PDA

View Full Version : MEM-TEK modifications on ZR4



RobInAlbany
10-20-2010, 10:36 AM
I read a copy of older threads on how MEM-TEK modified some ZR4s and improved their performance substantially. I own a ZR3 and have a degree in engineering so I am very handy with electronics and would like to make the same kind of mods.

Does anybody know if MEM-TEK disclosed his mods somewhere?

Before reading this I was considering making some mods of my own. I could use an JR45 splitter coming out of the control module and use that to drive a third head that I could make myself using some very powerful 904nm diodes I have around. This head would need it's own driving stage though, no biggie, just BJT to N channel MOSFET to diode should do it since the jamming algorithms are only running at about 100Hz. I would just need to find which wire does the firing coming from the control module.

srtga
10-20-2010, 11:12 AM
Everyone who messes in that stuff dissapears...

Do you really want to end up a statistic?

Sandman76
10-20-2010, 12:57 PM
Everyone who messes in that stuff dissapears...

Do you really want to end up a statistic?

SHHHH! The first rule of Mod Club is, "We don't talk about Mod Club."

Won Hunglo
10-20-2010, 06:24 PM
Don't do it! They will cut your head off & send it to a mexican policia depatment. Anyone that mods a jammer meets the same fate, never to be heard from again.

category4
10-20-2010, 06:27 PM
As far as I know only MEM-TEK and Escort know for sure what the modifications were.

Lucky225
10-20-2010, 06:31 PM
As far as I know only MEM-TEK and Escort know for sure what the modifications were.

And only they know where to find his body.

srtga
10-20-2010, 06:58 PM
I hear The Chariot's in another dimension with Solions porn collection and a PL2. Mem-Tek's somewhere in the future and has some kind of weird gender issues...

I'd be careful fooling with that stuff. But hey, do what you want...

mikered30
10-20-2010, 09:21 PM
What ever happened to MEM-TEK?

swarga
10-20-2010, 09:25 PM
Everyone who messes in that stuff dissapears...

Do you really want to end up a statistic?

I heard that a set of MEM-TEK ZR4s killed President Kennedy, but the guy that told me that recently died under mysterious circumstances...

Won Hunglo
10-20-2010, 09:46 PM
What ever happened to MEM-TEK?

He was lured to the Escort lab and then...

http://ghostofbataan.com/image2/pict2.jpg

niran916
10-20-2010, 10:15 PM
What ever happened to MEM-TEK?

he's been golfing.

CJR238
10-20-2010, 10:24 PM
I read a copy of older threads on how MEM-TEK modified some ZR4s and improved their performance substantially. I own a ZR3 and have a degree in engineering so I am very handy with electronics and would like to make the same kind of mods.

Does anybody know if MEM-TEK disclosed his mods somewhere?

Before reading this I was considering making some mods of my own. I could use an JR45 splitter coming out of the control module and use that to drive a third head that I could make myself using some very powerful 904nm diodes I have around. This head would need it's own driving stage though, no biggie, just BJT to N channel MOSFET to diode should do it since the jamming algorithms are only running at about 100Hz. I would just need to find which wire does the firing coming from the control module.

Wont work, they need to be timed perfectly. The firing sequence isint just in the control module.

RobInAlbany
10-21-2010, 03:26 PM
you sure about this? how do both of the transceivers know to fire at the same time? if they were independent wouldn't they have cross-talk?

To be sure I am going to try putting a scope on the output pins on the control module and look for the approximately 100pps firing. I will just need a way to get it to fire. I noticed that if you disconnect one of the heads while the power is on it sometimes alerts to laser.

CJR238
10-21-2010, 05:36 PM
you sure about this? how do both of the transceivers know to fire at the same time? if they were independent wouldn't they have cross-talk?

To be sure I am going to try putting a scope on the output pins on the control module and look for the approximately 100pps firing. I will just need a way to get it to fire. I noticed that if you disconnect one of the heads while the power is on it sometimes alerts to laser.

Not shure if its the right or left head (left?) but one head is master and one is slave.

roninmd
10-22-2010, 10:50 AM
I will just need a way to get it to fire Use a tv remote and press the vol. http://www.youtube.com/watch?v=_oMig9E-pcA

If you come up with something, send me a schematic. I know you will need:
(8) 904/905nm laser diodes.
Better Optics.
a laser driver to drive your heads so that they don't burn out.

And beware that you don't look at the diode when it's active because even if you don't see the light it may cause retinal damage. Infrared is the radiant form of heat and when concentrated by your eyes lens, you have a bad situation in your eyes.

A simpler thing would be to replace the InfraRed LEDs with brighter InfraRed LEDs.

RobInAlbany
10-23-2010, 06:00 PM
Thanks

Yea, replacing the diodes would definitely be easier, I wonder if that is what MEM-TEK. However, I don't know how much current the ZR3 amplifiers can supply. Some of these laser diodes can draw up to 1A! but thats peak current of course, because it is pulsed, otherwise the diode would burn out if it was continuous current. That's why I want to start from the ground up with an amplifier that can handle really high current. Here's an ultrasound amp I made awhile back:

http://static.ak.fbcdn.net/rsrc.php/z4OG5/hash/7qkbs3nb.swf?v=1417102431269&ev=0

Also, I really didn't want to open up my heads because I'm worried about breakin them. Ideally I want to just plug a splitter into the control molude and than have an extra head that I made coming out of that, using the original heads to sense the laser.

I bought a splitter last night and brought home a data acquisition unit from work so I record the exact signal that is coming out of the control module, and if there is indeed a pulse that I can use for my extra head that I'll make. But I am having trouble triggering it reliably with my remote, I have a curtis tv (sylvania subliterary) what is the one you use in the vid?

roninmd
10-24-2010, 12:49 AM
Hey, that's some good work with the ultrasound device. The remote I used belongs to a 50 in LCD TV made by Vivitek.

If the heads are similar to the ZR4 heads. The tabs are easy enough to open the heads. Don't worry about the weather proofing it's designed in the housing. You shouldn't submerse them in water but they could handle rain.

Tell me what your findings are. I'm seriously interested in this mod stuff.

roninmd
10-25-2010, 02:20 AM
Why don't you make this simpler. Create a separate head with your 904nm diode lasers array with proper power driver. Use some transistor relay to activate the laser head when one of the LEDs in the zr3 head is on.

What I'd like to do is find a way to get my head light to modulate with the zr4 firing. There's Lots of IR coming out of that headlight. Headlight modulation is legal in all 50 states because it's supposed to make motorcycling safer during the day. At night, the modulation must be turned off. What do you think will happen when the cop's photodiode detects the pulses of IR coming off the headlight.

RobInAlbany
10-25-2010, 07:52 AM
good thought. however I would still need to trigger the zr3 to be sure that my head was reading it right. and then it would always be subjected to interference and noise from ambient light. using the pulse from the control module would be the most reliable method.

the headlights might not be able to flash that quickly. from what I am reading its between 100~200pps which isn't that fast but the pulses are only about 100nsec long. an incandescent light bulb has a much slower response time.

roninmd
10-25-2010, 04:57 PM
To trigger the ZR3 have you tried making your own pulsed 904/905 nm laser to shine on the photodiode? The photodiode is on the outer side of the head.

From what I read about Mem-Teks mods. All he did was change the IR LEDs with Brighter LEDs and perhaps added a filter to the optic section to filter in the 905/905 wavelength specifically. Adding the filter; however, reduced the optic's sensitivity slightly.

He may have also changed the MOSFET that ran both front shifters.
When I spliced my front shifters with a phone coupler, I did not verify the orientation of the RJ11s so I blew out the MOSFET in the control module and a capacitor in the shifter head.

Luckily a family member was an engineer and replaced the components; however, he didn't have any MOSFETs available and wound up using another type of transistor.

Activating the shifters with tv remote and looking at the shifter heads through the Iphone clone camera, it seems the shifters are brighter. Before there was variability in brightness I must assume came from the field effects of the MOSFET. It's lost now with the new transistor installed which I must assume makes the LEDs just go on and off and not vary in brightness.

Before:

http://www.youtube.com/watch?v=_oMig9E-pcA

After:

http://www.youtube.com/watch?v=w1RW8usj5OQ

I don't remember MEM-TEK making a laser diode array. These were much more simpler mods that anyone with a soldering iron and a bit of theory can experiment with.

Another must have MOD, is to add a diode in case a user crosses the wires when splicing the cables.

barryswanson
10-26-2010, 06:20 PM
Interesting stuff. I wonder why in the first vid one of your heads was so dull? I remember filming my zr4's fire and they where both appeared even in output.

roninmd
10-26-2010, 09:21 PM
Not sure. It's possible the guy who had it before me had issues with it. Or they fired independently depending on which sensor got the most IR. Or it could be the way the front shifters are aligned.

Front shifters work great before albeit a little dimmer. However the Rear shifter didn't respond when i got it.

I popped open the rear shifter and guess what I found:

http://i109.photobucket.com/albums/n80/roninmd/th_Image0581.jpg (http://s109.photobucket.com/albums/n80/roninmd/?action=view&current=Image0581.jpg)

Rust and corrosion everywhere but mainly around the receiver section.

The internals are covered by a metal shield so I'll have to desolder the shield to see what's else is messed up.

The display module did not show any malfunction but it's obvious now why you should tape your heads.

I'll post more pics of this repair when I can get my hands on a soldering iron and solder remover.

roninmd
10-28-2010, 01:24 AM
Sorry no pics. I unsoldered the metal cage that houses the photodiode circuitry. The photoLEDs weren't getting any current because a resistor broke off. Lots of teeny tiny capacitors and resistors on that board. Saw a couple of pads that were missing a capacitor here and a resistor there.

We didn't know what went where until we looked up one of the chips and followed the paths. It looked like a NEC linear video amplifier (http://parts.digikey.com/1/parts/466296-ic-video-amp-diff-8-ssop-upc1663gv-e1-a.html) . From that, we gathered that the dielectrics that popped off were capacitors that fed in and out of the 1663 chip.

Added the caps and then tested it. It works good now. Now I know when I'm getting hit from behind.

RobInAlbany
11-28-2010, 09:47 AM
Sorry it took me so long to reply to this thread again. And very funny post from everyone before, I guess MEM-TEK is not here right now. Anyways, If anyone does own a MEM-TEK modified Shifter it would be great if you could share some photos of it. Maybe I could reverse engineer it. Not for profit of course because it wouldn't be my own design, but if it works out and if anyone else wanted theirs modified I would be happy to do it for them if they could spare just the money for parts.

In the mean time I have been continuing developing my own mods. My ideal is to use the pulse train that is being sent to the heads and use it to drive another head with a more powerful laser diode. This extra head would fire exactly like the other LED heads but just with more power. I would essentially be using the ZR3s as a trigger, since they have great laser detection adding more power should make a good jammer.

The amplifier I had in mind was something like this. The pulse source would either come from the control module, or I could actually put the laser diode inside the old heads and use the pulse that is being sent to the LEDs as a pulse source. V supply should be just he 14V coming from the alternator. But when I looked at the voltage coming from the control module it was 10V, this means there must be a regulator inside the control module. I am not sure what the current rating is on the regulator and it might not be enough for driving the laser diode
http://i1198.photobucket.com/albums/aa451/nesbir/LaserDiodeDriver2.jpg

When samq45 was kind enough to test my setup, I had a splitter running from the control module to a data acquisition unit so I could record the signals that are used to communicate. I had the power and ground switched so it reads -10V, but it looks like the white wire next to the positive power wire carries the pulse (the cable has 4 wires, power and gnd on each side and two white wires in the middle). You can see in the left that at first the zr3s were firing and then samq45 stopped shotting and the pulse coming from the control module stopped. and on the left is a time expanded view. The ptp voltage on this isn't very high, it may be that this is just a drain on the 10V bus that I am seeing. So the pulse might be generated inside the head. In that case I should be able to use pulse being sent to the LED's inside the head to trigger my laser diode driver and the laser diode from an old LPP head samq45 was kind enough to give me
http://i1198.photobucket.com/albums/aa451/nesbir/PulseTrain2.jpg

again, if anyone has a mem-tek mod'd zr3/4 some pictures of the inside would be great!

roninmd
02-02-2011, 03:40 AM
Great work on the schematic. I'll have the family engineer take a look at it. This stuff looks way more advanced than what Mem-tek was doing.

I'd keep the V supply separate until you know exactly how much juice your separate head and control module will take. You should be able to figure that out. Burning out the control module and then having to resolder the caps is a pain in the neck.

If it were me, I'd take a picture of the control modules circuits, noting the components and have replacement parts ready before even using the bus as a v supply for that extra head of yours.

By the way, checkout the wireless sensor bar for the wii. http://s.shld.net/is/image/Sears/05892811000?hei=600&wid=600&op_sharpen=1
It's just an IR LED array but you could totally use the housing for your extra head.
It's on ebay for about 7 bucks but you can get it cheaper on overstock, or amazon.
It's got enough room in there for your laser diodes and then some all within a sleek design.
Your circuit or part of it is probably in that board already so you probably don't have to do much to make it work out.

RobInAlbany
02-02-2011, 10:51 AM
I have actaully done an entire ramafication of this circuit. Sorry for not updating sooner. Basically the OSRAM SPL90-3 laser diodes are over powered and they burn out if turned on for too long. I think the maximum pulse width is about 40nm. So what Osram recommends is using a discharge capacitor. Basically by using the correct C value, you ensure that there is only enough current to run the laser diode for only 40nm. I didn't do the calculation yet. You will have to google for the datasheet. there is a graph of current versus voltage. Integrating under the curve you can figure you how many coulombs you need. And then by picking the right R1 value you will have a charge time on 1/(RC) which will be much longer than the pulse (1-10ms) so you don't have to worry about it bring on too longer.

For V supply you can just use 14V. The zener diode is setting the charge voltage of the discharge cap. For the pulse source, there is a thread on here where someone took pictures of the insides of the ZR3 and ZR4. in there you can read the part number of a gate driver. that part would be perfect for driving this thing! I learned in my test with samq45 that the wires from the control module carries no signal.

http://i1198.photobucket.com/albums/aa451/nesbir/diodedriver.jpg