PDA

View Full Version : How much Installing LI, cost you?



DarkChewby
05-25-2009, 12:42 PM
Hello,

So I finally found a place that will install the LI for me. They seem to be very into doing quality work, and they have done work on BMW, Lexus, all the way up to Rolls Royce costing a quarter million. However they have never dealt with the LI, and I told them it was a parking sensor. They have however done many parking sensors. They are charging $60/hour and the quoted time they said would cost me around 4-8 hrs being $240-480 to install the LI and the direct wire cord for stealth install for my RD detector. They would have to take off the front bumper and mount it and wire it. I was suprised by the cost. Seems very expensive, but they seem to be quite confident that they can get it installed properly.

What do you all think? If you got yours professionally done, how much did it cost you?

SpeedinLancer
05-25-2009, 01:31 PM
That actually sounds about right. High-end custom shops usually charge around the $60/hr mark and sometimes more. It takes them awhile to do things because they take their time with everything and don't rush, which is good and bad for you. It all depends on how important a quality install is to you. I have paid before to get things installed because how I wanted it was beyond my expertise.

However, I will tell you this. I am going to be installing my Li without taking it to a custom shop, jammers aren't terribly difficult to install. On that same note however, I would recommend having someone with you to guide you through the install as I am going to have.

The shop will do quality work and you will be happy with the install, it is just a matter if you want to pay for it or not.

th3 factory freak
05-25-2009, 02:07 PM
I paid $450 and my friend who is a master mechanic helped me.

It involved removing the bumper, mounting, routing the wires.

jerry540i
05-25-2009, 02:11 PM
Um, I drive a Lexus. I paid 1 hour ($65) for a fantastic install at a car stereo/electronics place.

Anyone that needs 4-8 hours to install the LI doesn't have a clue what they're doing.

J/

snoopyc4
05-25-2009, 02:41 PM
I had my 9500ci installed at car toys and it cost me $300 for the install

DarkChewby
05-25-2009, 03:47 PM
Um, I drive a Lexus. I paid 1 hour ($65) for a fantastic install at a car stereo/electronics place.

Anyone that needs 4-8 hours to install the LI doesn't have a clue what they're doing.

J/

Wow 1 hour? That is really speedy.

DrCoke
05-25-2009, 04:13 PM
I installed my 9500CI with the zr-4 shifter in my 2000 Honda and it took no more than 2 hours. Heck, it took me longer to install the alarm in my car. Running wires is easy, to install the shifter heads perfectly and level took the longest. 9500CI has the following to istall: radar head in front bumper, 2 shifter front bumper, rear head, GPS antenna, remote display, and remote control. It has more parts than LI. ANyone who seen my install will be pleased. I think I can personally install an LI for my car in 30-60 minutes. Why don't you post your location and see if anyone on the forumn lives near you to install and test. Forumn members here were happy to test my setup and i feel they will go the same for you.

Av8terZ06
05-25-2009, 04:43 PM
I did my own install of my quad LI. It took me a few hours because I fabricated my own brackets and also because Im a little anal when it comes to things being perfect. I wanted to make sure of my locations for the heads for best performance and being level, so I thought about it carefully before diving into it. It really isnt that hard to install these things. Just takes a little time and an imagination. If people are paying that much for installs, I think I may open up a little side business. LOL

djrams80
05-25-2009, 04:58 PM
I'll emphasize this one more time. Straight, unobstructed, properly spaced and level are the keys to having a laser jammer perform properly.

jerry540i
05-25-2009, 05:27 PM
Um, I drive a Lexus. I paid 1 hour ($65) for a fantastic install at a car stereo/electronics place.

Anyone that needs 4-8 hours to install the LI doesn't have a clue what they're doing.

J/

Wow 1 hour? That is really speedy.

I told the guy where and how I wanted the heads mounted. He mounted them nice and level, hid the wire behind the engine shround, popped a grommet off and fed the wires though the firewall. Next, the guy even custom cut out a circle for the on/off switch, and presto--1 perfectly installed LI in little over an hour (charged me for 1 hour).

J/

th3 factory freak
05-25-2009, 07:51 PM
Um, I drive a Lexus. I paid 1 hour ($65) for a fantastic install at a car stereo/electronics place.

Anyone that needs 4-8 hours to install the LI doesn't have a clue what they're doing.

J/

Wouldn't be so quick to judge, all cars are different, some require more careful attention due to different factors.

Also, how many people worked on your install at once?

DarkChewby
05-25-2009, 08:29 PM
The funny thing is on the way back from the store and on the way there. This was one of the first few times I've seen someone used LIDAR. There was a cop on a bike hitting everyone on the highway I was going 68 in a 55 mph. I thought I was dead, but I think the cars to my right were blocking him from clocking me. On the way back I saw the cop had pulled over somebody, and there was another cop set up a couple miles away.

The most cops I've seen on the highway in a while, the police really went to town with ticketing people today on memorial day.

crazyVOLVOrob
05-25-2009, 09:43 PM
I paid $350 for my quad installation

snoopyc4
05-25-2009, 11:38 PM
wow thats cheap. where did u get it installed?

crazyVOLVOrob
05-25-2009, 11:44 PM
wow thats cheap. where did u get it installed?
An install shop I use to build boxes for. They did alot of my car audio work in the past as well as tinting for both my cars.

Its not a franchise and all I do is ask the owner after I get the initial estimate...What if I pay in cash? Usually don't have to pay sales tax which is a blessing

speed-dreams
05-25-2009, 11:59 PM
install everything yourself and save $$$$

DarkChewby
05-26-2009, 10:08 PM
Haha.... Yea right. If I try to install it myself. my car will have its engine fall out while I am driving.

I think I am just going to make the most of it, and just purchase direct wire cords for the Cheetah and my Garmin Nuvi and have him wire the Beltronic speakers. shouldn't take very much extra time since he has to wire into the cabin anywyas.

djrams80
05-26-2009, 11:48 PM
Where do you live? You might be able to find a forum member near you that would be willing to help you install it for a pizza and a twelver, or something similar.

REBinc
05-26-2009, 11:55 PM
Working on your own car is awesome :D. It's the only way you can make sure it's done right.

trailtow
05-27-2009, 12:28 AM
Working on your own car is awesome :D. It's the only way you can make sure it's done right.
X2

deckman
05-28-2009, 12:57 PM
Did it myself. I had to take the bumper off my 911, go through two walls and remove the front trunk liner for wire concealment. It took a while.

PMoth
05-28-2009, 07:23 PM
The install facility that I consult and test for charges $200-1500+ depending on the number of heads and vehicles. This may include custom molded parts, ordering/cutting/fabricating factory panels for direct replacement, direct front and rear as well as off-axis testing with multiple guns. Vehicles completed have ranged from Volvo S40 to Audi R8. Typically, newer and more prestigious vehicles have higher installation costs for obvious reasons.

Also, if an installer completes a dual head install of any jammer in anything other than a go-kart in an hour, he should probably be shot.

partsfreak
05-28-2009, 07:44 PM
Working on your own car is awesome :D. It's the only way you can make sure it's done right.

x3

PMoth
05-28-2009, 07:52 PM
Working on your own car is awesome :D. It's the only way you can make sure it's done right.

Also a very quick way for a novice installer to burn his car to the ground.:p

Stealth Stalker
05-28-2009, 08:05 PM
LOL! Where's RadarKid's burning Mustang pic when we need it?

DarkChewby
05-29-2009, 09:23 AM
LOL! Where's RadarKid's burning Mustang pic when we need it?

What happened to his mustang?

speed-dreams
05-29-2009, 09:39 AM
With the money you guys pay for installs, you can get a LI quad instead of a dual ;)

ELVATO
05-29-2009, 09:55 AM
Hah, never thought of it that way :)

Stealth Stalker
05-29-2009, 02:11 PM
LOL! Where's RadarKid's burning Mustang pic when we need it?
What happened to his mustang?
He doesn't have a Mustang. He just chopped a photo of djrams80's Mustang to look like it was on fire.

ELVATO
05-29-2009, 02:36 PM
That was RadarKid's doing? For some reason, I thought it was JDS who had done that. Either way, funny :lol:

djrams80
06-01-2009, 07:10 AM
http://img177.imageshack.us/img177/1/mustang1dsc00884ji11lo0.jpg (http://img177.imageshack.us/my.php?image=mustang1dsc00884ji11lo0.jpg)

Stealth Stalker
06-01-2009, 08:12 AM
LOL! Do you have the larger one?

A friend of mine (Jack Ingram) wrote and recorded a song called Mustang Burn that was pretty popular in Texas for awhile. I think he had a CMT video for it too. Everytime I hear it, I think of that picture.

sonny03106
06-01-2009, 11:17 AM
I live in NH. I took my BMW 3 series to Auto Sounds in Exeter NH for install. It cost $320 for LI quad and also fishing the wire in front for my V1.

PMoth
06-02-2009, 10:07 AM
I'd love to see the wiring throughout the engine bay and under dash connections for many of these cheaper installs. I'd also love to see how the vehicle performs @ engagements of 300 ft and further. A "real world" quick test.

sonny03106
06-05-2009, 10:39 PM
I'd love to see the wiring throughout the engine bay and under dash connections for many of these cheaper installs. I'd also love to see how the vehicle performs @ engagements of 300 ft and further. A "real world" quick test.

are you talking about my install? I could get some pics for you. As far as the testing goes I havent had a chance to test the setup yet. I just posted a new thread asking for help on the testing my setup..

PMoth
06-06-2009, 07:46 AM
I'd love to see the wiring throughout the engine bay and under dash connections for many of these cheaper installs. I'd also love to see how the vehicle performs @ engagements of 300 ft and further. A "real world" quick test.

are you talking about my install? I could get some pics for you. As far as the testing goes I havent had a chance to test the setup yet. I just posted a new thread asking for help on the testing my setup..

No sir, not @ all. It was a general question and aimed @ no one in particular.

thx1138
06-07-2009, 04:19 PM
Just had a LI dual installed:D. Cost $150 ( 3 hours). Installer did OK with the wire routing and firewall penetration, but despite my previous instructions, recessed the heads way deep. I redid this part of the install myself to pull the heads forward/flush. I'm may move them back slighly or move them higher in the grill later. Here is my advice if you have an installer who isn't familiar with the product.

1. Mount the heads yourself. Fabricate your own brackets if needed and put the product where it will work best.

2. Stay with the install shop when they work on your car. (I couldn't stay with the car since I did it while I was at work). make sure things are going per your instruction.

3. Get an external speaker. The speaker in the main box is ok, but with any noise on the car I can't understand what its saying.

I'm waiting to test everything. Saw two FHPs using laser this weekend, but they didn't target me:mad:

iceberq
06-07-2009, 05:23 PM
$280 at Luxury Details, Framingham Mass 01702 (http://www.luxurydetails.net). Installed CPU box near glove box space, kill switch in sunglass holder area.

deckman
06-08-2009, 01:14 PM
I'd love to see the wiring throughout the engine bay and under dash connections for many of these cheaper installs. I'd also love to see how the vehicle performs @ engagements of 300 ft and further. A "real world" quick test.

So would I for mine! But I can't find anyone around here that can help with that. :(