View Full Version : Just got my LI but 1 problem...
rockets713
01-12-2009, 02:32 PM
Wats goin on everyone. Just got my LI today and im eager to install. My only problem is i dont know how to get the wires inside the cabin. I have a 07 honda civic ex if that helps. i tried looking underneath the steering column for any hole but no luck. did the same for the passenger side. any suggestions?
speed-dreams
01-12-2009, 02:37 PM
There should be a hole with a grommet in your firewall where all the wires is ran into the cabin.
Maybe HappyA$$ can help you...
focalcivic
01-12-2009, 02:38 PM
Wats goin on everyone. Just got my LI today and im eager to install. My only problem is i dont know how to get the wires inside the cabin. I have a 07 honda civic ex if that helps. i tried looking underneath the steering column for any hole but no luck. did the same for the passenger side. any suggestions?
Google firewall holes for your car and some links come up.
chris3g
01-12-2009, 02:40 PM
if you look under the hood on the driver's side you should be able to find the main run where all the wires enter into the cabin. They should be going into a large rubber grommet and you should be able to find the other side of this grommet from the inside of the car underneath the steering column. What most people do is put a hole in the rubber, run the wires through, and then seal the hole with silicone.
Hessen
01-12-2009, 02:48 PM
Examine the firewall of your vehicle, from the engine compartment, find where the main wiring harness is, there will be a large rubber grommet there, that's your access point.
You will need a wire coat hanger, lubricant. Tape up the ends of the LI head wires, and tape that to the end of the straightened coat hanger. Pry the grommet gently with a screw driver, to make an opening so you can fed the coat hanger through there.
Ideally have someone inside car to assist pulling the wires through.
There may also be a grommet around where the steering column comes through, that can be another access point.
Good Luck.
th3 factory freak
01-12-2009, 02:51 PM
Maybe this will help:
http://img102.imageshack.us/img102/5526/oogieboogie002oh4.jpg
The new Civic motors are pretty cramped in there, put the car on a rack, it will be easier.
languy99
01-12-2009, 05:07 PM
try also the passengers side, where the cpu wires go into the cabin.
th3 factory freak
01-12-2009, 07:05 PM
OP, did you check the vehicle's owner manual? It might have some diagrams...
rockets713
01-12-2009, 09:43 PM
i will check the manuals tommorow as soon i as i wake up. i see a bunch of diffrent color wires coming from the engine into the cabin but its really tightly sealed. i check around it but nothing. maybe i should just pay a mechanic to do it.
th3 factory freak
01-12-2009, 10:11 PM
i will check the manuals tommorow as soon i as i wake up. i see a bunch of diffrent color wires coming from the engine into the cabin but its really tightly sealed. i check around it but nothing. maybe i should just pay a mechanic to do it.
It's not that bad actually, I would at least give it a shot.
You can mount the box and switch yourself, and maybe the heads too and just have someone help you with the wires.
languy99
01-12-2009, 10:16 PM
i will check the manuals tommorow as soon i as i wake up. i see a bunch of diffrent color wires coming from the engine into the cabin but its really tightly sealed. i check around it but nothing. maybe i should just pay a mechanic to do it.
the wires entering the grommets are going to be tight(they have to seal water out), what I do is use a razor and carefully slice the grommet, feed the wires though and then use slice or electrical tape to reseal the grommet.
speed-dreams
01-12-2009, 10:31 PM
Just out of curiosity,
Is it a big deal running the wires through the side of the grommet rather than through its hole?
I ran all my wires by unpluging the grommet...
languy99
01-12-2009, 10:48 PM
yeah because it can cause the wires to rub through and short, I would install some protection over the wires such as a wiring loom.
speed-dreams
01-12-2009, 11:00 PM
yeah because it can cause the wires to rub through and short, I would install some protection over the wires such as a wiring loom.
will do so, just cut a little loom in half and cover up the area that's in contact with the metal :)
rockets713
01-13-2009, 11:11 AM
the wires entering the grommets are going to be tight(they have to seal water out), what I do is use a razor and carefully slice the grommet, feed the wires though and then use slice or electrical tape to reseal the grommet.
i really dont want to slice or drill anything because my car is a lease and i dont relly feel like paying extra at the end of my term if they find out what i did. i will check my car agian for holes in a little bit.
chris3g
01-13-2009, 11:23 AM
i really dont want to slice or drill anything because my car is a lease and i dont relly feel like paying extra at the end of my term if they find out what i did. i will check my car agian for holes in a little bit.
i once returned a leased car that was lowered, and had an aftermarket wing and stereo with an amp mounted in the back and nobody said a word.
nobody is going to notice or care that you put a hole in a rubber grommet in the firewall.
speed-dreams
01-13-2009, 11:45 AM
you can undo the grommet and run the wires with a loom through the firewall...
TSi+WRX
01-13-2009, 12:42 PM
The hood-fender-A-pillar -to- door gap is also a good place to route wires in a "temporarily permanent" manner.
Just leave enough slack so that the door can close properly, and you'll be fine.
rockets713
01-13-2009, 02:18 PM
ok so heres what i did. as much as i wanted to install it myself it wasnt going to happen. i took it to mida and they did a really good job they only charged me 148$. i will post pics as soon as i can to see what u guys think. oh yea 1 more thing which ports should the 2 front head suppose to go? i put it in 2 ans 3.
th3 factory freak
01-13-2009, 05:13 PM
ok so heres what i did. as much as i wanted to install it myself it wasnt going to happen. i took it to mida and they did a really good job they only charged me 148$. i will post pics as soon as i can to see what u guys think. oh yea 1 more thing which ports should the 2 front head suppose to go? i put it in 2 ans 3.
Damn, 148...that's dirt cheap...........
The 2 heads go in 2 and 3 so you did fine.
riverwabbit703
01-13-2009, 10:35 PM
Damn, 148...that's dirt cheap...........
The 2 heads go in 2 and 3 so you did fine.
Damn.. Didn't know Midas did Laser Jammer installation.
rockets713
01-14-2009, 06:58 AM
Damn.. Didn't know Midas did Laser Jammer installation.
I didnt know either lol i live down the street from them and i explained what had to be done and they did it a good job too.
speed-dreams
01-14-2009, 07:29 AM
I didnt know either lol i live down the street from them and i explained what had to be done and they did it a good job too.
pics?
rockets713
01-14-2009, 07:31 AM
i dont have a camera on me now...maybe ill post some pics using my cell later today.
pics?
speed-dreams
01-14-2009, 08:06 AM
i dont have a camera on me now...maybe ill post some pics using my cell later today.
How they ended up running the wires to the cabin?
rockets713
01-14-2009, 10:36 AM
How they ended up running the wires to the cabin?
i have no idea...i think they did it the way everyone else was telling me to do through a hole were all the wires are. it took them a good 2.5 ot 3 hours to get the job done.
imagine me trying to get the wires through the cabin.
focalcivic
01-14-2009, 03:43 PM
Midas, huh lol. They lots of things, I guess it depends on the Midas.