PDA

View Full Version : ZR4 on the way. How to cut grill?



Z1NONLY
07-29-2008, 05:18 PM
So the wife and I added another car to our "fleet" that should get almost twice the gas milage of either of our other cars.

My wife only agreed to buy the jammer if I installed it.

So I think I need to cut my grill.
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7757.jpg

I was thinking of using a file. Anyone have a better idea that will render good-looking, yet effective, results?

I intend to mound the heads in the outside parts of of the "top" grill, near the headlights.


***update*****

All done! I ended up using the cutting (drill) bit in my rotatry tool.

First I took the X50 Rev.5 out of my work van and hardwired it in th tC.
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7770.jpg


She hates radar detector "sounds" so I installed the hardwire kit with the flashing red light in plain view.
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7769.jpg



The ZR4 install was a pain in the @$$, just as I thought it would be. But my brother and I took our time and I think it turned out well. (He got stuck with getting the cables through the firewall and I got stuck with... everything else.:p

The display..
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7764.jpg



The front heads are not as "stealth" as I wanted but they don't draw too much attention.
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7760w.jpg
A closer shot..
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7761.jpg



Down shot...
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7772.jpg



I expected the rear shifter to be easy and mounting was. But getting the wire from the hatch to the car in a manner that wouldn't cause water problems was a pain.
http://i270.photobucket.com/albums/jj117/Z1NONLY4REAL/100_7771.jpg

Stealth Stalker
07-29-2008, 05:49 PM
Dremel ftw!

Of course, I have to say it would be wildly ironic to use a laser to cut with! :lol:

Laser-InterceptorUSA
07-29-2008, 06:02 PM
Traitor! :p

Cliff - C55

Z1NONLY
07-29-2008, 06:12 PM
Traitor! :p

Cliff - C55

:D

I know LI is the "king of the hill", but I intend to add a 9500ix and be "done" with it. All for less than $1k (The wife hates falses and she's the one driving it most of the time.)

It's a small, dark car, so the poor little LED heads shouldn't have to work too hard. (I hope):o

Lucky225
07-29-2008, 06:25 PM
LOL I hear you, wife doesn't drive but she hates gadgets, so 9500CI for me and 'be done with it'... less falses = less her tripping out on sounds and whistles

focalcivic
07-29-2008, 07:53 PM
Get a Dremel with a cut off wheel.

TSi+WRX
07-30-2008, 07:17 AM
+1 to Dremel (-type tool).

If you're unfamiliar with such tools, then get some practice material to cut - you'll get the hang of it very fast, if you're at all mechanically inclined. :) Remember, let the speed of the tool do the work. The fiberglass-reinforced super-heavy-duty cutoff wheels may be too big in size for you to use, but I can't be sure, without seeing the grill first-hand.

Clean up the cut(s) with a small, fine file or some Emory-paper.

Also, I'm not sure how the aftermarket is for the Scion. I'd bet that it's pretty decent. You may be able to source an aftermarket grill off eBay or the like, or join one of their enthusiast communities and get a take-off OEM replacement from another member.

:)

thestaton
07-30-2008, 08:33 AM
Start shopping for a replacement grill immediately. That way if you screw it up, you'll have one sitting in your garage.

Dremels are the bomb, and it looks like it's a nice area to work with. If anything see if you can't pop that grill out.

Also, I'm not sure if you have noticed but if you got the CI you need to make a hole for the CI antenna as well.

hockey005
07-30-2008, 09:04 AM
get some veil g4 and a laser shield as well

TSi+WRX
07-30-2008, 09:36 AM
Start shopping for a replacement grill immediately. That way if you screw it up, you'll have one sitting in your garage.

Dremels are the bomb, and it looks like it's a nice area to work with. If anything see if you can't pop that grill out.

Also, I'm not sure if you have noticed but if you got the CI you need to make a hole for the CI antenna as well.

Like the man said, pop the grill out, if at all possible.

That'll make it 10x easier to work with. :)

Z1NONLY
07-30-2008, 06:54 PM
I have a rotary tool, but I have never used it. I guess I will try it out this weekend.

focalcivic
07-30-2008, 07:07 PM
I have a rotary tool, but I have never used it. I guess I will try it out this weekend.


Do you have a cut off wheel? I would practice first spare piece of plastic or wood.

Z1NONLY
07-30-2008, 07:14 PM
Do you have a cut off wheel? I would practice first spare piece of plastic or wood.

Without removing the grill, I can't see how to use the wheel. Other parts of the bumper won't let me have a right-angle, and the plastic is about 1/2" deep.

Whatever I do, I will end up using a file at some point....

AirMoore
07-30-2008, 07:45 PM
Whatever I do, I will end up using a file at some point....

Good idea...
Its better to do its 'old-school' and gentle with that, then to ruin the whole install by trying to save time&effort and mauling it with a power-tool. For the details, id stick with using a nice hand-file system.

fire65
07-30-2008, 08:01 PM
If you can't get the dremel to it, you might try a hacksaw blade. Take it out of the saw, the fine teeth will work well and leave a smooth finish.

MEM-TEK
07-30-2008, 08:30 PM
I used a Popular Mechanics tool which is like a hacksaw blade, except that the blade height is approximately 3/4 inch and more like a large knife, and it has a large handle. Its really sturdy and it allows you to make carefully controlled cuts on plastic. On the other hand, it looks like the top grille on Z1NONLY's car is recessed about 1 inch. I would simply use 3M VHB tape from Radio Shack, stick the ZR4 mounting brackets to the bottom plane of the top grille surround, mount the shifters in the brackets, and be done with it. Recessing the heads into the front grille would look really clean and cool, but is this really necessary?

Z1NONLY
07-30-2008, 08:54 PM
I used a Popular Mechanics tool which is like a hacksaw blade, except that the blade height is approximately 3/4 inch and more like a large knife, and it has a large handle. Its really sturdy and it allows you to make carefully controlled cuts on plastic. On the other hand, it looks like the top grille on Z1NONLY's car is recessed about 1 inch. I would simply use 3M VHB tape from Radio Shack, stick the ZR4 mounting brackets to the bottom plane of the top grille surround, mount the shifters in the brackets, and be done with it. Recessing the heads into the front grille would look really clean and cool, but is this really necessary?

You can't tell by the picture, but the bottom plane of the top grille surround is not that wide and is rounded with a downward slope.

Behind the grill is what looks like a steel cross-member with about a 3 inch wide, flat, level surface. Mounting the brackets to this should make the heads come out at the bottom of the black part of the upper grill. (It my be just a tad low. I may need some sort of spacers.)

This will be a bit of a PITA, but I should have the time, and I only want to do this once.

TSi+WRX
07-31-2008, 07:37 AM
I would practice first spare piece of plastic.....

Go for plastics. :)

This way, you'll get an understanding of the "speed as cutting tool" idea, as well as understand how your cuts may create "melts" in the material, as well as get used to the bits of tiny (and hot) plastic burrs that fly up at you. :p

Wear eye protection.

MEM-TEK
07-31-2008, 10:05 AM
Perhaps a variable speed jig saw with a thick yet fine toothed blade will do the trick.

Z1NONLY
07-31-2008, 05:12 PM
The ZR4 is here!

I think I can use the new mounting brackets to avoid drilling any metal. The "clamps" look like they will fit into the holes above the cut-out area I intend to make. Then it's justa question of leveling.

I guess I can use the back of the head's flat surface for that?

focalcivic
07-31-2008, 11:41 PM
The ZR4 is here!

I think I can use the new mounting brackets to avoid drilling any metal. The "clamps" look like they will fit into the holes above the cut-out area I intend to make. Then it's justa question of leveling.

I guess I can use the back of the head's flat surface for that?

Don't forget that they need to clamp onto something then tighten down.

Another thing, after you make the cut, if you have a nice flat surface you might be able to use mounting tape to make life easier.

TSi+WRX
08-01-2008, 07:25 AM
Perhaps a variable speed jig saw with a thick yet fine toothed blade will do the trick.

Screw that!


http://www.devicelink.com/expo/awards/awards/07/031-Stryker-Precision-Saw01_150p.jpg

:lol:

No, seriously, your idea isn't a bad one at all, MEM-TEK.

Z1NONLY
08-02-2008, 03:51 PM
It's all installed!

I ended up using my rotary tool, and the cutting (drill-looking) bit.

Pictures of the completed install are now updated on the first page/post of this thread.:)

thestaton
08-02-2008, 04:44 PM
beautiful install. that's a good feeling when you sit on the pavement and take the final install pics.

focalcivic
08-02-2008, 08:10 PM
Nice install, I guess you could not get the heads a tad further in the grill?

Also, I am not crazy about the shifter display placement, I think it would of looked better in the center stack maybe in one of the pockets. (please don't take this as critism, just my opinion).

I noticed in your gauge display you have the direct wire still attached, did you link the shifter to the detector?

Z1NONLY
08-02-2008, 08:24 PM
Nice install, I guess you could not get the heads a tad further in the grill?

Also, I am not crazy about the shifter display placement, I think it would of looked better in the center stack maybe in one of the pockets. (please don't take this as critism, just my opinion).

I noticed in your gauge display you have the direct wire still attached, did you link the shifter to the detector?

The grill has an arc to it, so I had to put the inside clamps as far back as possible and the outside clamps had to be mounted more forward, so the heads would point straight ahead.

This is the wife's car, so I had to defer to her requests. I wanted to put the ZR4 display in the center stack, but she uses that cubby a lot and didn't want anything to limit access. So we settled on the side mount.

Also, I would have preferred to link the X50 and the ZR4, but my wife hates audio alerts from radar detectors and has been spoiled by the remote red led (on her SRX) that alerts her in her other car. For this reason I used the hardwire kit and mounted the remote display in her line-of-sight. She will run the X50 with the volume at "0" and only use the light for alerts.

MEM-TEK
08-02-2008, 11:25 PM
I think that the front shifter install looks splendid! I wouldn't try to mount the front shifter heads any further back in the grille. :)

TSi+WRX
08-03-2008, 09:49 AM
I agree with MEM-TEK and thestanton - that's a great install, particularly given the noted preferences of your wife, the primary driver of that vehicle.

Good stuff, thanks for sharing! :)

Z1NONLY
08-03-2008, 10:10 AM
Thanks.


Did anyone notice my green-power-light "delete"?

In her Magnum, we found the green power-on light too bright at night. So I just cut one of the leads on the Bi-color LED and disabled "green". The SRX main display was all we needed to know that the unit was "on".

In the tC, I simply covered the (separate) green light with a small piece of black electrical tape.

Crude, but effective.:p