PDA

View Full Version : LI external speaker + misc stuff



th3 factory freak
09-24-2008, 01:08 AM
So my LI's CPU is totally hidden and I decided an external speaker is needed.

Per the manual, I do see the speaker has be at least 1 WATT and between 16-32 Ohms.

Any recommandations for a good speaker and where to get it?

I thought of a circular, 3 inch speaker but can't find one.


2. I forgot the hook up the leads for the switch, so the light isn't turning on when the system is active.

Does it matter which wire goes to which lead on the switch?

3. When I turn on the system, it says "welcome". Now the first time I turned it on, it did the Phone beep beep sounds and then said the parking aid is de-activated.

Now it just says welcome and after 10 seconds it says the parking aid is de-activated, but there is no beep beep phone sound, is that normal?

Laser-InterceptorUSA
09-24-2008, 05:30 AM
So my LI's CPU is totally hidden and I decided an external speaker is needed.

Per the manual, I do see the speaker has be at least 1 WATT and between 16-32 Ohms.

Any recommandations for a good speaker and where to get it?

I thought of a circular, 3 inch speaker but can't find one.


2. I forgot the hook up the leads for the switch, so the light isn't turning on when the system is active.

Does it matter which wire goes to which lead on the switch?

3. When I turn on the system, it says "welcome". Now the first time I turned it on, it did the Phone beep beep sounds and then said the parking aid is de-activated.

Now it just says welcome and after 10 seconds it says the parking aid is de-activated, but there is no beep beep phone sound, is that normal?

Any good communications speaker will work. Check the Internet for Ham Radio Stores.

Yes, the position of the wires is indeed critical and you do not want to damage your CPU and void your Warranty so call me today at the office and I'll guide you through reassembling your connectors on your switch. 352-688-0708.

The Voice Alerts you heard upon powering up your LI are correct and indicate that your LI is indeed functioning normally and are in the following order:

1) "Welcome" - for 15 seconds, the PA (Parking Aid) is now active. The beeping is the sensors detecting an object within the proximity range programmed into your LI from the factory. If the sensors are close enough to an object, wall, other vehicles etc, it will indeed beep. If not, you will not hear the PA beeps.

2) "Parking Aid is Deactivated" Your LI is now in the Jamming Detection mode and is fully active.

I hope this helps? Please call me to get your switch squared away!

Thanks!

Cliff - C55

muledoe1
09-24-2008, 08:19 AM
has anyone actaully connected it to the radio mute? I rather do that then get a speaker n stuff. im kinda scared to try it tho lol

Laser-InterceptorUSA
09-24-2008, 08:26 AM
has anyone actaully connected it to the radio mute? I rather do that then get a speaker n stuff. im kinda scared to try it tho lol

NOT recommended! I have already replaced two CPU's because LI Users connected the output of the LI Speaker to their vehicles Active stereo dumping 200 to 1200 watts into the LI. This is NOT covered by the LI Warranty!

With that said, I suggest you either mount the CPU in close proximity to your driving position, mine is mounted under my steering column and is very audible, or provide a dedicated speaker for your LI.

Cliff - C55

focalcivic
09-24-2008, 10:39 AM
NOT recommended! I have already replaced two CPU's because LI Users connected the output of the LI Speaker to their vehicles Active stereo dumping 200 to 1200 watts into the LI. This is NOT covered by the LI Warranty!

Cliff - C55

I guess they did not hook it up correctly, when using the mute wire you will need a mute lead off your radio, typically many aftermarket radios have this wire.

As for the switch wiring, in the LI owners manual you will see a wiring diagram to the switch, that is helpful to get the wires in the proper spot, but look very closely at it the + and - is very hard to see, or just call Cliff as he said.

The thing about the external speaker hookup, if memory serves me correct there are 2 wires for speaker and the same color? I never know how to hook it up? I know you have to change the jumper inside.

Laser-InterceptorUSA
09-24-2008, 10:44 AM
Yes, the two blue wires are the EXTERNAL SPEAKER hook-up. You can find the info in the LI User's Manual regarding the INT/EXT Speaker jumper.

The MUTE is a Negative pull-down. if your car's radio requires a POS pull-down, you'll need a relay to achieve this.

Cliff - C55

maty j
09-24-2008, 02:19 PM
How loud Is the LI? I know, difficult question to answer but a blinder for instance Is really easy to hear even with stero pumping, Not that I have It loud very often. Is It adjustable volume too??

Laser-InterceptorUSA
09-24-2008, 02:35 PM
Maty,

I commonly drive with my windows down, at above PSL, usually listening to talk radio and never have a problem hearing the LI Voice Alerts with my CPU mounted next to my steering column and facing down towards my floor board with the volume adjusted to at Max.

I hope this answers your query?

Cliff - C55

maty j
09-24-2008, 04:24 PM
Yes, Thanks Cliff. Just with the talk of extra speakers and stereo muting I thought It would quite quiet.
Cheers,

Laser-InterceptorUSA
09-24-2008, 04:29 PM
Maty,

You know Yanks and their Wanks! :rolleyes:

Cliff - C55

maty j
09-24-2008, 04:43 PM
:crazy_pilot:http://www.radardetector.net/forums/370089102157

Laser-InterceptorUSA
09-24-2008, 04:47 PM
How did the Tommy Trinder saying go?

"overpaid, overfed, oversexed and over here?" :D

We Americans LOVE over-kill!

Cliff - C55

maty j
09-24-2008, 04:55 PM
There has been a series on fishing on our TV chanels over here and on one episode the presenter went fishing with a couple of americans. Not normal fishing though, American stlye on a hovercraft that the people on board needed ear defenders and insted of a rod they had a gun. I was suprised when they didn't "catch" lol.

They were also bow fishing carp which looked great fun but most anglers and owners over here wouldn't be too impressed If I were to go bow fish myself some carp!

th3 factory freak
09-24-2008, 06:00 PM
Any good communications speaker will work. Check the Internet for Ham Radio Stores.

Yes, the position of the wires is indeed critical and you do not want to damage your CPU and void your Warranty so call me today at the office and I'll guide you through reassembling your connectors on your switch. 352-688-0708.

The Voice Alerts you heard upon powering up your LI are correct and indicate that your LI is indeed functioning normally and are in the following order:

1) "Welcome" - for 15 seconds, the PA (Parking Aid) is now active. The beeping is the sensors detecting an object within the proximity range programmed into your LI from the factory. If the sensors are close enough to an object, wall, other vehicles etc, it will indeed beep. If not, you will not hear the PA beeps.

2) "Parking Aid is Deactivated" Your LI is now in the Jamming Detection mode and is fully active.

I hope this helps? Please call me to get your switch squared away!

Thanks!

Cliff - C55

Cliff, yes it does help. Sorry I'm very busy at work today, I will call you tomorrow.

FoolishOne
09-24-2008, 07:35 PM
Maty, dj has a video up and it's pretty loud, in my opinion, especially towards the end, that you might take a peek at, if you haven't already.

http://www.radardetector.net/forums/detector-counter-measure-videos/38864-v1-li-laser-false-alerts.html

maty j
09-25-2008, 05:19 AM
Cheers mate, Seems like It would be loud enough for me :cool:

dorcse
09-25-2008, 05:27 AM
I use this with great results (loud and quite clear):

Uniden Model ESP5 (A 5-Watt CB Speaker. Just do a search for it).

Ed

Aoshi
09-25-2008, 09:47 AM
Being the cheap person that I am, would it be possible for the LI to share my STi-R's speaker?

Has anyone else tried this?

Laser-InterceptorUSA
09-25-2008, 09:51 AM
Read down in the thread a bit. The LI must have a dedicated speaker. Several well meaning LI users connected the EXT Speaker provision to their 200W - 2000W Stereos and toasted the LI CPU. This is NOT covered by Warranty!

Cliff - C55

TSi+WRX
09-25-2008, 10:24 AM
"overpaid, overfed, oversexed and over here?" :D

Hey, I resemble that statement! :p

Aoshi
09-25-2008, 05:56 PM
Read down in the thread a bit. The LI must have a dedicated speaker. Several well meaning LI users connected the EXT Speaker provision to their 200W - 2000W Stereos and toasted the LI CPU. This is NOT covered by Warranty!

Cliff - C55

I'm not interested in hooking it to the stereo speakers, the STi-R speaker is a small, powered speaker and would be easy to splice and use. I'm curious if anyone has done this yet, and if not, why not?

muledoe1
09-26-2008, 07:44 AM
ok so no direct hook up to car. next question is it possible to get a external speaker hook it up then when u are being hit somehow mute the stock radio when LI is alerting. reason I ask I drive with music high. couple weeks ago I was being hit for several seconds and didn't even notice till I passed him. I look at my li lights and it was just blinking. :-(.

Laser-InterceptorUSA
09-26-2008, 07:57 AM
ok so no direct hook up to car. next question is it possible to get a external speaker hook it up then when u are being hit somehow mute the stock radio when LI is alerting. reason I ask I drive with music high. couple weeks ago I was being hit for several seconds and didn't even notice till I passed him. I look at my li lights and it was just blinking. :-(.

Yes, there is a MUTE Negative wire on the Li Power Loom. Specific information is available in the LI User's Manual.

Cliff - C55

mrcllusb
09-26-2008, 12:18 PM
Hmmm.How come LI doesn't offer and external speaker as an extra option?I understand that the internal speaker may be good enough,but hey it's a valuable option that customers will pay for.

muledoe1
09-26-2008, 06:45 PM
Yes, there is a MUTE Negative wire on the Li Power Loom. Specific information is available in the LI User's Manual.

Cliff - C55

Thank you, sorry i never got the manual :(. And also im not that great that wiring stuff like that. I get scared im gonna fry something

Laser-InterceptorUSA
09-27-2008, 06:30 AM
Remind me please a day before the meet and I will gladly provide you with an LI User's Manual! :)

Cliff - C55

focalcivic
09-27-2008, 12:56 PM
Remind me please a day before the meet and I will gladly provide you with an LI User's Manual! :)

Cliff - C55

Isn't the manual online?

Engel
10-01-2008, 10:07 AM
I have a speaker from a escort sr7, that would work for LI correct?

Laser-InterceptorUSA
10-01-2008, 10:22 AM
Hi Engel,

I do not know the Specs on that particular speaker but I suspect it will fit the bill. Ideally, you want a 4-16 Ohm and up to 5 Watt capability.

Cliff - C55

muledoe1
10-01-2008, 01:30 PM
Hi Engel,

I do not know the Specs on that particular speaker but I suspect it will fit the bill. Ideally, you want a 4-16 Ohm and up to 5 Watt capability.

Cliff - C55

Cliff, what speaker would you recommend then?

Laser-InterceptorUSA
10-01-2008, 02:35 PM
Cliff, what speaker would you recommend then?

Any small speaker within those specs that will fit in your intended mounting area.

Cliff - C55

muledoe1
10-01-2008, 05:10 PM
i understand that lol but i was kinda of looking for a certain brand maybe that you have used and trust and like. Just something really small thats all.

Laser-InterceptorUSA
10-01-2008, 05:28 PM
i understand that lol but i was kinda of looking for a certain brand maybe that you have used and trust and like. Just something really small thats all.

Sorry. No specific brand but you may wish to start with a Retailer of Ham/Amateur Radio Equipment like Kenwood, Yaesu or Icom as well as Alinco.

Cliff - C55

muledoe1
10-01-2008, 09:43 PM
maybe something like
this (http://cgi.ebay.com/External-speaker-4-ohm-for-YAESU-etc-Mini-Size_W0QQitemZ220287370933QQcmdZViewItem?hash=item 220287370933&_trkparms=72%3A1205%7C39%3A1%7C66%3A4%7C65%3A12%7C 240%3A1318&_trksid=p3286.c0.m14#ebayphotohosting)

only this is, do u have to cut the end off and splice them? or what?

Laser-InterceptorUSA
10-02-2008, 04:14 AM
Excellent choice! Yes, just cut off the connector and splice it to your LI's blue speaker wires. Be sure to remember to open the CPU and move the EXT/INT Speaker Jumper to the EXT position! :)

Cliff - C55

muledoe1
10-02-2008, 05:05 PM
Excellent choice! Yes, just cut off the connector and splice it to your LI's blue speaker wires. Be sure to remember to open the CPU and move the EXT/INT Speaker Jumper to the EXT position! :)

Cliff - C55

ok, if i get it on time ill bring it to the meet. Also you have to show me how to mute the car stereo when the alert goes off with the external speaker.

Thanks

Laser-InterceptorUSA
10-02-2008, 05:12 PM
ok, if i get it on time ill bring it to the meet. Also you have to show me how to mute the car stereo when the alert goes off with the external speaker.

Thanks

The black wire from the LI's wiring Loom is used as a Negative Pulldown for your car's stereo. You will need to your stereo accessible to do this. If you stereo is indeed accessible then, I'll be more than happy to assist you with this. :)

Cliff - C55

muledoe1
10-02-2008, 07:25 PM
The black wire from the LI's wiring Loom is used as a Negative Pulldown for your car's stereo. You will need to your stereo accessible to do this. If you stereo is indeed accessible then, I'll be more than happy to assist you with this. :)

Cliff - C55

Ok well in all honesty, the location of my PC is fine its just i cant hear it, if i make my wiring accessible at the time, if u can help me with the hook up to just mute the stereo when the LI alerts then i am all good. Also like before about the SIA alerts and everything i need turned off i cant connect it to my PC. But ill make sure i bring some tools with me to take apart the area to expose the wires.

th3 factory freak
11-30-2008, 05:24 PM
maybe something like
this (http://cgi.ebay.com/External-speaker-4-ohm-for-YAESU-etc-Mini-Size_W0QQitemZ220287370933QQcmdZViewItem?hash=item 220287370933&_trkparms=72%3A1205%7C39%3A1%7C66%3A4%7C65%3A12%7C 240%3A1318&_trksid=p3286.c0.m14#ebayphotohosting)

only this is, do u have to cut the end off and splice them? or what?

I've got this puppy installed now and it's LOUD enough! Thank you for posting the link.