PDA

View Full Version : LI arrived today, couple questions...



DougiesGoinDeep
07-23-2008, 04:06 PM
So it seems like double sided tape is the preferred installation method? What is the exact brand/name I should look for, and where can it be found? Any other tools or materials I should get while I'm out?

Just for the hell of it, here is a pic of the front of the car where I plan to put the 2 LI heads...
http://img237.imageshack.us/img237/833/e39lh4.th.jpg (http://img237.imageshack.us/my.php?image=e39lh4.jpg)
What is your pick? I want it there since Dorsce had good results in that area, and there is some controversy about mounting in the grill, vertical or horizontal (either way, if the lower position works, its much easier for wiring purposes).

noTe
07-23-2008, 04:27 PM
3M Double sided tape

erickonphoenix
07-23-2008, 04:42 PM
I apologize in advance for stating the obvious but be sure to clean the contact areas with rubbing alcohol and let it dry thoroughly.

the stuff will last a loooong time.

FoolishOne
07-23-2008, 04:48 PM
Yup, anything 3M VHB. You would break the product before the tape released.

DougiesGoinDeep
07-23-2008, 04:54 PM
great, can I get it at the local hardware store, home depot, or autozone, or radio shack?

Blinder Dude
07-23-2008, 05:39 PM
Auto parts store they will have the body mold tape by 3M.
If you are going to use tape instead of the brackets make sure before sticking the heads, they will be close to level, every little bit helps!
Level and straight to the road makes for a good install every time.
Blinder Dude

ahmadr
07-23-2008, 06:02 PM
Auto parts store they will have the body mold tape by 3M.
If you are going to use tape instead of the brackets make sure before sticking the heads, they will be close to level, every little bit helps!
Level and straight to the road makes for a good install every time.
Blinder Dude

It's so nice to see more reps participating in the forum in a positive fashion :)
Way to go Don, Mike, Cliff, and Leon :thumb2:

BTW we are missing Belscort and Valentine. Hear that guys?!
BTW2 I wonder if we could get go.mouse back...?

focalcivic
07-23-2008, 07:43 PM
As leon said 3m body molding tape in the auto paint section it is in a roll with a red backing.

By the way on your BMW's front plate there seems to be the "unmentionable" K jammer? Unless I am wrong?

DougiesGoinDeep
07-23-2008, 08:01 PM
As leon said 3m body molding tape in the auto paint section it is in a roll with a red backing.

By the way on your BMW's front plate there seems to be the "unmentionable" K jammer? Unless I am wrong?


Not my car, got the pic on google images. But is that what that is? Is that what all those thick black blocks are on the license plates? I've noticed them in person, it never dawned on me that it might be a jammer (I always figured it was for some sort of automatic door/garage).

focalcivic
07-23-2008, 08:05 PM
Not my car, got the pic on google images. But is that what that is? Is that what all those thick black blocks are on the license plates? I've noticed them in person, it never dawned on me that it might be a jammer (I always figured it was for some sort of automatic door/garage).


I am pretty sure that is what it is. I can not say the name, but their standard jammer is frame mount, they also have a 2 head unit that is led based.

ELVATO
07-23-2008, 08:06 PM
It seems it has some sort of laser receiver since it looks like it has one of those bubbles that are on the the ZR3/4s.

Stealth Stalker
07-23-2008, 08:15 PM
By the way on your BMW's front plate there seems to be the "unmentionable" K jammer? Unless I am wrong?
LOL! pwn3d :lol:

FoolishOne
07-23-2008, 08:40 PM
By the way on your BMW's front plate there seems to be the "unmentionable" K jammer? Unless I am wrong?

Yeah, the R&R's put this huge elephant in the room that nobody can talk about. It really irks me sometimes.

TSi+WRX
07-24-2008, 09:59 AM
3M Automotive Trim/Mo(u)lding Tape.

I'm actually not sure that it's VHB-based, as it is designed to be releasable, without leaving residual, albeit with either *excessive* time/exposure (and I mean on the level of a decade or more years), or with application of heat and mechanical stress (i.e. hair-dryer and fishing-line/dental-floss).

This is the stuff that auto-manufacturers use as OEM trim/molding adhesive, as well as is used by the aftermarket. Used for everything from cosmetic add-ons, including badging and lettering, to secondary-seal for even aerodynamic aids, such as spoilers/deflectors.

It's strong stuff, but like I said, still removable, without leaving any (or much, in the case of time/exposure induced, long-term stresses) trace.

---

Good prep is an absolute NEED - here's my post about using the 3M Automotive Trim/Mo(u)lding tape, from the LI Forums:



Try to take out as much strain/tension on the cable as possible, to allow the adhesive not have to work against this factor, especially during initial bonding. If you still feel unsure about this wonderful tape (which the OEM vehicle manufacturers use to achieve not only "permanent" bonding of just about all body badges, tags, and molding, but also even achieve "flush" bonding of a vehicle's aesthetic and even functional aero elements), you can (and I actually recommend this) "safety tether" the wiring, somewhere close to the head so as to prevent it from "swing damage," to the vehicle's trim or hardpoints via a Zip-Tie.

Remember these very simple rules for using the 3M Automotive Trim/Molding Tape:

(1) Pre-clean all surfaces. Remove dirt/grime via soapy water, and then dry thoroughly with lint-free towel.

- Optional - apply bond/adhesive promotor (on the vast majority of automotive bodywork finishes, this is NOT necessary.

(2) Pay attention to ambient conditions. Not only will a rainy day not be the best to do this (obviously, if your car's outside, and you don't have access to a garage!), but also if the surface to be adhered to is either too hot or too cold, it could cause worse-than-expected bonding and thus a degradation in long-term adhesive power. The former can be remedied by rubbing ice or pouring ice-water on the bonding surface immediately prior to final prep, and the latter via using (carefully!) a hair-dryer (NOT HEAT GUN!) to raise surface temperature to acceptable.

(3) Final-prep either with isopropyl ("rubbing") alcohol or high-grade ethanol, and allow to either air-dry or dry with true lint-free towel.

(4) Initial placement can be "*VERY* light contact," which will allow you to visualize what the final placement will look like, without truly committing. Once you've made sure that you've got it just right, PRESS HARD to lock in the placement.

(5) Check alignment. Sometimes, after initial installation, there's a bit of "settle" effect. You'll want to be sure that you've got things the way you want it. It is possible to "double-up" on the tape to effect a makeshift shim, but keep in mind that this tape is compressible and deformable, and again, check alignment after such an effort.


Best place to look for this stuff would be your local automotive parts retail chain.

Packaged in a blister pack for hanging displays, black backing with white/yellow lettering. The tape body is grey, and will have a dark-red backing (grey-and-red spiral, slightly smaller than the size of a CD, for the large roll). There's usually a half-inch and a quarter-inch width sizes available for selection. Use the half-inch width version, which also makes it easy to "double-up" along its width to serve as shims.

Check where the paints or, more usually, where the adhesives/tapes are located. Both, in-turn, may be located in the "body work" section of the store.

You should easily be able to ask for this item by-name.

Also, pick up some black duct-tape or electrical tape, of muted/matte color, to serve as cosmetic camouflage for the exposed "height" of the tape, after you've affixed it on-vehicle (i.e. the exposed part between the upper surface of the jammer head, and the surface to which it is in-turn adhering to).

Note that the tape is highly pliable/deformable. This can make it rather difficult to work with, but you'll get the hang of it in no-time. :)

-----

BTW, I've heard from a fellow automotive hobbyist that this tape is now available in BLACK. I've yet to see it, though...... :confused:

DougiesGoinDeep
07-24-2008, 05:06 PM
As usual Allen, extremely helpful. I'll try to head over to auto zone tonight or tomorrow. If the monsoon here in Boston ever stops I might even get a chance to install the thing.

tosi
07-24-2008, 06:23 PM
.....

TSi+WRX
07-25-2008, 07:45 AM
Hope y'all's weather gets better! :eek:

---

DGD, never a need to thank me - just glad to help fellow hobbyists. :)

BTW, even in very high humidity (heck, even if the surface has some water on it), that tape *will* stick. So if you need protection "right away," go ahead, and do a quick-and-dirty for the time being, you'll be just fine.

Just be sure to revisit the install when the weather clears, and to "safety tie" the heads, too!

Tambourine-Man
07-25-2008, 08:17 AM
Matt,

I no longer think tape will work for mounting vertically in the grill slots, but previously I wrote to 3M about their Dual Lock tapes:

Here is the reply:

Thank you for your inquiry.

I would suggest you try our Dual Lock SJ-3550 (black) or SJ-3560 (clear).
These have our high performance VHB adhesive that should bond to the
exterior and have good temperature and outdoor elements resistance. They
should hold up to wind, but with any application we do suggest you test it
first.

If you need further/additional assistance or prefer to speak directly with
a specialist please call 1-800-362-3550 for the first available
representative.

Regards,

Lisa
3M
Industrial & Transportation Business
Customer Response Center
1-800-362-3550

################################################## ###

Message = Can (any of) your Dual-Lock products with adhesive backing be
used in an exterior automotive application where they are subject to wind driven moisture and high temperatures (but well under 220 degrees F)?

DougiesGoinDeep
07-25-2008, 12:24 PM
I'm going with the horizontal mount in the lower grill. It's nice out now, I'm going to give it a shot. I'll post some pics when I'm done.


Matt,

I no longer think tape will work for mounting vertically in the grill slots, but previously I wrote to 3M about their Dual Lock tapes:

Here is the reply:

Thank you for your inquiry.

I would suggest you try our Dual Lock SJ-3550 (black) or SJ-3560 (clear).
These have our high performance VHB adhesive that should bond to the
exterior and have good temperature and outdoor elements resistance. They
should hold up to wind, but with any application we do suggest you test it
first.

If you need further/additional assistance or prefer to speak directly with
a specialist please call 1-800-362-3550 for the first available
representative.

Regards,

Lisa
3M
Industrial & Transportation Business
Customer Response Center
1-800-362-3550

################################################## ###

Message = Can (any of) your Dual-Lock products with adhesive backing be
used in an exterior automotive application where they are subject to wind driven moisture and high temperatures (but well under 220 degrees F)?