Beltronics STi Driver Ramp up fix

[allyoops]

The Cheetah Radar Detector Interface for Beltronics STi Drivers with the ramp-up fix is now available.

[MEM-TEK]

Oh, isn't that special! A lot of people have been waiting for this for quite a while. Good job!

[GTRstikya]

The Cheetah Radar Detector Interface for Beltronics STi Drivers with the ramp-up fix is now available.

Does it still have that KA band 1 second alert delay, or is this been alleviated in the upgrade?

[GTRstikya]

The Cheetah Radar Detector Interface for Beltronics STi Drivers with the ramp-up fix is now available.

Does it still have that KA band 1 second alert delay, or is this been alleviated in the upgrade?

Either way, I still loved it. And would buy another if you'd come out w/ an interface for the STI-R.

[KaPro]

The ramp up fix put some giddyup in the Ka response time.

[rsatmans]

The Cheetah Radar Detector Interface for Beltronics STi Drivers with the ramp-up fix is now available.

Does it still have that KA band 1 second alert delay, or is this been alleviated in the upgrade?

Either way, I still loved it. And would buy another if you'd come out w/ an interface for the STI-R.

X2

[allyoops]

Does it still have that KA band 1 second alert delay, or is this been alleviated in the upgrade?

I think I've posted about this elsewhere before but there are no time delays on any of the compatible radar detectors............provided you have the detectors', menu items set up correctly.

With the STi driver, the critical thing to get right is the volume level - it needs to be at about 6.5 bars (out of 7), the voice needs to be OFF and the power on sequence set for PwrOn FST.

Some times you may need to adjust the volume level slightly (by a fraction of a bar up or down) on an individual STi Driver due to manufacturing variances.

I just had a PM about delays on an X50 and my answer is exactly the same. There are no delays provided you set up the detector menu as we describe in the manual and insert pages.

You can see all the detector settings on this page:

SpeedCheetah.com - detector settings

[mgiara]

I was driving from town to town yesterday and encountered a Ka band speed trap.
As I was coming around a bend, a mini-van sparatically flashed his lights at us from the opposite side of the road. Obviously, an alert of a speed trap coming up.
I had my STi driver mounted and on, but it didn't alert until I turned the bend, and the RD went from silent to full signal.
Question 1: How close do I have to be for the LEO to get a reading on my speed?
Question 2: How can I check the software version to check if I already have the Ramp Up Fix?
Question 3: How do I update the RD if I need the fix?
Thanks in advance!

[RoadWarrior/RW]

I was driving from town to town yesterday and encountered a Ka band speed trap.
As I was coming around a bend, a mini-van sparatically flashed his lights at us from the opposite side of the road. Obviously, an alert of a speed trap coming up.
I had my STi driver mounted and on, but it didn't alert until I turned the bend, and the RD went from silent to full signal.
Question 1: How close do I have to be for the LEO to get a reading on my speed?
Question 2: How can I check the software version to check if I already have the Ramp Up Fix?
Question 3: How do I update the RD if I need the fix?
Thanks in advance!

My STI is built in Aug '06 and never ever needed and done any ramp-up fix or any other technical service, over 130,000 miles with this very STI.

Q2: while powering on, hold all 3 buttons down until you will see that AxMx software version, sometimes you need to do it couple of times until you finally get it right. More here: https://www.beltronics.com/manuals/sti_manual.pdf

Q3: send it out back to Beltronics, never done it so can't comment on this one!

Q1: my STI is got a slow and fast ramp-up alert, when it's fast I'm already in the cruiser's range, when it's slow normally I should be outside his range but as soon as I get one such alert I treat it very seriously and slow down right away, also you gotta learn where the falses are so you will know to distinguish btwn a real and a false alert.

Chris

[MEM-TEK]

I was driving from town to town yesterday and encountered a Ka band speed trap.
As I was coming around a bend, a mini-van sparatically flashed his lights at us from the opposite side of the road. Obviously, an alert of a speed trap coming up.
I had my STi driver mounted and on, but it didn't alert until I turned the bend, and the RD went from silent to full signal.
Question 1: How close do I have to be for the LEO to get a reading on my speed?
Question 2: How can I check the software version to check if I already have the Ramp Up Fix?
Question 3: How do I update the RD if I need the fix?
Thanks in advance!

When the bar graph reaches full strength, then you are really close to or are in range of the radar gun, assuming that the radar gun is set for max range.

To check firmware (yours is A6M9 as I recall, same as current units), first power off your STi. Hold down the Volume and Sensitivity buttons and, while holding these two buttons down, press the power button. Release the buttons when "RESET" is displayed. Then the firmware version will be displayed. Actually the firmware version indicates the specific hardware (display and display board) used within your STi, so even if it is flashed with the audio ramp-up fix firmware it still will come back displaying A6M9.

Your STi doesn't have the ramp-up fix, but it does have the three stage audio ramp-up which was introduced before the full audio ramp-up fix became available at the end of last year. You can send it to Bel to get it flashed with the ramp-up fix if you want.