View Full Version : I need your suggestions regarding my installation!
MEM-TEK
07-27-2008, 09:21 PM
Hi everyone,
I could really use your suggestions regarding my 9500ci's shifter installations.
-- The frame with the Hyundai logo (circled in yellow) is going to be replaced with a new frame which I ordered the other day. The new frame is painted with flat black primer paint. I also plan to paint the area behind the frame circled in yellow with flat black paint.
-- I plan to paint the areas (circled in orange) behind the bumper flat black.
-- I then plan to move the front ZR4 shifters to the locations shown in red or possibly to the locations shown in green. What do you guys recommend, taking into account the other modifications mentioned above which I plan to do?
-- Finally, I bought a black license plate frame with a clear plastic plate cover. I plan to paint these items flat black and install them on the front of my car.
http://www.mem-tek.com/radar/reviews/9500ci/installation/Hyundai_front_1000x740.jpg
The rear of the car is a lot simpler as seen in the photo below. It looks like all I have to do is to apply some Veil to the corner-cube reflectors built into my rear tail light assemblies. As you can see, these built-in corner-cube reflectors are quite efficient at returning light or laser IR back to the source! Obviously I can't just simply put some tape over these corner-cube reflectors since this would be a violation of state law. Do you guys think that Veil will kill the IR for these reflectors?
http://www.mem-tek.com/radar/reviews/9500ci/installation/Hyundai_rear_1000x740.jpg
Well, I look forward to your comments, suggestions, or any other ideas which you can think of! :)
rsatmans
07-27-2008, 09:42 PM
Mike,
I would simply move my front heads down to the red. I would not add any items like a black frame or plate to the front this will only add more vertical surface area for the laser to reflect back to the gun with. I think that by simply moving you heads down to the red you will greatly reduce your PT. On the rear Not much you can do. I would say veil g4 when it comes out maybe addition of laser plate cover. I plan to split some g4 veil with marty for the rear and we are going to apply to our rear taillights. This should give you great performance hopefully once g4 comes out we can do some more testing.
ahmadr
07-27-2008, 10:19 PM
red is good, green is bad
veil (or anything else) on the reflectors is a good idea. I'm amazed the bulb reflectors don't reflect much.
I wouldn't expect the black plate and grill to make a lot of difference. The headlights are a much bigger reflector. Check out this method to give you some ideas what should be your priorities:
http://www.radardetector.net/forums/veil/23317-sample-reflectivity-profile.html
Basically, use maximum zoom and fastest possible shutter speed, vs what you have done now :)
TSi+WRX
07-28-2008, 11:15 AM
I'd go for the "red" as well......
Although, as with other similar installs of that nature, I remain somewhat afraid at what an extreme-distance/angle "over the crest" shot might do, as it would stand to-reason that the bumper skin, protruding ahead of the jammer head, would cause line-of-sight interference under such conditions.
Still, this worry of mine remains an untested scenario, and as such, I don't even know if it is a real-world worry, based on the angles encountered. Nevertheless, I had to put this one out there.
Overall, I'd think that the "green" setup would place both your center-mass as well as the upper corners of your headlights farther out from the protective coverage of the ZR4 - however, given how amazing it seems to be in terms of a receiver (as seen from Cbr and ELVATO's IR-videos), I don't know that would matter at all. Instead, it may be that getting the heads closer to the potential points-of-aim may return for you better performance by such proximity.
Only one way to tell - mount, and re-test. :)
Since you have the both the technical capability to do so (to mount and re-mount), and you also have access - if only periodically - to testing gear, I think that if you're trying to optimize your setup, you should pursue, at least temporarily, only "temporary" mounting - and only finalize when you've reached what you've determined to be the technical extent of the jammer's capabilities.
---
REAR:
I'd say to VEIL the sucker. :)
It worked for LittleOverPSL - at least with audible return, the tones were noticably different. To the best of my knowledge, he'd never tested tail-lamp VEIL'ing (G2) on a quantitative basis, in terms of actual runs versus his LIDAR equipment, but the audible-tone feedback was convincing, particularly as-translated from front-plate treatments.
The other thing you could do, although I'm *very* hesitant to do this, based on safety considerations, would be to actually "de-reflectorize" the rear reflector.
fulcrum did this - http://www.radardetector.net/forums/laser-jammers/23293-how-important-rear-jammer-3.html - begin with post #24.
ahmadr
07-28-2008, 12:27 PM
I remain somewhat afraid at what an extreme-distance/angle "over the crest" shot might do, as it would stand to-reason that the bumper skin, protruding ahead of the jammer head, would cause line-of-sight interference under such conditions.
Judging from the pictures, he should be fine
http://www.radardetector.net/forums/laser-jammers/37051-extreme-angle-mounting-considerations.html
TSi+WRX
07-28-2008, 04:59 PM
+/- 11 vertically..... I dunno....when they're that recessed into his upper grill, with the bumper being right below it - that's my concern.
In my mind's eye, the jammer heads are essentially sitting right atop the top of the bumper - so what's below is efefctively blocked. Put the car nose-up on a slight rise or with the rear of the car settled into a big bump in the road (akin to the CFL's first testing session, where the red Magnum's front dipped into the roadway and produced PT, but "reverse" the scenario)....what happens then?
What's everyone ( you, particularly, ahmadr ;) ) thinking of as the best way to take some good measurements on our vehicles, to be sure we're not afoul of the divergence measures?
ahmadr
07-28-2008, 06:54 PM
+/- 11 vertically..... I dunno....when they're that recessed into his upper grill, with the bumper being right below it - that's my concern.
In my mind's eye, the jammer heads are essentially sitting right atop the top of the bumper - so what's below is efefctively blocked. Put the car nose-up on a slight rise or with the rear of the car settled into a big bump in the road (akin to the CFL's first testing session, where the red Magnum's front dipped into the roadway and produced PT, but "reverse" the scenario)....what happens then?
What's everyone ( you, particularly, ahmadr ;) ) thinking of as the best way to take some good measurements on our vehicles, to be sure we're not afoul of the divergence measures?
I may be mistaken, and it might be the camera angle, but from the photo, I feel the top of the bumper is heavily inclined (> 11 degrees).
11 degrees is close to a 20% slope. So for a 20 cm protruding bumper, a 4cm drop would be sufficient.
In contrast, some people want their jammers to have 180 degree visibility, but what I'm trying to say is that the heads, unfortunately, cover a very slim angle.
I'm in the middle of installing a single head on my car. And I'll have it completely level (vs slightly up), as the inclination will change if/when the car is fully loaded. Of course, I don't expect JTG performance, but I hope it's sufficiently close...
But if I had many jammer heads (like our dear TSi+WRX ;) ), I would install at least one of them verticaly, or maybe even incline some of them :D
MEM-TEK
07-28-2008, 11:59 PM
Hi guys,
My car's front bumper, just directly below the red rectangles, slopes downward at about 40 degrees. The bumper to either side of the red rectangles and next to the headlights slopes backward at about 20 degrees. Aside from the headlights, the bumper area in the general area where a front license plate gets attached has hardly any slope.
Today I sweated like a dog in the near 90 degree temperatures and did a lot of modifications to the installation. I also completed installing the radar antenna and routing all cables through the firewall. I decided to mount the shifters in the red rectangle positions. I also removed the grille work with the Hyundai logo and shot it flat black, and shot everything behind that grill work flat black too. I gave up shooting the area behind the bottom bumper air duct flat black since this would have required masking and I already was getting a terrific sunburn! In the late afternoon I parked the car in front of my house to get some shade. I caught a second wind, removed the instrument cluster, and mounted the remote display behind the clear plastic cover. Likewise I decided on a final mounting location for the control module. I mounted the control module just below the left side air vent since this location is within easy reach and is easily viewed by me while driving. Here are some photos! :)
Notice now how dark the area is where the shifters are located! I forgot to install the front license plate frame and cover which I painted flat black. That should really help kill reflections off the a big chunk of the front bumper area:
http://www.mem-tek.com/radar/reviews/9500ci/installation/Hyundai_front_new_1000x740.jpg
Here is a nice nighttime shot of the display module installed at the top of the instrument cluster. The display module is behind the instrument cluster's clear plastic cover:
http://www.mem-tek.com/radar/reviews/9500ci/installation/display_module_above_speedometer_1000x740.jpg
The control module mounted just below the driver's side left air vent. Its a cheap car. I didn't get fancy and use a drill or rotozip to make a really neat hole for the cable. Instead I just used nippy cutters to get 'er done:
http://www.mem-tek.com/radar/reviews/9500ci/installation/controller_below_air_vent_1000x740.jpg
Lucky225
07-29-2008, 12:25 AM
I would move the anteanna from driver side to above hyundai logo if at all possible. Other then that looks awesome. By concealed display did you just mean the regular display? I thought you meant the LED alert, did you install that too?
MEM-TEK
07-29-2008, 01:29 AM
I would move the anteanna from driver side to above hyundai logo if at all possible. Other then that looks awesome. By concealed display did you just mean the regular display? I thought you meant the LED alert, did you install that too?
The Hyundai logo it too big to move the radar antenna above it. Yet I would like to mount it perhaps on one side of the log, but this will require mounting the antenna vertical and fabricating a 45 degree reflector for the antenna. I think that I will conduct in-car tests with my STi using a prototype reflector so that I can establish the minimum necessary size for no degradation effects up to 30 degrees off-axis. You would think that it would be as simple as ray tracing the paths, but radar is funny when it strikes near the edges of metal surfaces. Likely a somewhat oversized reflector will be necessary.
Yeah, I meant the regular display. I was too dog tired to install the concealed display LED. That will have to wait until a cloudy day where I don't need SPF 30 sunblock!
:)
Lucky225
07-29-2008, 01:37 AM
Lazy bastard ;) hahaha j/k I've worked on this SRX in all types of harsh weather, Arkansas, Texas and California heat, it sucks, I know, after 2 installs and at least 3 fixes... and I know as soon as my Rj-22 jacks arrive in the mail, it'll prolly still be 110 here in TX when I go to fix it for the 4th or whatever time this is.
focalcivic
07-29-2008, 09:17 AM
Can you post an extanded view of the dash showing the switch and display?
TSi+WRX
07-29-2008, 12:29 PM
I may be mistaken, and it might be the camera angle, but from the photo, I feel the top of the bumper is heavily inclined (> 11 degrees).
11 degrees is close to a 20% slope. So for a 20 cm protruding bumper, a 4cm drop would be sufficient.
and
My car's front bumper, just directly below the red rectangles, slopes downward at about 40 degrees. The bumper to either side of the red rectangles and next to the headlights slopes backward at about 20 degrees. Aside from the headlights, the bumper area in the general area where a front license plate gets attached has hardly any slope.
^ Looks like you're good-to-go, if I'm reading both of these correctly. :)
In contrast, some people want their jammers to have 180 degree visibility, but what I'm trying to say is that the heads, unfortunately, cover a very slim angle.
Ah! I see what you're saying. A distinction between reception, and output, correct? Good point.
I'm in the middle of installing a single head on my car. And I'll have it completely level (vs slightly up), as the inclination will change if/when the car is fully loaded. Of course, I don't expect JTG performance, but I hope it's sufficiently close...
What I also have a slight fear about is just that, what happens to my leveling after I sit my fat butt in the car. :o
But if I had many jammer heads (like our dear TSi+WRX ;) ), I would install at least one of them verticaly, or maybe even incline some of them :D
I've thought about doing that (vertical) with my LPP heads, but alas, my grill is less-than accommodating in that manner, and I'd have to pursue more extensive modification.
In terms of mounting on a slight incline, the LPP heads are ever-so-slightly bubble-positive - my "virtual-compensation" for my sitting in the car, as well as for other times when I might be "nose down." For the LIs, I've left them true-level, as I hope to achieve "best odds," since they're my primary line of defense.
With the ZR3s, in order to maximize their detection/reception capability, I actually do have them pointed "out" towards each respective side of the vehicle, just a little. :)
Same for the rear. The LPP head is actually slightly bubble-positive, hoping to better position itself against threats from slightly elevated positions, as-typical of, say, an on-ramp enforcement scenario.
But honestly, while I know that the front ZR3 setup does give me some rather shocking capability to capture scatter/reflections, my rear setup with the LPP head is just "shooting-in-the-dark." I don't know if it really is of any benefit, and I know that it is not nearly as beneficial for actual end-on rear shots (for which, I hope, the two LI heads back there, in being true-level, will take care of). :)
Today I sweated like a dog in the near 90 degree temperatures and did a lot of modifications to the installation.
:lol:
I'm a polar bear, so while my friends all ***** about not liking to work when it's snowy outside, and the concrete floor in their garage ice-cold, I rather hate to work when it's even just above 70-deg. (F., of course! :eek::D) outside.
Notice now how dark the area is where the shifters are located! I forgot to install the front license plate frame and cover which I painted flat black. That should really help kill reflections off the a big chunk of the front bumper area:
Looks good!
Be sure to also spray/cover your plate-fastening hardware, or use non-metallic (i.e. nylon) fasteners! If you can't find the nylon screws, have a look around the plate-covers/frames area in your local automotive parts retailer, and you should find plate frame/cover combos which offer a plastic cover that goes over the fastener screw, and make it cosmetically blend with the plate frame. You can paint this cover to-match, which is what I've done (I used to use nylon fasteners there, but I'd managed to shear their heads off a couple of times, so I switched to standard metal fasteners, covered by such a cosmetic flap to cut laser reflection).
Also, is there a way for you to keep an eye on water temperature?
I notice you've sprayed the top half of the radiator (or is that your A/C?).....
The reason I ask is because there's always discussion in the "tuner" community about spray-painting an intercooler, chiefly for aesthetics - and always, the worry turns to heat-exchange.
Interior looks great!
Try a little dab of black RTV-silicone to "seal" that hole that the control unit trails. Just a dot, I think, would fill it, and you can also shape it to best cosmetic ends. I don't think that you could find a grommet small enough to do the same.....
MEM-TEK
07-29-2008, 01:46 PM
Also, is there a way for you to keep an eye on water temperature?
I notice you've sprayed the top half of the radiator (or is that your A/C?).....
The reason I ask is because there's always discussion in the "tuner" community about spray-painting an intercooler, chiefly for aesthetics - and always, the worry turns to heat-exchange.
My car's A/C evaporator is mounted in front of my car's radiator. The evaporator is what I spray painted flat black. Of note, when you paint a surface black, then (assuming that the paint has a good bond to the surface) you effectively turn the surface into a black body radiator. If anything, the flat black paint will increase the efficiency of my car's A/C evaporator. By nature a black colored surface has to efficiently radiate infrared heat throughout the entire deep infrared portion of the electromagnetic spectrum. I'm not worried about IR laser reflecting from the black painted surfaces since 904nm is barely into the IR. A fair amount of the IR laser energy will be absorbed and then re-radiated at even longer IR wavelengths which we feel as heat radiating off of a surface. Such is the nature of black body radiators. This by the way also explains why black colored radar detectors, especially when mounted not too far above a dark or black colored dash, get extremely hot and literally roast in sunlight.
:)
djrams80
07-29-2008, 10:47 PM
The install is very nice Michael. Your reception should be very good with the radar antenna mounted just where it is. Again, congratulations on your 9500ci. :D
rsatmans
07-30-2008, 01:01 AM
Looks great :) I really like your antenna mounting location. I feel that is the best location due to it being high, having a clear view, and closer to the middle of the road. Although in controlled testing environments antennas work best mounted in the middle (which is not possible in your case) in the real world you usually have traffic in front of you which can block a weak signal. If a detector has a better line of sight it has more possibility of picking up the radar.
TSi+WRX
07-30-2008, 07:24 AM
My car's A/C evaporator is mounted in front of my car's radiator. The evaporator is what I spray painted flat black.
Cool beans. :) No pun intended. :p
Of note, when you paint a surface black, then (assuming that the paint has a good bond to the surface) you effectively turn the surface into a black body radiator. If anything, the flat black paint will increase the efficiency of my car's A/C evaporator. By nature a black colored surface has to efficiently radiate infrared heat throughout the entire deep infrared portion of the electromagnetic spectrum. I'm not worried about IR laser reflecting from the black painted surfaces since 904nm is barely into the IR. A fair amount of the IR laser energy will be absorbed and then re-radiated at even longer IR wavelengths which we feel as heat radiating off of a surface. Such is the nature of black body radiators. This by the way also explains why black colored radar detectors, especially when mounted not too far above a dark or black colored dash, get extremely hot and literally roast in sunlight.
:)
That's a part of what's been said on the various Forums.... If I have some spare time today, I'll do some digging, and see if I can't find what someone else had to say as a counterpoint to that argument. I'd never looked much into it, as I've not really considered putting coatings on my intercoolers, but there was a lot of back-and-forth on such issues - not just in terms of color, but the actual material sprayed onto the fine fins of the intercooler, and the way in which such differences may affect exchange efficiency (and then, of course, the debate took a side-turn, which was, of course, the usual - as to if there were any significant differences in terms of actual loss/gain, you know, the usual car-guys' debate :o).
ahmadr
07-30-2008, 10:53 AM
If anything, the flat black paint will increase the efficiency of my car's A/C evaporator. By nature a black colored surface has to efficiently radiate infrared heat throughout the entire deep infrared portion of the electromagnetic spectrum.
:bs2: :D
Not necessarily. A black painted radiator will more effectively radiate heat, but less effectively conduct heat to the air flowing through it, depending on the paint thickness. And most of the heat transfer is through conduction to the air flowing through it.
focalcivic
07-30-2008, 11:05 AM
Mem, can you take a pic of dash with a further view showing the display module and the control switch?
MEM-TEK
07-30-2008, 01:44 PM
Here are some better pictures of where I installed my 9500ci's display and control modules.
http://www.mem-tek.com/radar/reviews/9500ci/installation/display_module_above_speedometer1_1000x740.jpg
http://www.mem-tek.com/radar/reviews/9500ci/installation/controller_below_air_vent1_1000x740.jpg
http://www.mem-tek.com/radar/reviews/9500ci/installation/controller_below_air_vent2_1000x740.jpg
AirMoore
07-30-2008, 04:00 PM
Very nice... the only thing I might suggest is where the Control Box(module) comes out (where the cord does rather), buy a small black grommet, and drill a hole there (or round the edges so u don't have to make it bigger), it will give it a much 'cleaner' appearance IMO compared to where it seems like its broken/snapped like a mouse-hole where it comes out. (Just my $.02)
Overall: Very nice clean install, and I can't wait to see pictures of the opened ZR4 heads.
focalcivic
07-30-2008, 07:15 PM
Thanks Mem, that gives it a better perspective. Does the display bother you that it blocks the top of your Speedo?
As a side note i can not believe Escort did not put the power button in a different spot to allow for flush mounting.
MEM-TEK
07-30-2008, 08:06 PM
Thanks Mem, that gives it a better perspective. Does the display bother you that it blocks the top of your Speedo?
As a side note i can not believe Escort did not put the power button in a different spot to allow for flush mounting.
Your welcome! I thought about mounting the display a bit more forward so that it wouldn't block the very top of my speedometer, but I decided on mounting it where it is so that it can't be seen unless you lean your head into my car window. I have the 9500ci set to always display my vehicle speed when it is not alerting. Its really cool to just have to look at the display to know my speed. I have some white electrical tape. I am thinking about cutting some thin strips and sticking them on the speedometer dial so that I will have tick marks for 65, 70, and 75 mph.
Yeah, I thought the same thing when I saw that the power button is on top of the control module. The module snaps apart easily though. I plan to take a picture of its internals, check to see if there are inline resistors for the power button, check to see where two leads can be soldered in, and figure out an easy yet totally safe way to wire in a separate remote power button. The power button is nothing more than a momentarily closed switch. Anyway, a separate power button would allow the control module to be flush mounted by a creative installer. Yet a remote power button isn't even really necessary since the 9500ci does remember whether or not it was powered off before power to the system is killed either by turning off your ignition or by a separate power switch on the 9500ci's 12 volt power wire.
Instead of the button modification, it might even be more cool to simply mount the control module on my driver door's armrest. Now that would be really convenient!
:)
MEM-TEK
07-30-2008, 08:12 PM
Very nice... the only thing I might suggest is where the Control Box(module) comes out (where the cord does rather), buy a small black grommet, and drill a hole there (or round the edges so u don't have to make it bigger), it will give it a much 'cleaner' appearance IMO compared to where it seems like its broken/snapped like a mouse-hole where it comes out. (Just my $.02)
Overall: Very nice clean install, and I can't wait to see pictures of the opened ZR4 heads.
I may scrape some plastic from a hidden and inconspicuous area of my dash, grind it up and mix it with a bit of epoxy, and then fill in the gaps after placing an appropriately sized drill bit wrapped with some tape in the hole. Once the epoxy sets, I simply yank out the drill bit, tear off any tape which is sticking out, and put the controller wire back in place. It should look virtually perfect then.
I will open and photograph the ZR4 heads within the next few days. :)