PDA

View Full Version : New ZR4: Install Pictures, Highway Tales, and Questions



John From Cincinnati
07-27-2008, 07:04 PM
Greetings. About a month ago I began researching radar detectors in preparation for a road trip. I stumbled upon this site and have been reading through the wealth of information present here ever since. Great information and great community of folks; well done.

I am unable to find the referenced Introductions forum to properly introduce myself. In any case, I thought the ZR4 section to be the most pertinent place to present the slew of stuff I've got. Please excuse local details and the length of this post.

I initially purchased a Beltronics V940, and was quite pleased with its performance. Used it on two road trips, to D.C. and NYC, and it performed quite satisfactorily, especially considering the price. Further research and real-world usage of the detector revealed that it was a fine choice, but given where I do the majority of my driving (Ohio highways), sooner or later I was going to get popped by Lidar. I had quite a close call on westbound I-70 a couple hours out of Columbus, anyone familiar with the area would recognize the spot, coming out of a forest, so to speak, around a blind curve to be hit at probably 600-800 feet by a State Trooper. Hearing the detector yell "Laser Alert" was disconcerting, as I knew he had me clocked by then. Luckily, my 78 in a 65 wasn't enticing enough for him to give chase.

I decided to further research active countermeasures. After much internal debate, I settled on a ZR4, based on several factors. 1. It "synced up" with my V940, which in hindsight really isn't that big of a factor. 2. Bel/Escort (incidentally V1 as well) is located roughly a 5 minute drive from where I work; I purchased the ZR4 from them directly as I wanted to test it out first with the option of returning it if I was dissatisfied with the performance. And finally, 3. I liked the price, and the fact that it offered (arguably minimal, but nonetheless existent) rear protection as part of the package. I have spotted State Poopers shooting lidar from the on-ramp (71 North, Dana Ave. on-ramp if you're familiar with the area) into passing traffic, and wanted to at least be notified when they were doing such things.

I very nearly went ahead and ordered a dual LI with an extra head. I still may do a dual head for the front, in fact, at some point down the road. However, I couldn't justify the extra expense over the ZR4. I tend to be a fairly alert driver, and I felt the ZR4, though it probably won't provide consistent JTG performance, would be sufficient to at a minimum afford that additional couple of seconds needed to slow into the safe zone.

I've had the ZR4 installed for roughly 2 weeks, and to this point have been quite satisfied, to the extent that I went ahead and epoxyed the brackets on for more permanent mounting. Please find a picture of both the front and rear shifter heads below. Vehicle is a 2003 Chevy Impala.

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr42.jpg

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr41.jpg

The front heads don't look level left to right do they? I know they are front to back, but looking at this picture I realized I only eyeballed the left to right. I think it's just the way the air dam or whatever is cut. The next pic below makes it look a bit better, I'll go check it after I post this, If I have to rip up that epoxy I'm not going to be pleased:D.

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr45.jpg


A couple points of discussion: I am a little concerned about the front heads' distance from the headlights. I think I've got the front plate covered, as well as a leg up as far as the vehicle color and the fairly small reflective surface area overall, but I may consider hacking up the grill at some point to accommodate the heads. I also may hack up the grill to accommodate two LI heads, but that is more long-term. I think some Veil may be in order, especially given the ZR4's weakness with the Stalker and the Veil's apparent good results against that particular unit. I've seen the Stalker listed in the state specific section for Ohio, but I am not to the point where I can i.d. these as I am driving by. Anyone more familiar with what the local yokels are using, or can anyone point me in the direction of a resource I might use to try to become more familiar with the different units and be able to i.d. them?

The rear head is mounted at the bottom of the plate due to it partially obstructing the license plate light when mounted at the top. I think it probably would marginally better protect the rear if mounted at the top, but I'd like to avoid any tickets for not having the plate properly illuminated, as well as not draw attention to the odd apparatus that is blocking the light:).

Any thoughts on any of these issues?

Below is a pic of the ZR4 display, mounted in front of the instrument panel. I may move it, as all warnings are delivered through the detector, so it doesn't really do me any good to have it in my field of view. Also note the remote mute button I've mounted in an empty switch spot. This is greatly helpful as I no longer have to either stick my arm through the steering wheel to mute the ZR4 or mute from my now high-mounted, hard-wired detector.

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr43.jpg

In the roughly two weeks I've had the ZR4 installed, I'd give it two definitive "saves". Southbound 71 immediately after the Pfieffer Rd. exit (again, just for those familiar), I was hit at approximately 1000 ft. doing 84 in a 65 in relatively light traffic. This is an atypical location for them to be shooting; I'm usually able to spot them before the ZR4 alerts, but not this time. I slowed to the posted limit as quickly and discretely as possible, and killed the shifters. The detector was alerting the entire time, until just after I killed the shifters. This, and the fact that I was not ticketed for 19 over, serves to make me feel as though the ZR4 was doing its job. The officer didn't give me a second glance as I drove by, just continued targeting the next potential victim. I suppose this is a good thing, but I would have preferred a confused look so that I could be sure. 2nd save occurred in a 55mph zone, I was doing 72 when I was initially hit. I was worried about this one, as it was a Trooper on a motorcycle leaning against the concrete barrier in the median. I think he was probably shooting at the driver's side headlight. In any case, the ZR4 alerted only briefly (2 seconds perhaps) while I slowed. I wasn't even able to kill the shifters as he had moved on to the next vehicle. Again, nothing out of the ordinary as I passed. Traffic was a bit heavier this time; I think he probably gave up and moved on. In both these situations I feel had I been clocked at the speed I was traveling, or even shortly after I was alerted, I would have been ticketed.

There have been several incidences of being hit with Lidar while traveling at speeds less than 15mph over. I made an intentional loop through the feeding frenzy just north of downtown Cincy the other day after seeing multiple traps, got hit 6 times in the 15 mile loop I traveled. While it was fun, I don't know that the information I gained was that useful, as I wasn't going much over the PSL at all.

I have had what I feel are some false alerts, 4 now to be exact. Two I attribute to Infiniti vehicles behind me. Both were continuous rear alerts after another vehicle moved out of the way and an Infiniti was then directly behind me. A third I am more unsure about, I got a front alert after moving in directly behind a fairly new Escalade. I don't know if some sort of adaptive cruise control system on a Caddy would have any need for a rear facing laser, or if it was perhaps some sort of parking sensor or something, but I feel strongly the Cadillac was the source. It certainly wasn't any police Lidar, as I'm quite familiar with the area and there were no units present. My best guess on the last false is the sun, I was going directly into it and it was fairly intense, I couldn't discern any other reason for the alert.

Last picture, I picked up just yesterday a Passport 9500i. A buddy was going to buy a Bel V940 anyway, so I made him a good deal and helped myself out in the process.

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr44.jpg

Very pleased with it so far, I have a couple very annoying radar falses on my daily commute (stupid BMW Store), and the silence has been golden thus far. I may kick myself for not waiting until tomorrow and spending the extra $50 for the 9500ix from Escort directly, but we shall see.

And that's all I've got. So far, I'm very pleased with everything I've used. I'd definitely recommend the V940 to someone on a budget; there is a slight but discernible difference in detection range between it and the 9500i, but it was very good itself. 9500i has been great so far, as has the ZR4. Sorry for the long post if that bothers anyone; I always enjoyed reading similar posts so I figured I'd give back in the hopes that this will help someone as others helped me.

Anyone from the Cincinnati area? I saw a (I assume) gentleman named Bearcat who is around these parts. I'd love to get a similar group together as have other areas for some testing. I don't have any Lidar guns but would be happy to chip in to rent some if that is a possibility. I imagine there are folks from Kentucky and Columbus around as well who might be interested. Any takers?

Thanks for reading, hopefully helpful to someone who was in my shoes a few weeks ago, and thanks in advance for any thoughts or comments.

John (from Cincinnati)

PMoth
07-27-2008, 07:31 PM
Welcome to the forum. Holy long read Batman!!! I have to digest all of this before I make any comments or recommendations. I will start off with your heads are too low. More to follow.

AirMoore
07-27-2008, 07:52 PM
Welcome to the forum... and very nice set-up you have there (between the RD and the ZR4).


Also nice install (inside) on the ZR4... but I agree that the heads are a bit too low for headlight coverage. (Measuring them and see how far they are from given areas on the headlight and report back).


As far as the saves, its most likely that you were saved both time:

To be honest it seems as if in most real world encounters the LEO's are not as shall we say 'versed' in how *more specifically*: where/what to target to obtain the best/fastest readings. They are so used to haphazardly aiming at a car... anywhere and getting near instant locks, that they mostly just go for center mass. Often times in jammer test the 'worst case scenario' for a jammer is worked upon, and also the people shooting the gun start finding the 'weak spots' type deal.


Overall good set-up. Always nice seeing a good jammer install, how long did it take? Also the more pics the better! Keep it coming, and again welcome to the forum and enjoy your stay.


PS: Look into veil G4 for the headlights. ;)

Lucky225
07-27-2008, 07:58 PM
yea, like you said, would be better mounted at the top, esp since the rear jammer gives you only marginal protection to begin with. I would suggest looking into a personalized plate design where the word 'OHIO' is displayed lower on the plate if your state offers such a design it would be a good grab.

focalcivic
07-27-2008, 09:04 PM
I really wish you did not use epoxy for the fronts. Even if you used screws you would of be fine plus much easier to remove.

Another suggestion the Zr4 display does not have to be inline of sight esp in the dash cluster I would move it to a center console area.

06blackgto
07-27-2008, 09:16 PM
I agree your heads are too low... here is where I mounted my zr4 heads, even then I wish I could go alittle higher.....
don't mind the bugs, I drive 100mi. roundtrip to work at night... but I do clean them off everyday....lol
http://i79.photobucket.com/albums/j159/importkiller_2006/DSC04720-1.jpg

http://i79.photobucket.com/albums/j159/importkiller_2006/DSC04721-1.jpg

crazyVOLVOrob
07-27-2008, 10:21 PM
I would suggest you use some VEIL and put a laser shield on front plate

John From Cincinnati
07-27-2008, 10:22 PM
Thanks for all the replies and input! The people have spoken, and the heads must be moved. As evidenced by the long post and hasty epoxying, I tend to overdo it a bit sometimes :o. As requested, some measurements to ponder.

http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr46-1.jpg

I went at it initially trying for the cleanest, most concealed install. The yellow bars location shouldn't be too much trouble as far as mounting, that piece is still plastic. Pink bars location would require some creative dremeling (I don't want to use those grille clamp mounts), and doesn't (to me) seem to gain me much, if anything. Thoughts on yellow bar spots?

Thanks for the rear plate suggestion, Lucky. Ohio unfortunately doesn't offer a plate like that. Also, the rear head casts an upside down V-shaped shadow right down the center of the plate when it's at the top, such that there's a good 6" of plate at the bottom that isn't illuminated. The only solution I can think of is to get some maybe 1/2" or 3/4" nylon spacers between the plate and the rear head bracket holes to raise the head up off the plate a bit and allow the light to pass behind it. I actually think I'll give that a shot and see how it works.

I will be slathering on some Veil when it becomes available.

Thanks again for the kind words and input.

Lucky225
07-27-2008, 10:31 PM
Wow, all Ohio plates have the same banner at the top, that's crazy. Any event, regarding the 'shadow' effect. You can buy these things called 'light'n'boltz' where instead of screwing in regular screws through the laser jammer and plate you screw through these bolts that have LED lights in them and shine down on the plate, I bought some after getting pulled over for my LP light being 'blocked' and haven't been pulled over since.

MEM-TEK
07-27-2008, 10:48 PM
Hi John,

Welcome aboard! I thoroughly enjoyed reading your post. I've got the same problem with rear license plate illumination. I went to the local hardware store the other day, but they didn't have any Nylon spacers. I guess I will have to make a longer trip to Lowes on the far side of town.

I love where you mounted the mute button. That is really discreet and convenient. Also, I kind of like the yellow mounting positions for the front heads. You might want to shoot a nighttime flash photo of the front of your car from a distance of at least 20 feet away so that you can then see where all of the highly reflective front areas are located. That might help you decide between the yellow or magenta positions, or even possibly to leave the heads where they are.

Lucky225
07-27-2008, 11:16 PM
yea I just looked at the mute button pic when you mentioned that, hah that is slick, memtek, like I said look into Light'N'Boltz, they're a little pricey (like $30 for 2), but well worth it

focalcivic
07-28-2008, 08:29 AM
There is no issue leaving the rear head attached to the lower bolts, since the rear head is minor protection if none, but more of a receiver, and with the rear you will not block illumination.

TSi+WRX
07-28-2008, 10:49 AM
Good stuff, John, and a big welcome to a fellow Buckeye! :)

Like the others here have said, I'd also say to move the heads further up - without conclusive testing data, it's hard to say, one way or the other, but looking at your diagram above, it does seem a bit far of a reach to cover the entire headlamp units....and I would imagine that your centerline, as you move further "up" the vertical axis, would also show weaknesses.

I'd say that yellow would be ideal, particularly as you should also pay good attention to the front plate - but without some measurements as you've done, and without true testing, it's hard to tell whether or not the pink setup might actually be better.

In terms of the rear, I feel your pain - indeed, my vehicle is configured similarly, in terms of the rear plate illumination, and I also could not put the rear head (my ZR3) above the plate.

In residing "under" the plate, you now have two considerations:

(1) The jammer head is less effective - they're now so low that they're effectively only, well, effective :o for direct-plate shots, in terms of protection. Don't carry any illusions in this respect, my fellow Escort user and Buckeye - particularly for vehicles of your size, and with such a rear hardpoint profile, rear jamming is *not* something to be optimistic about. I see my rear ZR3 head as a receiver only - with the primary benefit being that it will alert me to the direction of the incoming LIDAR threat.

(2) Regardless of performance concerns, make sure that the head is properly leveled - it looks from your picture that there's a bit of incline to the plate-mount plane (this is true on my car), so you may need to bend the bracket a bit (or shim), to achieve good placement/aim.

If you do bring the head up and over the plate, aftermarket lighting solutions (LED strips, LED-impregnated bolts, etc.) can allow you to work around the illumination issue (be sure to double-check that the aftermarket solutions do offer enough light, of the correct "color," to the plate, too), and if you get creative with some pieces of plastic or metal, you can also effect - if there's sufficient space - an "above the plate" mounting by "extending" the factory rear jammer head's bracket, and fitting the bracket *behind* the plate, allowing only the jammer head to drape over the rear plate.

John From Cincinnati
07-29-2008, 10:37 PM
Thanks everyone for chiming in. Few things to update. I messed around with relocating the front heads. I actually bent one of the supplied brackets to the point that I stressed it too much and it broke. Luckily Bel/Escort, being right up the road, was kind enough to offer 2 replacements for free (shout out to David, good guy up there). I bent some temporary brackets out of light gauge aluminum and mounted the heads roughly in the spots indicated by the yellow bars. Mounting with the replacement brackets is going to be difficult. The plastic portion of the top part of the bumper is nowhere near level, requiring a pretty extreme bend in the bracket, which the bracket doesn't like one bit. We'll see how it goes. I am going to go with the yellow bar spots unless someone makes a strong case in favor of the pink. I feel that the yellow more adequately centers me between the headlights and license plate both vertically and horizontally. With the pink spots, the edge of the shifter head is roughly 24" from the edge of the head light, which I'm not entirely comfortable with. In the yellow spots, I should have no more than 18-20" out to the very edge of the headlights, and a couple inches less from each head to the headlight. I will go with Veil on the headlights as well.

As for the rear, I'm probably going to go with mounting the head on the lip on the back bumper directly above the license plate. This picture Ironic Police Car Picture (http://images14.fotki.com/v255/photos/4/49373/2960805/cnpca4239a-vi.jpg) shows the lip I'm referring to better than my crappy picture. I think it will be much more level, and will alleviate any light blocking issues. I plan to Veil the crap out of the actual tail light sections of the rear, but it would take an awful lot to cover that entire rear area. Hopefully the rest of that area with the exception of the tail lights isn't too reflective. With the addition of Veil and the fact that the vehicle is black, it's probably as good as I'm going to get with the ZR4 rear, and I'm just going to treat it as a receiver from here on out.

MEM-TEK
07-30-2008, 04:14 AM
Either the yellow or pink locations -- not too much difference there. Notably, for the rear, definitely shoot a night flash shot of the rear of your car. You need to find out where the rear corner-cube reflectors are installed on your rear tail lights. The flash camera shot will show where they are since they will stand out in the photo plain as day. Those things are critical to cover with Veil.

los scion xa
07-31-2008, 09:30 AM
http://i272.photobucket.com/albums/jj193/draza11232/IMG_0472.jpghttp://i272.photobucket.com/albums/jj193/draza11232/DSC02724.jpg http://i272.photobucket.com/albums/jj193/draza11232/DSC02725.jpg http://i272.photobucket.com/albums/jj193/draza11232/DSC02726.jpg http://i272.photobucket.com/albums/jj193/draza11232/DSC02727.jpg http://i272.photobucket.com/albums/jj193/draza11232/DSC02729.jpg

I did install my self I didn't think it wood work till I was doing 58 in a 30 the Escort 9500i when't off lasr shifter on the Escort ZR4 Jammer stated jamming the cop looked at his gunn and I keeped on going. NICE

AirMoore
07-31-2008, 11:40 AM
Los Scion Xa: Welcome to the board... its great to see more female members on here! (Especially ones whom do the install on their own). It looks nice. Personally I would be a bit worried about PT at closer distances, though your set-up seems to be at an optimal placement. I would look into lasershield for that front plate.


That is a hard car/automobile to cover, especially with the front plate from NY. (I live there also... in Central NY), and the troopers on the thruway, are just amazing with lidar.

In anycase nice set-up and its great to hear you had a save already! (Though thats a bit quick to be going in a 30 and hoping a jammer is going to save you... had he been using instant-on: You would be toast.)

---------------------------------------------------------------------------------



To the original posters, I think the moving of the head placement is a good idea. I cant wait to see some more pictures of the set-up.

BossMan4Life
08-10-2008, 02:39 AM
I bet you no woman alive installed jammers on her own car.

PMoth
08-10-2008, 02:02 PM
I bet you no woman alive installed jammers on her own car.

Unfortunately, I think you're 100% correct on this one.

TSi+WRX
08-10-2008, 02:38 PM
^ Hopefully, my baba-Anna will change this, in the years to come. :p

--------

But actually, there's always been a subset of auto-enthusiasts who are women, and many of these are, actually, DIYers.

Only more recently have I met "tuners" who fit this bill - in the past, it's always been hot-rodders of the classic Detroit genre.

Things are changing. :)

John From Cincinnati
08-16-2008, 07:12 PM
Finally, an update.

I considered returning the ZR4 after the GOL results were released, but have decided to keep it. I don't know that the 30-day money back thing applies to the ZR4, so I may not have been able to anyway, but I continue to have acceptable results with it in the real world. I am looking into renting a lidar gun from a member here, so I can do a little testing myself for peace of mind. Any suggestions on which gun to get? I'm thinking Stalker but I don't know if its reputation as most difficult to jam translates to the best choice for what I'm looking to do.


http://img.photobucket.com/albums/v192/bigjohnwhodatis/ZR4.jpg

The bumper was too slanted to use the provided brackets to mount, so I ended up cutting out a section of the grill and installing the heads there. I painted the chrome portion with a flat black Krylon, which I think looks better than it did before. I'm ordering a can of Veil tonight, and Mem-tek I promise to take night shots soon.

I think I saw a TruSpeed near downtown Cincy on 71, cop (State Trooper) was shooting on the right hand side and I was in the far left lane, all I saw was a blue case. Any other gun out there that has an all blue case? It looked to be a shade darker than the blue I've seen in pictures, but I haven't seen pictures of anything else with an all blue case like that. He unfortunately didn't target me, so I can't speak to the ZR4s performance. I will admit to circling back around and coming through the area again at about 25 over PSL, attempting to potentially sacrifice myself for the betterment of the community, but he had a customer by then.

John From Cincinnati
08-16-2008, 08:16 PM
As promised, a rear night shot.


http://img.photobucket.com/albums/v192/bigjohnwhodatis/zr42-1.jpg

Better than I expected. I'll obviously cover the reflecting areas well, and will probably put some on the other taillight area even though it's not reflecting much in the picture. The blue on the bottom of the plate (haven't moved it yet) is the rear ZR4 head reflecting. Kinda neat.

focalcivic
08-16-2008, 08:20 PM
Finally, an update.

I considered returning the ZR4 after the GOL results were released, but have decided to keep it. I don't know that the 30-day money back thing applies to the ZR4, so I may not have been able to anyway, but I continue to have acceptable results with it in the real world. I am looking into renting a lidar gun from a member here, so I can do a little testing myself for peace of mind. Any suggestions on which gun to get? I'm thinking Stalker but I don't know if its reputation as most difficult to jam translates to the best choice for what I'm looking to do.


http://img.photobucket.com/albums/v192/bigjohnwhodatis/ZR4.jpg

The bumper was too slanted to use the provided brackets to mount, so I ended up cutting out a section of the grill and installing the heads there. I painted the chrome portion with a flat black Krylon, which I think looks better than it did before. I'm ordering a can of Veil tonight, and Mem-tek I promise to take night shots soon.

I think I saw a TruSpeed near downtown Cincy on 71, cop (State Trooper) was shooting on the right hand side and I was in the far left lane, all I saw was a blue case. Any other gun out there that has an all blue case? It looked to be a shade darker than the blue I've seen in pictures, but I haven't seen pictures of anything else with an all blue case like that. He unfortunately didn't target me, so I can't speak to the ZR4s performance. I will admit to circling back around and coming through the area again at about 25 over PSL, attempting to potentially sacrifice myself for the betterment of the community, but he had a customer by then.


Research what guns are used in your area then if you can rent that, I would, as for the Truspeed the CFL group is having a test soon and Cliff has the Truspeed coming.

MEM-TEK
08-16-2008, 09:53 PM
As promised, a rear night shot.

Better than I expected. I'll obviously cover the reflecting areas well, and will probably put some on the other taillight area even though it's not reflecting much in the picture. The blue on the bottom of the plate (haven't moved it yet) is the rear ZR4 head reflecting. Kinda neat.

Here is an enhanced version of your photo:

http://img80.imageshack.us/img80/6993/image1at1.th.jpg (http://img80.imageshack.us/my.php?image=image1at1.jpg)

Wow! Your car is pretty stealthy from the rear. Veil out those built-in corner-cube reflectors on the end taillights, the center tail light, and the vehicle logo, and you should be rather well protected! :D

John From Cincinnati
08-17-2008, 12:40 AM
[QUOTE=MEM-TEK;436937]Here is an enhanced version of your photo:

http://img80.imageshack.us/img80/6993/image1at1.th.jpg (http://img80.imageshack.us/my.php?image=image1at1.jpg)

Wow! Your car is pretty stealthy from the rear. Veil out those built-in corner-cube reflectors on the end taillights, the center tail light, and the vehicle logo, and you should be rather well protected! :D[/QUOTE

Thanks for the enhancement! Yeah the rear turned out to be alright. It'd be nice to actually be targeted from the rear by something other than Infiniti cruise control.

TSi+WRX
08-17-2008, 09:53 AM
:eek:

Yikes! Thanks for the TruSpeed sighting!!!! :eek:

---

I honestly think that your eyes were accurate - that you did spot a true TruSpeed.

Ohio was rumored to be among the states that put in for the first bids, and given our enforcers' love of LIDAR, it's not at all unlikely that any new piece of equipment would have been fast unboxed, and pressed into action.

Certainly, I think that the "black" of the other LTI guns, as well as even the Laser Atlanta "S," could pick up some surrounding/environmental hues and have, combined with lighting conditions, appeared more bluish (heck, I'm looking out of my house's back window, now, and my garage looks blue!), but I truly trust your sighting.

Yes, the Laser Atlanta "S" variant's physical shape is even - well, if you squinted really hard, with only one eye open, sideways - kinda like that of the TruSpeed's.

^ That's why I honestly think what you saw was real.

And thanks, fellow Buckeye, for the warning!

----

As to the rental.....

Well, the Stalker should be your "worst case" scenario, given the ZR4's observed performance via all the different independent hobbyist testing.

But what I worry about is whether if the ZR4's performance would be just so bad against the LZ-1 that you won't be able to "optimize."

I dunno...... :confused:

MEM-TEK
08-17-2008, 10:34 AM
...Well, the Stalker should be your "worst case" scenario, given the ZR4's observed performance via all the different independent hobbyist testing.

But what I worry about is whether if the ZR4's performance would be just so bad against the LZ-1 that you won't be able to "optimize."

I dunno...... :confused:

With the ZR4, head placement and head leveling is everything when dealing with the Stalker. Never let the front ZR4 heads tilt up. The front heads must be mounted within a range of tilted upward 1 degree to to tilted downward by up to 2 degrees. You can't let the front heads tilt up more than 1 degree since the LEDs, mounted further back atop the circuit board, will then be slightly shadowed by the circuit board. Mounting the heads dead level of course is ideal. :)

focalcivic
08-17-2008, 12:13 PM
:eek:

Yikes! Thanks for the TruSpeed sighting!!!! :eek:

---

I honestly think that your eyes were accurate - that you did spot a true TruSpeed.

Ohio was rumored to be among the states that put in for the first bids, and given our enforcers' love of LIDAR, it's not at all unlikely that any new piece of equipment would have been fast unboxed, and pressed into action.

Certainly, I think that the "black" of the other LTI guns, as well as even the Laser Atlanta "S," could pick up some surrounding/environmental hues and have, combined with lighting conditions, appeared more bluish (heck, I'm looking out of my house's back window, now, and my garage looks blue!), but I truly trust your sighting.

Yes, the Laser Atlanta "S" variant's physical shape is even - well, if you squinted really hard, with only one eye open, sideways - kinda like that of the TruSpeed's.

^ That's why I honestly think what you saw was real.

And thanks, fellow Buckeye, for the warning!

----

As to the rental.....

Well, the Stalker should be your "worst case" scenario, given the ZR4's observed performance via all the different independent hobbyist testing.

But what I worry about is whether if the ZR4's performance would be just so bad against the LZ-1 that you won't be able to "optimize."

I dunno...... :confused:


Sounds like you are in denial my friend, LOL. Truspeeds are in operation, CT is using them as we speak, I posted an article with a cop holding the Truspeed and that was a few weeks ago. To further this point Cliff is taking delivery in the next few days.

I was in CT the other day hunting down the Truspeed, not only did I not see one Truspeed, I didn't even see a cop, LOL.

TSi+WRX
08-17-2008, 01:23 PM
^ :lol: Yep, I keep hoping that Ohio won't see the TruSpeed just yet, but based on how fast the roll-out happened in CT, and this latest sighting from John, I think it's reasonable to say that I'm glad I don't do much highway travel, any more. :p

I knew from the beginning that Ohio was among the lead states, but I never dreamed that it would happen, so fast.

MEM-TEK
08-17-2008, 01:33 PM
^^ Happya$$ keeps telling me that Ohio is deadly with all of their laser guns. I guess Ohio tries every laser gun they can get their hands on, maybe trying to find what laser guns are the quickest and most reliable to use in order to rake in the most speeding fines per hour? Revenue, revenue, yum yum yum. :D

focalcivic
08-17-2008, 04:49 PM
^^ Happya$$ keeps telling me that Ohio is deadly with all of their laser guns. I guess Ohio tries every laser gun they can get their hands on, maybe trying to find what laser guns are the quickest and most reliable to use in order to rake in the most speeding fines per hour? Revenue, revenue, yum yum yum. :D


I wouldn't be surprised the Truspeed turns out to be junk LOL.

John From Cincinnati
08-20-2008, 09:15 PM
Thanks everyone for the input!

As for the gun rental, cross referencing GOLs results with the state specific laser gun list, I think the LTI Ultralyte (125pps rev) or the Marksman would be a good choice; I'll probably go with the Marksman. It did as poorly as the PLII, and is second on OH's list. Now that I think about it, with the exception of the LA, there isn't a gun that GOL tested that would be a poor choice... Seems to me however that my far-from-worst-case application is holding up, Veil arrives tomorrow so hopefully that firms things up even more.

Still keeping a look out for the potential Truspeed, haven't gotten any good laser shots recently to speak of, just a nighttime shot a couple days ago. Once I get the Veil on I'm going hunting.