View Full Version : Mounting ideas?
msh441
11-29-2004, 10:20 AM
I'm pretty commited to using a RAM mount for my new detector.
I've used one with my GPS V for a year now and like how sturdy it is. The GPS arm comes off a ball mounted on the back of the front brake lever clamp. Due to tight sportsbike cockpit, a second arm and plate off the clutch side seems like it'll be an efficient use of space.
Curious what other two wheeled users are doing.
Mike H
Radar Roy
11-29-2004, 10:37 AM
I also use the RAM Mount for my GPS, but for radar detectors I like the "Spider" Mounts.
The only issue I have had with my RAM mount, was for some reason the bolt working lose while riding. Had to use some locktight to keep that from happening
msh441
11-29-2004, 02:52 PM
I like the stem bolt hole mounts too.
Unfortunately in their efforts to be different, Triumph uses a closed machined stearing head bolt... so no hole.
Mike H
I've my Bel 660R/975R installed in my yamaha FZ600S and I just need an earphone. All is concealled. It works fine.
Radar Roy
02-07-2005, 03:05 PM
We had installed the 975R too on motorcycles, but one good rain storm is all it takes to short out the control head
The Bel 660R control panel for bike is waterproof and usually are installed in covered places.
Radar Roy
02-07-2005, 11:51 PM
Are these the units that Target International sells?
Yes it is the Bel Target 660R. To tell you the truth, it works fine. I think is the best RD for Europe.
Radar Roy
02-09-2005, 10:34 AM
I've seen them on the net, they do a nice conversion to the unit!
Not available in the states
If you need any unit, I can buy and send you to the U.S.A.
radarduck
05-03-2005, 11:33 AM
I've just completed a stealth moutning of my new RX65 inside the fairing of my BMW K1100LT. My purpose in mounting it this way was threefold: 1) I didn't want cops to see a RD sitting on a shelf or on a handlebar mount out in the open in the event I'm pulled over, 2) I wanted a semipermanent mount which was not obvious to thieves and 3) I wanted something waterproof/resistant since the RX65 isn't meant to be exposed to the elements.
The way it's moutned I do give up laser detection and the abiltiy to play with the settings while riding but that's OK with me.
I built a custom box out of black ABS and clear acrylic and mounted it inside the fairing. (It's a home job using black ABS stock and expoxy - nothing fancy but not too bad looking.) The box has just enough room to fit the RX65 with the power supply and earphone jack hooked up. The front and back are clear acrylic. The back is clear so that I can see the display from my normal riding position. It also keeps it in the shade so the display is easier to read. Since it's buried in the fairing and mostly black, someone else would have to look for it to find it when the bike's parked. I've read complaints that the RX65 display is angled upwards which makes it more difficult to read when windshield mounted in a car. For my application, this turned out to be a plus as it makes it an almost perfect angle for easily reading the display form my normal riding position.
The top of the box comes off so that I can move the RX65 over to my car as needed.
I made the front of the box out of clear acrylic too in case I ever change to a mounting position where I can use the Laser detection features. I'm sure the mounting position will also have some (hopefully small) impact on radar detection but that's why I got the best one out there.
Since I didn't want to deal with the hassle of earphones, I looked into getting a Radar Screamer which looks like a cool product but decided to perform some experimentation and found that a $11.49 piezo siren from Radio Shack would suit the same purpose when wired directly to the RX65's headphone jack. Since I have the RX65 set to automute, it gives me all the notice I need that I'm being lit up without being too obnoxious.
It's power is controlled by a generic BMW OEM stock dashboard switch which looks completely normal and discrete mounted in the dash. Nobody would ever guess that it's for a RD.
BTW: I also like the voltage meter function of the RX65 and, at least for now, have that set as the display mode.
I'll post some pictures in here later so you can see what it looks like.
radarduck
05-04-2005, 12:51 PM
Here's a couple of pics:
How it looks from riding position:
http://sumdumguy.home.comcast.net/images/rx65install.jpg
This is kind of a closeup with a flash picture:
http://sumdumguy.home.comcast.net/images/rx65install2.jpg
Radar Roy
05-04-2005, 02:29 PM
Very cool and clean install, great job man..