PDA

View Full Version : Need DEEP Nerd/Engineer Help with a USB to Serial conversion



STiMULi
11-30-2009, 01:34 AM
Please read carefully before you reply because it is not what you might think first off.

Do not make assumptions on PC connectivity

I will explain more about the complete application later but I want to concentrate on the specifics 1st.

There is a GPS that has a NMEA USB output that I want to harness the information from and connect to a NON PC serial port device.

AGAIN IT IS A NON PC DEVICE

So what I want to know is if anyone has ever taken a USB output (NOT FROM A PC) and converted it to a straight SERIAL.

I would like to take this USB connection and connect it to a PC with a TRUE (DB9/25) COM 1,2,3,4 SERIAL port on a PC to read the NMEA sentences as a means to test and verify connectivity.

I know I could just connect the USB to the PC and all would be well but the ultimate device that the USB would be connected to is a DB9 SERIAL port that can handle high speeds but WILL NOT BE A PC and drivers can not be loaded into it.

I know there are USB to serial cables that will take care of the physical connections and that may be the answer but under normal circumstances they are to be used from a USB PC to a serial device and the require a driver to be loaded on the PC.

This application that I am speaking of can not use a driver or ultimately a PC for connection.

GPS---w/USB---->-----SERIALPORT---ON A PC (for testing)

Now for the ultimate application...

I am trying to see if there is a way to take a GPS with a dedicated NMEA USB output (these are fairly uncommon and usually do not have displays) and then connect it to a Uniden BCD996T/XT for control.

GPS---w/USB---->-(CONVERSION CABLE)->----SERIALPORT---BCD996T/XT

The application goes a step further but I will get into that as (if) the discussion progresses.

Any ideas?

I will be testing the USB output later this week or early next week.

If you tell me to get a USB to Serial cable and plug the USB into a PC I will give you unhappy faces and make fun of you for not reading the post :)

voyager7
11-30-2009, 09:30 AM
I see where you are going with this.

This forum might be able to help.

RadioReference.com - Scanner Frequencies and Radio Frequency Reference (http://www.radioreference.com/)

I have a buddy that is a programmer and a computer geek that has done non pc interfaces before. I sent him your post to see if he can help any.

voyager7
11-30-2009, 09:49 AM
Have you seen this?

MobileConnectingAGPSReceiver < UnidenMan4 < TWiki (http://info.uniden.com/twiki/bin/view/UnidenMan4/MobileConnectingAGPSReceiver)

A Garmin 176C has the capability to connect this way. (I have one).
Almost any older Garmin will connect this way.
Buying one (an older Garmin) might be the better way to go.

STiMULi
11-30-2009, 11:40 AM
Have you seen this?

MobileConnectingAGPSReceiver < UnidenMan4 < TWiki (http://info.uniden.com/twiki/bin/view/UnidenMan4/MobileConnectingAGPSReceiver)

A Garmin 176C has the capability to connect this way. (I have one).
Almost any older Garmin will connect this way.
Buying one (an older Garmin) might be the better way to go.

This is the killer...



Compatible GPS receivers


You can connect your scanner to any GPS receiver that meets the following criteria:

Outputs NMEA-0183 v3.01-compliant location data
Outputs both the Global Positioning System Fix ( GGA ) and Recommended Minimum Specific GNSS ( RMC ) data sentences
Provides a serial data (RS-232) connection
I already have a serial port based GPS it is an old Garmin GPS III color I split the XMT side for use for both APRS and the 996. For APRS it is real cool as it shows the moving location of the other stations in my area.

I really want to use the Cheetah C50 as it has the NMEA through the USB. Cheetah thinks there is a way and I have read some material on the web of converting the output of a USB for this purpose but it was all homegrown. It spoke of TTL to serial conversion.

I would really love to comminucate with a Cheetah engineer about this.

We will see soon though...

The Chariot
11-30-2009, 01:25 PM
The USB host must have a driver for serial. Remember, USB is simply a bus which transmits raw data. The host much know how to use that raw data, so it has to have a serial over USB driver. Odds are slim the GPS has a driver for it, they tend to make the OS kernel pretty stripped down for size reasons. If its a Windows mobile based GPS (many are) then the driver is built in and you can use one of those cables. If Linux based you may get lucky and they compiled support in the kernel. If its something else.... who knows.

Don't know about your specific GPS, but most of them use a FAT formated drive style interface/driver on the USB port though some of the newer units also support COM interfaces.

STiMULi
11-30-2009, 01:38 PM
The USB host must have a driver for serial. Remember, USB is simply a bus which transmits raw data. The host much know how to use that raw data, so it has to have a serial over USB driver. Odds are slim the GPS has a driver for it, they tend to make the OS kernel pretty stripped down for size reasons. If its a Windows mobile based GPS (many are) then the driver is built in and you can use one of those cables. If Linux based you may get lucky and they compiled support in the kernel. If its something else.... who knows.

Don't know about your specific GPS, but most of them use a FAT formated drive style interface/driver on the USB port though some of the newer units also support COM interfaces.

We will see. I just got off the phone with RacerX and he seems to think that the higher-end USB to SERIAL cables might do the trick. I hope so!

voyager7
12-01-2009, 08:50 AM
Just wondering why the Cheetah?

voyager7
12-03-2009, 03:06 PM
My friend said to try here.

USB Connectivity, USB Adapters, USB Cables (http://www.bb-elec.com/productcat.asp?topLevelid=16)