View Full Version : Got my li :-o
DarkChewby
05-14-2009, 07:39 PM
I bought my LI from Cliff earlier this week, and it got in today. :) I'm excited and nervous about the installation, since I have a new car. I am planning on taking it to crutchfields for installation, since my friend took his Civic Si to get his stereo upgraded and wolfers upgraded, and he was happy about it that he went back 3 times. ResellerRatings also gave them 9+/10. Hopefully they will do the same job.
I was looking at the stuff that's included. Is the mounting bracket that giant piece of metal? So... I am guessing you are suppose to bend it to mount the emitters? I am kind of afraid of since the place that I want to screw it in seems like it may be crucial to AC. So, since looking at the large mounting bottom, I am leaning toward just glueing the emitters down to the car. Seems like the large surface area would make it hold very well. Is there any type of very strong, but not damaging and removable adhesive to use? I am planning on using 3M molding tape, hopefully that stuff is weather resistant.
Also, can someone link me or tell me how you make another switch to switch between Parking/Jamming mode or Parking/Detecting/Jamming mode?
So, today I was driving down 81, with the STi. I detected some state troopers, but some where just chilling in the straightaway with no alert coming through. Were they lasering me or what? I thought you have to get out of the car and point it at us like a gun. They were sitting in the car, but not sure what they were doing.
Thanks!
Stealth Stalker
05-14-2009, 08:23 PM
Wait, I'm confused.
If you're taking it to Crutchfield for installation, then why all the questions about glue and mounting brackets?
DarkChewby
05-14-2009, 08:28 PM
Wait, I'm confused.
If you're taking it to Crutchfield for installation, then why all the questions about glue and mounting brackets?
I can trust him with wiring the LI, but I don't know they know how to mount it!. Since it is LJs are illegal in my state. So I want to give him specific instructions on mounting the emitters! The manual doesn't seem very helpful on what pieces are what.
robcollins5
05-14-2009, 08:32 PM
But mounting is the hardest part. All you have to do after that is find a hole in the firewall for the Head cords and give the control box power just like hardwiring an RD. Surely you can do that!
rc
DarkChewby
05-14-2009, 08:38 PM
But mounting is the hardest part. All you have to do after that is find a hole in the firewall for the Head cords and give the control box power just like hardwiring an RD. Surely you can do that!
rc
NOPE :) Lol I don't know much about cars! And yes I realize mounting is the hardest part that's why I want to give him very specific instructions, so the LI's performance isn't degraded by the mounting.
ELVATO
05-15-2009, 09:10 AM
Tell him you're mounting parking sensors, and they need to be straight and level for best performance ;)
focalcivic
05-15-2009, 09:42 AM
Post a few pics of your car for suggestions. As for molding tape it is weather resistant if mounted right.
Montu
05-15-2009, 10:21 AM
I used the Extra Strength molding tape and I've been though lots of rain and car washes just fine
DarkChewby
05-15-2009, 11:00 PM
Post a few pics of your car for suggestions. As for molding tape it is weather resistant if mounted right.
http://img7.pictiger.com/ca6/18098184_th.jpg (http://img73324.pictiger.com/images/18098184/)
You can click on it to get a bigger image.
This is where I plan on mounting the LI heads. This place seems to be the furthest apart I can mount them. I think I am going to mount the heads so it is flush with the car's sticking outness... if that makes sense.
DrCoke
05-15-2009, 11:27 PM
I got a bad feeling about the install.
snoopyc4
05-15-2009, 11:29 PM
I got a bad feeling about the install.
only way to test it is to break the speed limit and see if u get pulled over or not :D
Stealth Stalker
05-15-2009, 11:32 PM
I got a bad feeling about the install.
Yeah, looks like it's going to be a major pain in the arse.
MEM-TEK
05-15-2009, 11:36 PM
only way to test it is to break the speed limit and see if u get pulled over or not :D
Well, that is one way to find out how good the install is. :)
DarkChewby
05-15-2009, 11:45 PM
I got a bad feeling about the install.
Yeah, looks like it's going to be a major pain in the arse.
Why do you think it's going to be a pain? It seems pretty easy since the area I am getting it installed is pretty much flat inside.
Stealth Stalker
05-15-2009, 11:52 PM
Maybe it's just the angle of that photo, but it looks like a lot of tedious levelling work, and custom bracket fabrication.
EDIT: On second look, it looks like there may be a flat ledge in there that I didn't notice before. If so, it could go very easy. Just not a particularly good photo to tell from.
DarkChewby
05-16-2009, 12:32 AM
Maybe it's just the angle of that photo, but it looks like a lot of tedious levelling work, and custom bracket fabrication.
EDIT: On second look, it looks like there may be a flat ledge in there that I didn't notice before. If so, it could go very easy. Just not a particularly good photo to tell from.
Yea it has a flat edge about 4 inches wide. that extends all the way across the front. There are partitions on the very edges that won't let me mount there. But not including the two side holes, there is a partitions wide enough to accommodate the brackets. Cliff sent me the front brackets and the rear brackets. the rear brackets seem to have a ton more surface area, so I am thinking of using that. I don't know how strong Molding tape is. But if it's really strong, I guess I could just use the original front brackets. I am going to take a pic of my car's front tomorrow and just hold a LI emitter to where I think it should go.
What do you think of the locations of the jammers? Do you think that will be optimal to detect and jam?
Stealth Stalker
05-16-2009, 12:55 AM
What do you think of the locations of the jammers? Do you think that will be optimal to detect and jam?
Yeah, that seems ideal, so long as you do not make the mistake of recessing them too far. Keep them out at least even with the front edge of the hood, if not farther out.
DarkChewby
05-16-2009, 01:47 AM
What do you think of the locations of the jammers? Do you think that will be optimal to detect and jam?
Yeah, that seems ideal, so long as you do not make the mistake of recessing them too far. Keep them out at least even with the front edge of the hood, if not farther out.
Yea, I am trying to get it as far out as possible without sticking out of the hood or make it look obvious. I think thinking taking a ruler and just put it vertically against the area of installation. The front of the emitter needs to touch the ruler. Going to take pictures soon and post it.
What i've wonder is, why does the LI come with regular sized jammer heads, when there are slim jammer heads? They seem to be the exact same price. Is there a performance difference?
Stealth Stalker
05-16-2009, 04:25 AM
The difference in the size of the heads has to do with the difference in the type of optics inside. The regular heads have deeper set diodes to create a tighter "beam" pattern for greater distance. The slim heads are made to project a wider beam for the typical characteristics of a rear end. That does not require as deep a head.
takeshi
05-16-2009, 11:51 AM
I am planning on using 3M molding tape, hopefully that stuff is weather resistant.
There's a good chance that it is already used to hold badges or other stuff on your car.
MEM-TEK
05-16-2009, 12:32 PM
3M VHB tape is much better.
speed-dreams
05-17-2009, 08:13 AM
3M VHB tape is much better.
I agree, I wish they come in gray or black color :rolleyes:
DarkChewby
05-19-2009, 10:39 PM
3M VHB tape is much better.
I agree, I wish they come in gray or black color :rolleyes:
Isn't Molding Tape more removable than VHB Tape? I don't want something that's ridiculously hard to get off if I decide to take it off.
MEM-TEK
05-19-2009, 11:33 PM
3M VHB tape is much better.
I agree, I wish they come in gray or black color :rolleyes:
I use a black Sharpie to make the edges of VHB tape black.
Isn't Molding Tape more removable than VHB Tape? I don't want something that's ridiculously hard to get off if I decide to take it off.
Wet/soak VHB with isopropyl alcohol as you take it off. It is not that much more difficult to remove compared to molding tape.
DarkChewby
05-20-2009, 11:45 AM
Alright, I am going to recommend vhb tape to him when I meet with him this coming Monday