PDA

View Full Version : Problem - rd going off almost non-stop



lowcel
08-14-2009, 07:52 AM
I recently purchased a Cobra XRS 9345 for my sport bike. I use it in my Tacoma also and it works fine. However, when I put it on my motorcycle the laser goes off almost non-stop. I have it hard wired straight from the battery (fused).

Anyone have any suggestions on what is causing the problem?

Here are two pictures, you will need to remove the space in the http to see them though. I don't have 15 posts so I can't insert the pictures. :o

ht tp://i18.photobucket.com/albums/b148/LowCel/motorcycles/rd1.jpg
ht tp://i18.photobucket.com/albums/b148/LowCel/motorcycles/rd2.jpg

FoolishOne
08-14-2009, 10:17 AM
Cobra's are manufactured to an incredibly low quality and are junk. When subjected to the vibrations of a motorcycle, I would think it would turn right into dust. So, the vibrations may have probably effected the hardware, like a solder joint or something, and hence the falsing.

Could also be electrical inference, that it doesn't experience on the windshield of your truck.

Hard to tell from the pictures, but do you have it mounted along that windscreen?

Like this...?

lowcel
08-14-2009, 10:37 AM
Thanks, after messing around with it some while installing hid's I found out that it was the ground location. Now that I moved the ground I can't get the laser to go off by revving the engine anymore.

Unfortunately I can't view your picture, this site won't allow new members to view pictures. :(

FoolishOne
08-14-2009, 10:42 AM
h ttp://i240.photobucket.com/albums/ff12/ICantComeUpWithSomething/mc.jpg

lowcel
08-14-2009, 10:49 AM
It is mounted just to the side of the windscreen, behind the plastic (hidden).

snoopyc4
08-14-2009, 10:53 AM
Here is what I recommend:

YouTube - radar detector test Whistler or Cobra (can't remeber)

FoolishOne
08-14-2009, 10:53 AM
Is it level? Parallel to the ground?

lowcel
08-14-2009, 11:01 AM
Is it level? Parallel to the ground?

No, it is about a 30 degree angle. Display is on the high end.

FoolishOne
08-14-2009, 11:08 AM
Although you will not be able to read it, for better detection, I suggest bending the bracket as shown on page 2 on the manual. It's up to you though.

h ttp://cobra.com/downloads/XRS9345_MANL.pdf

v1user
08-14-2009, 03:01 PM
Out of respect for you bike give it something better than crapola.

rideco
08-17-2009, 10:56 AM
Out of respect for you bike give it something better than crapola.

For real you have an MV Agusta and you put a cobra on it. Junk the Cobra and buy a better RD.. Your licence will thank you.

Also you need to mount the detector correctly for it to work well. The current solution and is not going to help you much if at all. I know it can be an eye sore but mount the detector level and with a view of the road. Or just go with a escort 9500ci for the bike and have the sweetest RD+bike setup most people have ever seen. my 2 cents...
rideco

v1user
08-17-2009, 06:41 PM
Out of respect for you bike give it something better than crapola.

For real you have an MV Agusta and you put a cobra on it.

HOLY %#$%!!! I missed that. An MV Agusta with cobra? You have to be kidding me.

Freebird
08-17-2009, 06:45 PM
I had the same problem with a Escort x-50 on my sport bike. You wouldnt happen to be running a zero gravity tinted windscreen would you.

My unit was mounted with a stem mount and would constant false laser due to the tinted windscreen.