PDA

View Full Version : Advice on placement, Veil with a ZR3 on a C6 Vette



velcro
09-22-2009, 04:15 PM
I drive a Yellow C6 Corvette, with an Escort 9500ix. I also live in an area where Laser Jammers are illegal, but a petty, secondary offense.

Because prices are very low, and it will integrate nicely with the 9500ix, I've picked up an escort ZR3.

As jammers are a secondary offense where I live, you can't be pulled over just on suspicion of one. I also plan on shutting it down with the mute button after I quickly get down to speed (not going to JTG) to give a reading. It does worry me that the rear jammer will stick out like crazy on a body colored license plate of my Velocity Yellow vette.

So, I'm looking for some advice. Should I install the rear jammer, or will it be more stealthy not to (and not give an officer who pulls me over immediate suspicion).

Are 2 ZR3 jammers on the front alone sufficient for a C6 corvette? Should I install the rear Jammer up front (if so any tips on where)?

Would I be better off to just run the 2 jammers upfront and Veil the headlights (than running 3 up front), or should I run all 3 up front AND Veil. I'm not really sure I like the appearance of Veil on the Yellow C6. What's going to give solid (adequate) protection, and raise the least suspicion? What real risk do I run not running anything aft, and is the ZR3 pretty poor on that anyways on a C6 (possibly with a Veiled rear plate).

I should also add that I'm not running a front plate either (required in my state but I choose not to).

Thanks in advance for any advice y'all have.

stlcardsfan
09-22-2009, 04:33 PM
Put all 3 heads up front. ZR3s can be effective on Veiled out black Vettes but yellow isn't the best color for laser stealth so I honestly can't say how they would do.

Stealth Stalker
09-22-2009, 09:33 PM
Are 2 ZR3 jammers on the front alone sufficient for a C6 corvette? Should I install the rear Jammer up front (if so any tips on where)?
ZR3s on that car will be nothing more than a false sense of security, which is worse than no jammer at all.

crazyVOLVOrob
09-22-2009, 11:30 PM
Here is the results of the ZR3 on a C6 corvette
-Chevy C6 Corvette
-Escort ZR3 (2 heads up front, rear head on top of rear plate)
-No front plate
-State Issued plate on rear

http://i36.photobucket.com/albums/e12/crazyVOLVOrob/NEJ1.jpg
http://i36.photobucket.com/albums/e12/crazyVOLVOrob/NEJ2.jpg

LTI Ultralyte (125pps)
FRONT
-1000ft (45mph) and 267ft (18mph) on Driver-Side Headlight,
-JTG elsewhere
REAR
-300ft (14mph) Driver-Side Taillight,
-JFG after

LTI TruSpeed (200.3pps)
FRONT
-800ft (38mph) on Passenger-Side Headlight,
-JTG all over after
REAR
-75ft, and 1800ft(38mph). On Passenger Taillights

Laser Atlanta Normal Mode (238pps)
FRONT
-363ft (20mph) on Driver-side Headlight,
-JTG Center-mass and Passenger-side headlight
REAR
-JFG on Center-Mass,
-Consistent punchthrough 200ft-800ft aiming at either taillight after JFG


Stalker LZ1
FRONT
-272ft on Center-Mass, JTG after
-341ft on Passenger-Headlight
-483ft, 771ft, and 1071ft (42mph) on Driver-Side Taillight
REAR
-150ft(4mph) Center-Mass
-685ft (40mph), 983ft(40mph), 1240ft (40mph) and 1800ft (40mph) on Driver-Side Taillight

TSi+WRX
09-23-2009, 08:28 AM
Here is the results of the ZR3 on a C6 corvette


^ And based on that, I'd say to install the rear head front-and-center - but be sure to also displace the two front heads as wide apart as you can, to minimize the possibility of destructive cross-talk interference.

Truly, get tested, if you can - not only will you then know the absolute strengths and weaknesses of your setup, but also, more importantly, you'll see if the unconventional setup, combined with the limited space you have in that area, will cause interference that would negatively impact performance.

95blklsc
09-23-2009, 09:30 AM
Hey that was my car that was tested with the ZR3s. Thanks for bringing that info over to this thread Rob!

Keep in mind I wasn't using a front plate, if I was I think I would have been totally owned at first shot. The passenger side head was actually a little crooked too. I was surprised with how well it did with all things considered, I had very low expectations for it as well. Keep in mind I think the distance of first targeting the front was 2200 feet or something like that. I was going 30-40 mph so I did have some good warning time if it were a real encounter. That system saved my ass twice going about 25-35 over PSL in the six months it was on the car. :eek:

I have since put on an LI since I wasn't confident in the ZR3's ability to jam in all situations.

I also decided to switch because I just wasn't 100% happy with the radar performance of the SRX in my car, the antenna was just too low to be effective. When it was on the car I had previously, the antenna was much higher and gave much better performance.

You can see what I'm running now in my signature, no complaints here!

I'm actually going up to NH to test the LI's tonight. (they are spaced a good amount wider than the ZR3s pictured)

category4
09-23-2009, 07:38 PM
From what I have seen of the ZR3's, you need to get them as close to the headlights as possible for best results.

velcro
09-23-2009, 09:29 PM
Thanks for the tips everyone, I know the ZR3 is somewhat sucky, but it's a start (and the cost couldn't be beat.

I know I need to add something to beef it up on the front. I still am torn as to whether the best bang adding is 3rd head up front, Veil (on lights and fogs), or both. Does the third head add a lot alone, or am I better with just 2 and Veil.

Stalker I hear you on the false sense of security, and I'm looking to keep a rabbit out front most times, but cut down on my risks when running alone (or get the itch to get on it).

cat 4, I can see myself growing into the LI 4 setup, that's probably where I'm headed someday.

I'm leaning to push the 2 front heads as wide as I can in the grill, rear in the center, and holding off on the Veil for now.

95blklsc
09-23-2009, 09:36 PM
Just put the three heads up front. Mine did decent with just two. Really close shots to the headlights would have been a problem for it though. Although veil is really good stuff I would hesitate putting it on the corvette headlights for one reason, crazing. Any alcohol based product or cleaner tends to make the corvette headlights develop fine crazing and eventually worse and deeper crazing. The headlight assemblies are about 1k each to replace. Go do some searching on the corvette forum on this. A lot of guys think it is from heat but that simply is not the case, especially with a projector HID. Make sure you don't have a front plate on, do a good install of the ZR3 for now and it should give you some level of protection based on how my car did. But save for the LI or blinder. I just tested my LI tonight and it was JTG all the way on my C6 against a PLII.

Stealth Stalker
09-23-2009, 10:09 PM
Does the third head add a lot alone, or am I better with just 2 and Veil.
Well, it's not doing you any good on the rear, so you might as well stick it up front. However no, I wouldn't expect it to make much difference at all. Center mass is probably not going to be your problem, so a center head shouldn't be the solution. However, a center head should at least make you feel better about putting your lateral heads as widely spaced as you can possibly get them.

DrCoke
09-23-2009, 10:50 PM
Those zr3 WILL protect you in MOST cases, but you will get owned down the road if you speed alot. Those zr3 will give you great protection if the Leo was targeting you at over 1,000 ft, but most encounters are at 500ft. That gives you almost no time to slow down before PT occurs. Most jammers have no issue with center mass, its the deadly headlights thats a pain to protect. For anyone owning a car over $30,000, I don't see a big deal dropping $700 for the LI-Dual.

category4
09-24-2009, 04:08 AM
Those zr3 WILL protect you in MOST cases, but you will get owned down the road if you speed alot. Those zr3 will give you great protection if the Leo was targeting you at over 1,000 ft, but most encounters are at 500ft. That gives you almost no time to slow down before PT occurs. Most jammers have no issue with center mass, its the deadly headlights thats a pain to protect. For anyone owning a car over $30,000, I don't see a big deal dropping $700 for the LI-Dual.

I agree, I see so many 50K car with a Cobra in the windshield it drives me crazy.

I had ZR4's on the Vette (came with the 9500ci) and they were pretty much instant PT on the rear during our tests. On the front it was not much better.

Veil on C6 headlights ruins the light output according to Erick. I have never tried it based on Erick's input.

I would go Blinder M27 or LI on the Vette, especially if you speed. You are an instant target if you are flowing with traffic. I have been targeted many times when there were faster cars right beside me. Figure it as the Corvette Tax, you need JTG performance if you are speeding in a Vette (any high end sports car for that matter)!

TSi+WRX
09-24-2009, 08:01 AM
Does the third head add a lot alone, or am I better with just 2 and Veil.
Well, it's not doing you any good on the rear, so you might as well stick it up front. However no, I wouldn't expect it to make much difference at all. Center mass is probably not going to be your problem, so a center head shouldn't be the solution. However, a center head should at least make you feel better about putting your lateral heads as widely spaced as you can possibly get them.

^ That's exactly my reasoning, too. :)

It'll allow the "front" heads to be as widely displaced as possible, while still maintaining good center-mass protection.



Veil on C6 headlights ruins the light output according to Erick. I have never tried it based on Erick's input.

^ To be completely fair, erickonphoenix does tend to use *a lot* of VEIL, and anything more than two coats really start to eat into both light output as well as beam patterning...*and* that was with the old G2 formulation.

But what concerned me about the C5/C6 application was, and I don't remember if it's you who pointed it out to me, cat4 :redface:, is that there's some concern about headlamp "overlens" cracking issues, due to high bulb temperatures.

If that's the case, I honestly don't know what VEIL will do, given that it's going to reject or absorb IR from both without *and* within (remembering that HIR bulbs utilize the wasted IR-wavelength to intensify lighting output).

95blklsc
09-24-2009, 09:46 AM
Does the third head add a lot alone, or am I better with just 2 and Veil.
Well, it's not doing you any good on the rear, so you might as well stick it up front. However no, I wouldn't expect it to make much difference at all. Center mass is probably not going to be your problem, so a center head shouldn't be the solution. However, a center head should at least make you feel better about putting your lateral heads as widely spaced as you can possibly get them.

^ That's exactly my reasoning, too. :)

It'll allow the "front" heads to be as widely displaced as possible, while still maintaining good center-mass protection.



Veil on C6 headlights ruins the light output according to Erick. I have never tried it based on Erick's input.

^ To be completely fair, erickonphoenix does tend to use *a lot* of VEIL, and anything more than two coats really start to eat into both light output as well as beam patterning...*and* that was with the old G2 formulation.

But what concerned me about the C5/C6 application was, and I don't remember if it's you who pointed it out to me, cat4 :redface:, is that there's some concern about headlamp "overlens" cracking issues, due to high bulb temperatures.

If that's the case, I honestly don't know what VEIL will do, given that it's going to reject or absorb IR from both without *and* within (remembering that HIR bulbs utilize the wasted IR-wavelength to intensify lighting output).

While I have not had this problem with crazing on the lenses personally I know someone who has. I actually had him send the part to me to have a material scientist friend of mine who is very familiar with polycarbonate and various other plastics. Since I’m not an expert in the area I might be screwing up some of the terms and/or causes but it will give you the idea I think.

He said it was NOT due to heat in ANY way shape or form. Just feel the lens after the lights have been on, they are not hot. HIDs run at a much cooler surface temperature than a halogen. To further add to that the bulb is behind a projector which will absorb most of the radiant heat.

The cause was a breakdown (think of it as unzipping) of the polycarbonate molecular "chains" which have a few possible causes. One possibility cause is degradation of the UV protective layer over the polycarbonate, sometimes alcohol based solutions. They can significantly degrade this coating and cause UV from the sun to attack the poly. Also, if this UV coating has pits and cracks from use and a alcohol is applied it can directly attack the poly as well depending on the concentrations. In this case molded in stress can start to show up as crazing.

I think people on the Corvette forum blame the adhesive headlight protectors because those are typically put on with a diluted isopropyl alcohol solution. I'm sure some amount of this solution gets trapped under the headlight protector and just keeps eating away at either the coating or the poly its self.

So my only suggestion is to see what the solvent is in VEIL and go from there. Even if it does not cause problems on 99% of cars it could on the corvette headlights because of the poly, the UV layer, or a high level of molded in stress. This isn't something that typically happens overnight either.

TSi+WRX
09-24-2009, 12:28 PM
^ Ah! Thank you for that! :)

I'd give VEIL Guy a direct PM - ask him to weigh-in on the issue.....

VEIL's formulation is proprietary, and is a closely guarded secret, but he should, in being an enthusiast, himself, be willing to comment on whether or not you'd be at additional risk.

One piece of information that I can offer you is that absolute ethanol (100%) will take off VEIL G4 as though it never dried to the surface in the first place. This, however, is no way conclusive proof as to what solvents may or may not be a part of the G4 formulation.

category4
09-24-2009, 03:05 PM
On a C6 I believe the low beams are HID and the high beams are halogen. The problem some member on the corvette forum were having was when they tinted the headlight lens they cracked. I'm not sure if Veil would have the same effect.

Erick said Veil distorted the crisp clean lines the headlamp output had before. After driving the Vette I understood what he means and not sure I can put it into words. The light from the ID's is very clean and sharp right to the edge of the beam. I'm thinking he meant it all just kind of faded away and was not as clean and crisp at the outer edges of the beam.

Either way I was not willing to Veil the headlights, but did Veil the tail light assemblies. The problem with trying to protect the Vettes is that they are so wide and the lights front and rear are on the extreme edges of the vehicle. It takes a very good jammer to adequately defend the entire front or back, if the shooter is knowledgeable of this info, or lucky!

TSi+WRX
09-25-2009, 07:51 AM
Erick said Veil distorted the crisp clean lines the headlamp output had before. After driving the Vette I understood what he means and not sure I can put it into words. The light from the ID's is very clean and sharp right to the edge of the beam. I'm thinking he meant it all just kind of faded away and was not as clean and crisp at the outer edges of the beam.

Yep, that's a definite.

Even with only one thin coat, I see cut-off distortion (that word is too harsh in connotation - it's really, at the one thin coat, just a slight blurring of the cut-off).

I have no doubt that the better the factory optics the more that this will be noted - however, it's important for this to be put into perspective, in that just a little such blurring should have little to no effect on either the vehicle's driver or oncoming traffic.

But given erickohphoenix's typically heavier hand at VEIL'ing, I think that the end-result of his attempts would have made the light noticeably less usable.

My speculation is that such distortions come about because VEIL is, in its current form, non-homogeneous.



The problem with trying to protect the Vettes is that they are so wide and the lights front and rear are on the extreme edges of the vehicle. It takes a very good jammer to adequately defend the entire front or back, if the shooter is knowledgeable of this info, or lucky!

+1.