PDA

View Full Version : ZR4 & GX65



The Breeze
11-24-2008, 10:34 PM
I installed my shifter today and according to my TV remote, it is shifting. The display on the GX65 tells me shifting front, or rear head, so that part is working. When the unit turns on and goes through the self test, the book says the RD shoulld confirm ZR4 and what mode it is set to(receive only, off, or shift). It does not say anything about laser, let alone anything about the ZR4. I cannot change the programing of the shifter either, it is set to shift (defalt). All the RD lets me do is turn the laser function on or off. I also have the ZR4 control display installed as well. It does not change these issues whether it is turned on or off. Is there something wrong, or is this normal.

focalcivic
11-24-2008, 10:40 PM
I installed my shifter today and according to my TV remote, it is shifting. The display on the GX65 tells me shifting front, or rear head, so that part is working. When the unit turns on and goes through the self test, the book says the RD shoulld confirm ZR4 and what mode it is set to(receive only, off, or shift). It does not say anything about laser, let alone anything about the ZR4. I cannot change the programing of the shifter either, it is set to shift (defalt). All the RD lets me do is turn the laser function on or off. I also have the ZR4 control display installed as well. It does not change these issues whether it is turned on or off. Is there something wrong, or is this normal.

"Shift" means laser is on and ready to jam. Make sure in the program menu to set it to shift and you are ready to go.

The Breeze
11-24-2008, 10:52 PM
"Shift" means laser is on and ready to jam. Make sure in the program menu to set it to shift and you are ready to go.

That's the problem...I can not access the program menu. The RD only lets me ( in the programming mode) turn the LASER function on or off and says nothing about the ZR4 or any of its menu options.

focalcivic
11-24-2008, 11:40 PM
That's the problem...I can not access the program menu. The RD only lets me ( in the programming mode) turn the LASER function on or off and says nothing about the ZR4 or any of its menu options.


Do you have the link cable connected to the unit? Also is the Zr4 powered up too?

The Breeze
11-24-2008, 11:50 PM
Do you have the link cable connected to the unit? Also is the Zr4 powered up too?


Yes to both...when I shoot the shifter heads with my TV remote, the RD tells me” shifting front, or shifting rear" depending on what head I am aiming at. So the thing is working, I just can't program the menu. The RD does not show ZR4 during power up either. I will call Bel tomorrow and see what they have to say. Wish me luck.

nickstath
11-25-2008, 07:36 AM
The RD does not show ZR4 during power up but blkr(bloker)on,off,or receiving.My GX65 recognize the LP905 on it's display with that message.My RX65 show LP905,on,off or receiving.

TSi+WRX
11-25-2008, 07:43 AM
Yes to both...when I shoot the shifter heads with my TV remote, the RD tells me” shifting front, or shifting rear" depending on what head I am aiming at. So the thing is working, I just can't program the menu. The RD does not show ZR4 during power up either. I will call Bel tomorrow and see what they have to say. Wish me luck.

I agree, call Bel.

I'm puzzled by this one as well, as, traditionally, both the Bel units as well as the Escort units capable of being linked will "announce" the presence of the Shifter attachment, as long as they're Linked.

Even if the detector is on "fast start up" mode.

:confused:

It appears that everything is *working* for you, though.

nickstath
11-25-2008, 07:58 AM
Yes to both...when I shoot the shifter heads with my TV remote, the RD tells me” shifting front, or shifting rear" depending on what head I am aiming at. So the thing is working, I just can't program the menu. The RD does not show ZR4 during power up either. I will call Bel tomorrow and see what they have to say. Wish me luck.

The RD does not show ZR4 during power up but blkr(bloker)on,off,or receiving.My GX65 recognize the LP905 on it's display with that message.My RX65 show LP905,on,off or receiving.

focalcivic
11-25-2008, 09:52 AM
The RD does not show ZR4 during power up but blkr(bloker)on,off,or receiving.My GX65 recognize the LP905 on it's display with that message.My RX65 show LP905,on,off or receiving.


As you know the LP905 was the Bel version of the Zr3, just the software was never updated on the Bel side.

The Breeze
11-25-2008, 12:06 PM
I just spoke with Bel. What they have done is to remove any form of lettering related to the shifters in the GX65. The GX65 says blocking instead of displaying lets say ZR4. To change the ZR4 settings with the RD, I do it in the "blocking" mode. I am a happy camper and everything is working fine and I understand the thing now. :D

Now to go out today and find a leo or two:cool:

focalcivic
11-25-2008, 12:27 PM
I just spoke with Bel. What they have done is to remove any form of lettering related to the shifters in the GX65. The GX65 says blocking instead of displaying lets say ZR4. To change the ZR4 settings with the RD, I do it in the "blocking" mode. I am a happy camper and everything is working fine and I understand the thing now. :D

Now to go out today and find a leo or two:cool:

Makes sense, post some pics of your install.

TSi+WRX
11-25-2008, 12:30 PM
Good stuff!

It's good to see that the Bel/Escort empire is doing well, by separating the capabilities/mindsets of these devices, to suit individual drivers.

The Breeze
11-25-2008, 02:02 PM
Makes sense, post some pics of your install.

http://img300.imageshack.us/img300/1665/dscn0508sr3.th.jpg (http://img300.imageshack.us/my.php?image=dscn0508sr3.jpg)


It took awhile but here it is the finished product. Note the PHOTO BLUR plate covers. All hot spots are Veiled. The color of the Jeep is white, so I really had to do some work to it. The two upper heads are held on with 3M Supermount tape. Thanks to the CFL #8 testing I mounted the rear shifter head up front as well. I hope all my effort pays off!!

TSi+WRX
11-26-2008, 09:00 AM
^ Stealth Truck! :D

crazyVOLVOrob
12-06-2008, 10:35 PM
Make sure the bubble part of the rear head is on top....otherwise you are extremely limiting the the performance of the the rear heads as Escort recessed their LEDs in their head

Lucky225
12-06-2008, 10:47 PM
Make sure the bubble part of the rear head is on top....otherwise you are extremely limiting the the performance of the the rear heads as Escort recessed their LEDs in their head

x2, the one on the driver side doesn't look like it's level either

The Breeze
12-06-2008, 10:58 PM
Make sure the bubble part of the rear head is on top....otherwise you are extremely limiting the the performance of the the rear heads as Escort recessed their LEDs in their head

Do you mean put the rear head on the top of the plate, or just make sure the bubble is up on the shifter?


x2, the one on the driver side doesn't look like it's level either


It is. Optical elusion. It's bothered me too.

Thanks for the help guy's. :)

AirMoore
12-06-2008, 11:01 PM
the one on the driver side doesn't look like it's level either


I agree... is seems like it is pointing down (and possibly off to the left). Make sure you check it with a level, its imperative for getting everything you can out of your ZR4's.


-Its not that we are ragging on your install... I think it looks great, we just are trying to help you make sure that it is going to work the most effectively it can for you.

crazyVOLVOrob
12-06-2008, 11:13 PM
Do you mean put the rear head on the top of the plate, or just make sure the bubble is up on the shifter?

I would think would be best for the bubble to be up. As long as the bubble is up it will still work at the bottom on your plate

The Breeze
12-06-2008, 11:27 PM
I would think would be best for the bubble to be up. As long as the bubble is up it will still work at the bottom on your plate

OK, thanks. It is down; I just went out to check. You guys have some GOOD eyes!! :) I check the level of the shifter heads almost daily. It looks funny to me as well, but it measures good and they are level. The bumper has an "arc" built into it, which made it hard to get the front of the heads straight.

MEM-TEK
12-07-2008, 12:14 AM
The LEDs in the ZR4's rear shifter head are mounted only a few millimeters behind the cylindrical "bubble" condensing lens on the rear head. Thus for the rear head it doesn't matter if you mount it right side up or upside down. The only thing that matters is that the rear head be mounted level.

crazyVOLVOrob
12-07-2008, 11:23 AM
The LEDs in the ZR4's rear shifter head are mounted only a few millimeters behind the cylindrical "bubble" condensing lens on the rear head. Thus for the rear head it doesn't matter if you mount it right side up or upside down. The only thing that matters is that the rear head be mounted level.
It has been tested and proven to matter by Happya$$, RacerX, and FordFocus a long time ago. Also when GOL test the zr3 everyone was very careful to masure the BUbble up as it would give the best performance

The Breeze
12-07-2008, 11:37 AM
^ Just a thought of mine. Why would it matter? The FOV is the same up or down I would think. I obviously have not tested this theory, but logically thinking, if it has a lets say, 18" or larger FOV in the up position, why would it not be an 18” or larger if the bubble was in the down position? Just thinking on this subject, I don’t understand why or how having the bubble in the up or down position would change a thing. Just tryig to understand. Has anyone tested the ZR4?

crazyVOLVOrob
12-07-2008, 02:21 PM
^ Just a thought of mine. Why would it matter? The FOV is the same up or down I would think. I obviously have not tested this theory, but logically thinking, if it has a lets say, 18" or larger FOV in the up position, why would it not be an 18” or larger if the bubble was in the down position? Just thinking on this subject, I don’t understand why or how having the bubble in the up or down position would change a thing. Just tryig to understand. Has anyone tested the ZR4?
You want the Bubbles up on both the front heads and read heads. Because Escort recesses their LEDs and having the bubble up will mean you are transmitting more IR light to jam the laser gun making the jammer more effective

Here are some internal pictures thanks to MEM-TEK
Front Head

http://www.mem-tek.com/radar/reviews/ZR4/images/ZR4_front_shifter_board_top_1000x740.jpg
Rear Head
http://www.mem-tek.com/radar/reviews/ZR4/images/ZR4_rear_shifter_board_top_1000x740.jpg

Bubbles up will be much better performance then the bubble down eventhough MEM-TEK says there is no difference I am basing my opinion off of actual test performed by members and general logic.

The Breeze
12-07-2008, 02:41 PM
^ OK...I am buying this theory on the (front) heads and escort also stamps the outside with "this side up". Then why do they not also stamp the "rear" head as well, if it is critical to the placement one way or the other? Escort also says in the installation book, to put the rear head on the top or bottom of the plate. By doing so, the bubble will be flipped top to bottom depending on the placement. But then again, they also say it will not work well on the front, and this has been proven otherwise. I am not questioning your advice, It's starting to sink in. I am just thinking out loud more or less. I will no doubt mount it on top (just to be sure), just as soon as I drill holes there. As it is now, the top of my front plate holder has no mounting holes.

crazyVOLVOrob
12-07-2008, 02:51 PM
^ OK...I am buying this theory on the (front) heads and escort also stamps the outside with "this side up". Then why do they not also stamp the "rear" head as well, if it is critical to the placement one way or the other? Escort also says in the installation book, to put the rear head on the top or bottom of the plate. By doing so, the bubble will be flipped top to bottom depending on the placement. But then again, they also say it will not work well on the front, and this has been proven otherwise. I am not questioning your advice, It's starting to sink in. I am just thinking out loud more or less. I will no doubt mount it on top (just to be sure), just as soon as I drill holes there. As it is now, the top of my front plate holder has no mounting holes.Lesson number 1, don't rely on the manufacturers as there are enthusiast that could write a substanially better manual. Escort manual and their techs say its ok to partially obstruct the heads.

Listen to me my knowledge comes from actual testing and experience behind the laser gun with experience shooting a majority of jammers. I am willing to bet that I can out shoot any Escort tech with a laser gun when going against a jammer

The Breeze
12-07-2008, 03:01 PM
DJ will be up here in a couple weeks, and a few of us are planning on getting together to test our countermeasure setups. That will be something I will try. Shoot it with the rear head mounted on the bottom and then on top, and see what difference there may be if any between the two head placements.

crazyVOLVOrob
12-07-2008, 03:26 PM
DJ will be up here in a couple weeks, and a few of us are planning on getting together to test our countermeasure setups. That will be something I will try. Shoot it with the rear head mounted on the bottom and then on top, and see what difference there may be if any between the two head placements.
It comes into effect whe the shooter is above the vehicle that they were shooting at...Mainly overpass shots but still with the bubble down you have more IR facing the ground that you do upper part of the car which is better.

TSi+WRX
12-08-2008, 08:01 AM
OK, thanks. It is down; I just went out to check. You guys have some GOOD eyes!! :)

No kidding!!!

Either that, or they have some huge monitors!!!!

I couldn't tell!!! :eek:

TSi+WRX
12-08-2008, 08:07 AM
Lesson number 1, don't rely on the manufacturers as there are enthusiast that could write a substanially better manual. Escort manual and their techs say its ok to partially obstruct the heads.

Listen to me my knowledge comes from actual testing and experience behind the laser gun with experience shooting a majority of jammers. I am willing to bet that I can out shoot any Escort tech with a laser gun when going against a jammer

+1.

To me, our hobbyist knowledge (both individual specialties as well as collective), as well as real-world experience (both in terms of testing as well as on-road experiences), greatly outweighs *any* advice from the manufacturers.

Yes, for certain things, they know best - and I am more than willing, and content, to sit on such issues until they've been proven otherwise.

But as is the case with the ZR3's rear-head "orientation" as well as the ZR3/4 "three-heads-up-front" formation/utilization, I place complete faith in what our fellow hobbyists have tested and observed, instead of blind line-recommendations from the product's makers, who may have other interests to protect, and/or may be bound by other concerns to not speak of such issues.