PDA

View Full Version : How to Know Which Side is the Top of Z3 Heads?



95blklsc
04-09-2009, 01:40 PM
So I was doing some reading on how to align the heads on my Corvette. I just moved my Passport SRX from my car that is up for sale to the vette. I'm very familiar with leveling and aiming.....or so I thought.

Previously I had leveled based on an average of the bottom and top since they are not parallel. The manual didn't seem to clearly explain this.

I decided to try and find out what the proper way is. After some research on here I found that there is in fact a top and a bottom to the heads and the circuit board is mounted to one of them not to the black plate like I had assumed. Based on the picture I saw of one broken open it makes sense to ensure that you have them oriented correctly and aligned based on only the top surface.

After reading this and looking at the picture of one opened up I can't see any marking denoting top or bottom on my ZR3 heads. I'm sure one or both of mine are upside down but can't find any marking denoting this. Help? :eek::eek:

So how do I tell if they are upside down? Should the circuit board be on the top or bottom?

I was thinking I could try and activate them with an IR remote and see which side the IR's are closer to. But once I do this I need to know if the LED's should be closer to the top or bottom. Any input appreciated, thanks!


Thanks!

partsfreak
04-09-2009, 01:46 PM
I had same question and was told bubbles on top.:)
Thanks to those who gave me the quick responses too.:thumb2:

95blklsc
04-09-2009, 01:49 PM
Thanks, I'll take a look before I get in the car to go home from work and see how I have them mounted.

I'm surprised the manual doesn't state this. I think it must be pretty important.

95blklsc
04-09-2009, 04:35 PM
Well one was upside down it looks like. Is the conformation from escort somewhere that bubble up is in fact the correct mounting?

Also, FYI for anyone with a C6 Corvette. If you have the rear license plate jammer mounted, it will prevent you from opening the rear hatch with a key if you FOB dies. This could be a problem as this is the ONLY way to open the car if you have a dead battery in the car or remote. If you ware at home no biggie, get a screw driver and take the jammer off but it might be more of a pain if you are away from home. :eek:

erickonphoenix
04-09-2009, 05:43 PM
I went by the "rcvr" decal on the back. going by that reference it's bubbles up.

95blklsc
04-09-2009, 05:46 PM
I'm going to go turn it around shortly, but I don't think mine have a decal.

MEM-TEK
04-09-2009, 07:14 PM
If you hold the head so that the front of it is facing the sun, you should just be able to see the edge of the circuit board and the emitter LEDs. :)

Stealth Stalker
04-09-2009, 07:30 PM
Whoa, wait a sec. Are you talking about Z3 heads, or ZR3 heads? I think I may have misunderstood this post and moved it inappropriately. I'm not familiar with a Z3.

MEM-TEK
04-09-2009, 07:51 PM
I missed that too. What is a Z3?

partsfreak
04-09-2009, 07:52 PM
I think he meant zr3
I could be wrong. just ask my wife.;)

95blklsc
04-09-2009, 09:10 PM
yea I'm stupid, sorry for the mistake. It's been a long week!

MEM-TEK
04-09-2009, 09:15 PM
^^ No problem. You might even be able to see the edge of the circuit board by shining a bright flashlight through the top of the ZR3 heads. :)

95blklsc
04-09-2009, 09:33 PM
The circuit board should be on the top of the housing or the bottom?

MEM-TEK
04-09-2009, 11:02 PM
I can't remember re the ZR3, but with the ZR4 the boards are near the bottom of the housings.

grasshopper
05-14-2009, 08:34 PM
i notice the bubble but just made sure they were level ill have to check on them