Page 2 of 2 FirstFirst 12
Results 11 to 18 of 18

Thread: Hardwire

  1. #11

    Default

    Is the sunroof switch on the ceiling? If not, better go the way everyone else is suggesting.

    If the switch IS on the ceiling, you can access the wiring to it very easily and it will operate the way you want it to. Let me know.

  2. #12
    Newcomer
    Join Date
    Nov 2005
    Posts
    23

    Default

    yes, the sunroof switch is on the ceiling.

  3. #13

    Default

    There is probably a map light up there near the switch. The lens should come out easily for bulb replacement. Once you remove it, see if it reveals another screw or anything that will allow you to pop the whole assembly off.

    Now, look for the wiring that goes to the switch for the sunroof. Make sure you're not on the sunroof motor side of the switch. Unplug the switch.

    Black or Green is probably ground, one of the solid reds is probably 12v. Turn the key to the ON position. Try touching the two wires of your passport cable to the pins in the plug that the switch goes into. If you touch the wrong ones, the passport is protected from being damaged. You'll know you've found the right wires when it powers on.

    Dont accidently bridge any of the pins of the switch plug as this will possibly cause a short.

  4. #14
    Power User
    Join Date
    Aug 2005
    Location
    Southlake, TX
    Posts
    4,136

    Default

    something about that just doesnt sit right with me... because you also have to find a place to mount the box with the power and warning LEDs and the ever wonderful mute button, it must be within 3ft of where youre drawing power unless you extend the wire and after that where will you hide the 10ft of wire going between the box and the RD?(you could cut it and make it shorter but that takes some effort cuz the strands are so small, trust me my friend did the same thing except he just extended his cig lighter port)....... and I dont know whether youre going to get enough current from the roof power wire, its not just about volts, amps count too... and if you draw too much for the RD you might blow the roof fuse when you try to open/close the thing.......

    if you wanna keep it up there tap it to a, if you have one, electronic RVM (like the ones with a digital compass and temp) or something like that.......... youre certainly welcome to try it dont let me stop you, if you go with this post the results and well see what happens

  5. #15
    Experienced
    Join Date
    May 2006
    Posts
    264

    Default

    Quote Originally Posted by Arashi666
    something about that just doesnt sit right with me... because you also have to find a place to mount the box with the power and warning LEDs and the ever wonderful mute button, it must be within 3ft
    Why do you need the mute button with the Automute feature? Even so, someone posted a schematic that said you just had to momentarily ground one of the outer pins to mute the alert.

  6. #16
    Power User
    Join Date
    Aug 2005
    Location
    Southlake, TX
    Posts
    4,136

    Default

    Quote Originally Posted by Radar_Dick
    Quote Originally Posted by Arashi666
    something about that just doesnt sit right with me... because you also have to find a place to mount the box with the power and warning LEDs and the ever wonderful mute button, it must be within 3ft
    Why do you need the mute button with the Automute feature? Even so, someone posted a schematic that said you just had to momentarily ground one of the outer pins to mute the alert.
    i just mentioned that since its a eature that happens to be in that box..... besides some people (myself included) dont like the auto mute feature because you might miss an alert if youre not paying attention before it lowers the volume on the alert

  7. #17

    Default

    If you look at the link he provided that shows the cable he bought, he doesn't have the "box" with the LEDs and mute button.

    Also, if there's enough amperage to open the sunroof, there's enough to run the detector.

  8. #18
    Power User
    Join Date
    Aug 2005
    Location
    Southlake, TX
    Posts
    4,136

    Default

    ok so i missed that memo........... but you still gotta make sure to tap the wire in the right place.... because i still think between the switch and motor that there will be no power until the circuit is closed (ie. when the switch is pressed)

 

 

Similar Threads

  1. Hardwire V1
    By Solitaire in forum Valentine One
    Replies: 2
    Last Post: 12-06-2009, 12:17 PM
  2. V1 hardwire
    By Scott8659 in forum Valentine One
    Replies: 4
    Last Post: 07-08-2009, 01:20 PM
  3. hardwire
    By beeesmitty in forum Radar Detectors - General
    Replies: 2
    Last Post: 06-12-2009, 09:41 PM
  4. bel hardwire??
    By jdreynss in forum Beltronics
    Replies: 5
    Last Post: 08-14-2006, 03:30 PM
  5. Hardwire help!!!
    By nickmv in forum Radar Detectors - General
    Replies: 3
    Last Post: 06-12-2006, 10:19 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •