PDA

View Full Version : dual ZR3 install.



partsfreak
04-11-2009, 01:31 PM
I know that the ZR3 is not a powerhouse in the jammer world and just bought one for my 98 GMC pickup. I actually dont feel confident that it is going to do much for the truck. I have been thniking that maybee if I just bought another one and installed both it would increase coverage and performance. The total cost would then be $500. so thats not too bad if this would work.
So my question is: Since they would both be ZR3 would they work together or interfere with each other?
Are there any problems you know about that I havent thought of?
Does this sound like a good idea or just forget about it and use what I have?

oahuyahoo
04-11-2009, 02:15 PM
I'd get a dual LI and put it on hte front and put the ZR3's on the back. One save and it has already paid for itself. Just be sure to not use the same ground nor mount the cpu's in hte same vicinity.

fire65
04-11-2009, 02:29 PM
Just curious why you bought if you were pretty sure it would not protect the truck and now double the money to install another set. Quad Blinder or dual LI would have been cheaper in the long run.

partsfreak
04-11-2009, 03:51 PM
I did it because it was a cheap impulse buy. I know when I put veil on it it will help. Lidar isnt a big threat in my immediate area yet but I want civerage when I make trips where it is.
Im not interested in spending the money fo an LI yet.
Thanks for the input.

crazyVOLVOrob
04-11-2009, 04:22 PM
Why not put a ZR3 on both cars you have

3 heads up front and VEIL on your truck is a must though

speed-dreams
04-11-2009, 04:26 PM
Why not put a ZR3 on both cars you have

3 heads up front and VEIL on your truck is a must though
X2

partsfreak
04-11-2009, 04:39 PM
Why not put a ZR3 on both cars you have

3 heads up front and VEIL on your truck is a must though

I had planned on putting the rear head up front but was told it would cause interference. Its also on Roys video so I decided not to do that.
I figure that for another $250 which is what I was quoted for a "Professional install"
I could just get another set and do it myself. Same Money invested but double coverage. 4 heads up front & 2 in back. + Veil. I would be pretty confident with that setup for cheaper than most other setups. I havent heard of anyone else running this setup here. Nobody seems to know if the 2 would work in tandem or compete tho.:dontknow:

When LIDAR becomes a real threat here Im going LI on the Acura.
The sleeper only gets the best.:cool:

ELVATO
04-11-2009, 05:17 PM
Roy was talking about the ZR4 in his video. The ZR4 didn't cause interference when we tested it, though. In fact, it helped against roof line shots (we installed in a triangle fashion.)

As for the ZR3, many people installed all 3 up front. It's known as the "enthusiast" (aka in a triangle fashion, be it a right side up, or upside down install) install. Don't know who told you 3 head ZR3 caused interference...

crazyVOLVOrob
04-11-2009, 05:25 PM
Roy was talking about the ZR4 in his video. The ZR4 didn't cause interference when we tested it, though. In fact, it helped against roof line shots (we installed in a triangle fashion.)

As for the ZR3, many people installed all 3 up front. It's known as the "enthusiast" (aka in a triangle fashion, be it a right side up, or upside down install) install. Don't know who told you 3 head ZR3 caused interference...
Too many people think Roy's word is from God and don't realize that some members have been doing the 3 heads zr3 up front for years

And thanks for your ZR4 3 head up front test you and the CFL crew did.

partsfreak
04-11-2009, 06:51 PM
Roy was talking about the ZR4 in his video. The ZR4 didn't cause interference when we tested it, though. In fact, it helped against roof line shots (we installed in a triangle fashion.)

As for the ZR3, many people installed all 3 up front. It's known as the "enthusiast" (aka in a triangle fashion, be it a right side up, or upside down install) install. Don't know who told you 3 head ZR3 caused interference...

Thanks, This is just the kind of info I have been looking for. :)
I dont have to use a front plate but I do have a big plastic plate holder on the chrome bumper. I now plan on flush mounting the rear head in it to help. I think this should do the trick. If Roy got JTG on the white Sequia I should be O.K. with 3 heads and veil.

What would the benefits be to install the rear head upside down?

crazyVOLVOrob
04-11-2009, 06:55 PM
Thanks, This is just the kind of info I have been looking for. :)
I dont have to use a front plate but I do have a big plastic plate holder on the chrome bumper. I now plan on flush mounting the rear head in it to help. I think this should do the trick. If Roy got JTG on the white Sequia I should be O.K. with 3 heads and veil.

What would the benefits be to install the rear head upside down?
Don't believe Roy's testing, he holds a bias:cool:

ELVATO
04-12-2009, 03:59 AM
I didn't mean the rear head being upside down. I meant the installation being an upside down triangle.

For example:
http://i96.photobucket.com/albums/l183/Jjokin3much/07_F150_front.jpg

Red & Green = upside down. Good if you have a plate.
Red & Yellow = right side up. Probably not as good on a truck, but would help with roof line shots, and hood shots. Would work better on a car, where it could cover some of the plate, and some of the hood.

Just want to clarify, though, that just because we didn't get interference during testing (or at least loss of performance) doesn't mean interference will never happen. I know I've read about other threads about having possible issues with interference. I did see a possible solution of painting the sides of the heads (obviously not the front) with black tape, but it hasn't been tested.

partsfreak
04-12-2009, 06:59 AM
I didn't mean the rear head being upside down. I meant the installation being an upside down triangle.

For example:
http://i96.photobucket.com/albums/l183/Jjokin3much/07_F150_front.jpg

Red & Green = upside down. Good if you have a plate.
Red & Yellow = right side up. Probably not as good on a truck, but would help with roof line shots, and hood shots. Would work better on a car, where it could cover some of the plate, and some of the hood.

Just want to clarify, though, that just because we didn't get interference during testing (or at least loss of performance) doesn't mean interference will never happen. I know I've read about other threads about having possible issues with interference. I did see a possible solution of painting the sides of the heads (obviously not the front) with black tape, but it hasn't been tested.


Thanks for the clarification. In my GMC the grill is similar in shape but smaller and more centered than the Ford grill in the picture. This will make it easy for me to place the top heads farther up next to the headlights. The lower head would end up pretty much where you have it in the bumper in the picture. The spread between heads will be farther apart with the top heads closer to the hood so that may help with the higher up shots.
Thanks again, your input is greatly appreciated:)
I will try to get some pics up soon

partsfreak
04-12-2009, 01:53 PM
jpg

Here is a picture of the truck. You can see how I can place the 2 heads up next to the headlights and the rear head I want to put on the plate holder( recess it itn the bottom)

ELVATO
04-12-2009, 02:29 PM
You wanna put all 6 heads up front, or just one ZR3 for now? If only one, then yea, rear head in plate holder, and 2 heads in grille by headlights, though that front bumper worries me a little.

If you were to have another ZR3 system, I might consider putting the other 2 front heads above the fogs (to cover those and the bumper) and the other rear head above the GMC.

partsfreak
04-12-2009, 02:38 PM
You wanna put all 6 heads up front, or just one ZR3 for now? If only one, then yea, rear head in plate holder, and 2 heads in grille by headlights, though that front bumper worries me a little.

If you were to have another ZR3 system, I might consider putting the other 2 front heads above the fogs (to cover those and the bumper) and the other rear head above the GMC.

Just 1 ZR3. I decided not to get another one since I am going to put all 3 heads up front. I plan on putting veil on the headlights, foglights and at least trying it on the bumper. That bumper worries me alot:o
Thx

speed-dreams
04-12-2009, 02:40 PM
You wanna put all 6 heads up front, or just one ZR3 for now? If only one, then yea, rear head in plate holder, and 2 heads in grille by headlights, though that front bumper worries me a little.

If you were to have another ZR3 system, I might consider putting the other 2 front heads above the fogs (to cover those and the bumper) and the other rear head above the GMC.

Just 1 ZR3. I decided not to get another one since I am going to put all 3 heads up front. I plan on putting veil on the headlights, foglights and at least trying it on the bumper. That bumper worries me alot:o
Thx
You'd need a lot of veil for the front end :(

ELVATO
04-12-2009, 02:45 PM
It would probably be a lot easier if you had a "car" bra, or at least something to cover that bumper.

partsfreak
04-12-2009, 02:47 PM
So maybe it would be a good idea to get another zr3 then and put 4 heads up front. 2 in grill 2 by the fogs?

ELVATO
04-12-2009, 02:55 PM
Not sure. Don't know how much you could get another ZR3 for. Wait for others' opinion.

partsfreak
04-12-2009, 03:00 PM
They are still on sale for $ 250. No problems there.
I was going to wait for the new Blinder to come out before but the wind shifted from the rose garden to the sewer lately on that subject if you know what I mean.;)

speed-dreams
04-12-2009, 03:10 PM
IMO, the current Blinder j16 TS enabled is good enough. I tested an F150 with M25+Veil+bra, and it was JTG to the UL and TS...

category4
04-12-2009, 08:47 PM
If I already had the ZR3's I would install all 3 up front and Veil the headlights then test. You may find it will do quite well.

partsfreak
04-13-2009, 11:35 AM
I went ahead and ordered another set soIi can put 2 heads up by the headlights 2 down by the foglights/bumper and 1 on the plate holder. Then the last one will go on the rear plate.
Maybe overkill but better safe than sorry.

xlx
04-13-2009, 07:42 PM
Maybe overkill but better safe than sorry.



Your new avatar pic somehow seem appropriate now with that statement :D :beer:

I'm just trying out one set... initially the idea was if I get caught and they get confiscated a bit over 200 is tolerable.. but not so sure now with that strategy either. Well if need be a pair of LI or Blinder in the future... For now I bought a cheap black plastic license plate frame with the most profile to fiddle with and trying to fit the rear head inside to make it less obtuse. Doesn't look promising though. How to veil the front plate without looking obvious will be another huddle.

Stealth Stalker
04-13-2009, 08:40 PM
Your new avatar pic somehow seem appropriate now with that statement.
I can't tell what his avatar pic (or his signature pic either) are.

Anyhow, I wouldn't get too convinced about the overkill until you test it. And it certainly isn't overkill on your rear, which is typically harder to protect than the front end. You'll feel awful silly if you overkill your front end, sacrificing your rear end to instant pwn4g3.

partsfreak
04-13-2009, 08:45 PM
Your new avatar pic somehow seem appropriate now with that statement.
I can't tell what his avatar pic (or his signature pic either) are.

Anyhow, I wouldn't get too convinced about the overkill until you test it. And it certainly isn't overkill on your rear, which is typically harder to protect than the front end. You'll feel awful silly if you overkill your front end, sacrificing your rear end to instant pwn4g3.

You are right about the rear. Besides the fact theres a big chrome bumper theres just nowhere to mount any extra heads. :(

Stealth Stalker
04-13-2009, 09:04 PM
That big bumper is both a curse and a blessing. It makes a great platform for mounting jammer heads at the far outer corners of your vehicle, which people in most cars cannot do.

partsfreak
04-16-2009, 04:15 PM
I recieved my 2nd ZR3 toaday and when I went to get my tools together I figured out my Dremel is broken and my straight edge has disapeared.:mad:
Now I have to go buy frikin tools too. SOB!