View Full Version : 3m protective headlight film on headlights
eviltwin67
08-24-2005, 07:58 PM
I will be installing 3m protective headlight film on my headlights. Do I put Veil on the lenses and then put the film on top or Veil the film on top of the lens? thanks
StKnoWhere
08-24-2005, 08:40 PM
Since the adhesive might not stick well to the a veil coated headlight, I suspect you would want it on top of the film but someone else may know better.
It would be interesting if headlight film were available with Veil embedded in the film.
Veil Guy
08-24-2005, 09:41 PM
eviltwin67,
It would be most efficient to have VEIL on the outer side of the coating.
StKnoWhere,
We have a number of new developments in the works which, I am afraid, I am not in a position to discuss at this time. When the time comes, you guys will most certainly be one of the first to hear about them. :wink:
Veil Guy 8)
StKnoWhere
08-24-2005, 10:19 PM
Veil Guy says:
We have a number of new developments in the works which, I am afraid, I am not in a position to discuss at this time. When the time comes, you guys will most certainly be one of the first to hear about them.
.. that's why the call me St. KnoWhere :wink:
When I first learned about your product a week ago a number of (probably not new) possibilities occurred to me. The thought of something like an IR absorbing lens cover and/or clear bra material would be a dynamite product.
I wish you luck with your development whatever it may be!
squonk
08-25-2005, 12:15 AM
ya know..............not to jack this thread.........but kinda along the same lines. I was thinking.......what if the license plate was angled back a little bit.........or........if the plate was loose enough so that it would swing a little bit back and forth. I dont know if there is a law concerning that but I think that would make it a bit harder to get a lidar reading off the plate .......no?
thestaton
08-25-2005, 06:16 AM
squonk: maybe seth can take a picture of his plate but he keeps his angled and uses his plate covers angled too! if i remember correctly!
JNewell
08-25-2005, 08:21 AM
Funny this should come up. I've had the 3M film on my headlights for several years and am looking at installing Veil.
VG, do you know whether the Veil will affect the adhesion of the 3M film, and whether there are any other performance issues putting Veil on top of the film? Thanks!
Longsnowsm
08-25-2005, 08:44 PM
On my motorcycle I have the 3m adhesive cover on my headlight and I Veiled over the top of it. So far no problems.
Drive safe, have fun,
Longsnowsm
spankyaf
08-30-2005, 10:15 AM
Longsnowsm, Can you take the film off easily and then reinstall it? My night eyesight is bad and I'd like the option of removing the Veil to keep maximize the light output.
I've never heard of this stuff before but very interesting!!! Would I be correct in assuming that I could use it and now apply Veil to the painted surfaces of my bike and car.
http://www.webbikeworld.com/t2/motorcycle-paint-protection/
Longsnowsm
08-30-2005, 04:43 PM
No, I don't think I could remove the 3m without the Veil cracking and flaking. I understand where your coming from on the night driving. It seems to depend on the vehicle as to how much light output is affected by Veil. On one car I put Veil on the light output was affected a lot. On the car I drive day to day it didn't seem to affect it hardly at all. So what some have said that it doesn't affect light output it really seems to depend on the vehicle it is applied to.
Longsnowsm
jwardell
01-23-2007, 01:32 PM
I've searched but I haven't found a clear response or not, so I'll bump this topic and ask clearly:
Is it OK to apply veil over clear bra film protected headlights?
All my lights have it and I would like to get veil, but as the headlight film is thick (thicker than clearbra film that goes on the hood/bumper) and possibly has a slight texture to it, i can imagine it having issues similiar to license plates.
Also the veil guy hinted at "new products" related to this topic back in march, and continues to hint at new formulations more recently...but still has no details.
I can't apply till the weather warms up in a few months anyway so I guess it's in my best interest to wait, but I might as well ask the questions sooner than later.
quandary
01-23-2007, 08:23 PM
If you are going to put 3M film on your headlights, ask your vendor if they can get you the film that also blocks infra-red. 3M has many different types of film for this purpose. Assuming he can get you some, you will not need Veil.