View Full Version : Out of Level by 1.59 Degrees - WWYD?
swarga
09-14-2010, 09:28 PM
While doing my 9500ci installation I noticed that the "nose" of my C6 is shaped somewhat like a beak: the bottom surface slopes downward from the sides in a very slight V shape, and the front surface is curved outward. I took a few measurements, dusted off my high school trigonometry, and calculated that the slope of the nose is ~1.59 degrees. Thus, if I just slap the heads to the underside of the nose using mounting tape they will be tilted by ~1.59 degrees.
I know the Escort spec is +/- 2.5 degrees, and ISTR that Radar Roy did some testing of ZR4s and determined that an even narrower range was optimal. What Would You Do?
barryswanson
09-14-2010, 09:52 PM
Dial them in level if you can.
chriskohtc
09-14-2010, 10:08 PM
I think there're shims you can buy. You should be able to find them at a Home Depot or Lowe's. They should have it under the hardware aisle.
Alternatively, you could always do a DIY with these....
http://www.lowes.com/pd_247891-143-PP836-55L_4294808859_4294937087?productId=3133327
Edit: These're more expensive, but are made of Aluminum. http://www.thefind.com/cars/info-4-degree-shims
swarga
09-14-2010, 11:35 PM
I think there're shims you can buy. You should be able to find them at a Home Depot or Lowe's. They should have it under the hardware aisle.
Alternatively, you could always do a DIY with these....
http://www.lowes.com/pd_247891-143-PP836-55L_4294808859_4294937087?productId=3133327
I don't know if I could bear the thought of installing toilet parts on my car. :D
These're more expensive, but are made of Aluminum. http://www.thefind.com/cars/info-4-degree-shimsWouldn't these just exacerbate the problem? If the heads start out tilted 1.59 degrees CCW, and these add a 4 degree CW tilt, the next result is a 2.41 degree CW tilt, right? Or is the amount of tilt adjustable somehow?
Edit: I changed the search terms and found some 2 degree shims. If I can find some the right size this might be just the ticket - thanks for the idea!
DrCoke
09-15-2010, 12:09 AM
I use shims from HomeDepot and double sided 3m tape from the auto store.
Hunter
09-15-2010, 01:13 AM
I use shims from HomeDepot and double sided 3m tape from the auto store.
same here.3M tape works great!!
radarrob
09-15-2010, 02:44 PM
3M and brackets.homedepot +1!:cool:
swarga
09-16-2010, 09:25 PM
OK, I went to Home Despot and found some plastic shims. Here's what it looks like without the shim:
http://i51.tinypic.com/z5loh.jpg
And here's what it looks like with the shim in place:
http://i56.tinypic.com/2zpmsy0.jpg
Now is it close enough? LOL!!!
chriskohtc
09-16-2010, 11:52 PM
Plastic shims? Did you end up getting the "toilet" parts?!!?!? Haahaha.
swarga
09-17-2010, 12:09 AM
Plastic shims? Did you end up getting the "toilet" parts?!!?!? Haahaha.
Nope! :D
The angle on the toilet shims is too steep. These are cabinet shims, similar to the standard wooden ones only they're made of plastic. Unfortunately, I can't find the ones I bought on the Home Despot web page, but here (http://www.amazon.com/SHIM-COMPOSITE-SHIMS-PACK-Misc/dp/B002LCWGSO) they are on Amazon.
barryswanson
10-07-2010, 06:15 AM
Did you end up getting your heads mounted swarga?
swarga
10-19-2010, 10:53 PM
Did you end up getting your heads mounted swarga?
No, I've decided to hold off on those a bit longer. The brackets are all leveled up and ready to go on, however:
http://i56.tinypic.com/2le5poo.jpg