 10:15 AM
Clandestine,

From what I see in your PICs, you did all right.

Without getting into the details of how and why VEIL works, some of the effects you observed are the function of VEIL.

Light output, however shouldn't be dramatically reduced. If it is, you may want to consider using a light bulb like Silverstar or some other higher/whiter bulbs.

We do not recommend coating the inside of headlight housings alone. The lower gloss is one aspect of the VEIL function. You would likely reduce the efficiency somewhat if you forewent this aspect of VEIL.

BTW, in what country do you drive and what is a SERT?

Veil Guy 8)

SmaartAasSaabr
07-18-2005, 11:34 AM
SEAT is a Spanish car maker, they got bought out by Volkswagen AG around 1990, now their cars are basically reskinned VW's. Like Skoda actually, but Skoda is supposed to cover the bottom end, SEAT covers the "sporty" end...

Clandestine
07-18-2005, 12:14 PM
Veil Guy,
I was thinking of applying veil to the inner lights, onto the glass lens of the headlights, behind the plexi covers but thenm you think (I have to agree, you're probably right) than this would reduce the effectiveness of veil.
You probably meant Seat, a spanish car manufaturer? I drive in Slovenia, EU. Same regulations as elsewhere in Europe.

Clandestine
07-18-2005, 12:18 PM
Whoa... Probably just beginners´ "luck".

Hmm, not really, this is my second application of veil and the first one, with the brush, was far worse. This one was with the new 2'' foam and it spreads well over the surface. But man, it's dark and it actually diminishes the luminosity of the headlights.

stalker
07-18-2005, 04:55 PM
take the covers off, they are prob plastic PVC lenses anyway and it will take a good pounding to smash one of them, not like the old days when they wer glass.

I used to work for a major car manufacturer and tests proved that headlight covers are not needed with todays cars, they are built pretty tough.