Page 1 of 2 12 LastLast
Results 1 to 10 of 14
  1. #1
    Newcomer
    Join Date
    Jan 2007
    Location
    UK
    Posts
    35

    Default Laser sensor inside headlight ?

    Hi,
    just bought an LPP for my bike (ZX12). Don't know wether this is stupid or not but I was wondering if locating the sensor inside the headlight was a good or bad idea. Would the sensor still be effective, would the lens be a problem or would it get to hot in there for the sensor.

    Thanks

  2. #2
    Old Timer
    Join Date
    Nov 2006
    Location
    Cleveland/Shaker Heights, Ohio, USA
    Posts
    7,732

    Default Re: Laser sensor inside headlight ?

    Quote Originally Posted by shiggsy
    Hi,
    just bought an LPP for my bike (ZX12). Don't know wether this is stupid or not but I was wondering if locating the sensor inside the headlight was a good or bad idea. Would the sensor still be effective, would the lens be a problem or would it get to hot in there for the sensor.

    Thanks
    ^ Hi there!

    From what little research I've done on these Forums, the "inside another lens" housing is typically not advised, as it is speculated that the additional lens would work to disrupt the outgoing signal.

    Exactly how big of a concern this is, in so far as I know, is an unknown, as no one has truly tested this on a quantitative basis.

  3. #3
    Cheetah Rep
    Join Date
    Feb 2005
    Location
    Phoenix, Arizona
    Posts
    2,567

    Default

    my concern would be the heat build up, especially since most bikes are designed to always have the headlight on.

    as for performance, it has yet to be tested if having a jammer behind the clear headlight glass would cause any issues.

    until it's been tested thoroughly i'd advise against it, since you don't want to wait until you get shot to see if it will work, and how well it will holdup.

    plus. i don't know if the light from the headlight would flood out the light from the jammer, so that the laser gun doesn't see the jamming pulse.

  4. #4
    Newcomer
    Join Date
    Jan 2007
    Location
    UK
    Posts
    35

    Default

    Thanks for replies.
    Ok with the headlight options out, I have a few questions.

    1) How back into the bike can the sensor be located. Does it have to be right at the front ? At the moment the most stealthy position for me is to have the sensor below the headlight a couple of inches but recessed back about 14 inches.

    From the picture here it will be between the gold forks but further back.




    2) Does the sensor have to be mounted horizontally or can it be mounted vertically.

    Thanks

  5. #5
    Advanced Member
    Join Date
    Mar 2005
    Location
    Police State of Ontario
    Posts
    1,967

    Default

    The problem with recessed back is that it may not pick up laser shots from overpass laser and other off axis shooting positions.

    Yes the sensor has to be horizonatlly mounted with attention payed to keeping it level.

    The Laser Park Pro has a head the size of a match box so hopefully you can find a stealthy location. I agree the mounting options on most bikes are limited.

  6. #6
    Newcomer
    Join Date
    Jan 2007
    Location
    UK
    Posts
    35

    Default

    Ok, i decided against that position as well. Coverage wise I think it would have been ok, detection angles typically seem to be fairly narrow, not sure about overpasses but that's not much of a problem on bike. The real problem was mounting it. Mounting on the front mudguard means it will be moving constantly with the suspension so probably not ideal, especially under braking, it risks bashing the sensor into the upper part of the bike as the forks compress. Likewise bashing it into the mudguard means can't mount it on the upper part. That left the radiator guard which sits flush against the rad. The bracket would attach securely to that and bent to keep the sensor away from it, but it does blocks a fair portion of the radiator, even though the bracket is fairly perforated. Cutting away the insde of the bracket could solve that though I guess. As long as having the sensor 14 inches behind the headlight wasn't a problem that would be probably be ok.


    The most effective and obvious place to mount it is in the ram air scoop, problem is it's highly visible there, even recessed back as far as it will go. So for the moment I have placed it to one side of the air scoop slightly under the fairing. It's pretty stealthy there, you have to stand a long way back from the bike to be able to see it or get down on your knees and coverage look pretty good too.

    I have been using a Cheetah Sentinel on the bike for the last 6 months, which is great on the bike because of the wireless audio alerts. The laser alert has only ever been triggered twice but the second time it stopped me going through the speed limit as I was being scanned. For the time being I'll be using the laser alerts from the Sentinel to check my speed before manually turning the LPP off. That'll have to do untill Cheetah bring out a LaserNode for the LPP.

  7. #7
    Advanced Member
    Join Date
    Mar 2005
    Location
    Police State of Ontario
    Posts
    1,967

    Default

    Damn I cant see your pictures can you shrink them a bit. I'm anxioulsy waiting for the Cheetah Viz alert to come out.

    Have you considered using a Ram mount off of the hanldebars?

    You're in the UK?

  8. #8
    Newcomer
    Join Date
    Jan 2007
    Location
    UK
    Posts
    35

    Default

    Hi,
    yes I'm in the UK.

    The pics size should be ok but for some reason it's not always appearing in the thread. If I click on it, it shows up in another window so give that a try.

    The Cheetah crash helmet Viz alert is available in the UK now but I'm not so keen on it, probably just because I have got used to using the audio.

  9. #9
    Advanced Member
    Join Date
    Mar 2005
    Location
    Police State of Ontario
    Posts
    1,967

    Default

    Yup got it and you're right scoops your best bet and looks pretty stealthy to me.

  10. #10
    Professional
    Join Date
    Oct 2006
    Location
    On your six, get outta my way!
    Posts
    1,101

    Default

    I havent bought a jammer yet, but ive been contemplating where to mount it when i do. I was thinking about the ram air duct, as its centrally located. Not sure if i should put it behind the metal screen, or in front of it. As jammers are illegal where i reside, i was leaning toward behind the screen. Since the screen is recessed a bit from the front of the bike, would this still be an effective location for off axis shots? Pic of front of my bike below in my sig.

 

 

Similar Threads

  1. Bright headlight(s) vs. laser
    By oldguy in forum Laser Jammers - General
    Replies: 8
    Last Post: 11-27-2008, 03:57 PM
  2. VEILing mirrored backing inside headlight assembly?
    By bigblue in forum Laser Veil Stealth Coating
    Replies: 1
    Last Post: 08-17-2006, 03:06 AM
  3. Laser Shield Headlight covers
    By jrv2000 in forum Laser Jammers - General
    Replies: 4
    Last Post: 03-07-2006, 04:26 PM
  4. Applying Inside the headlight glass
    By quandary in forum Laser Veil Stealth Coating
    Replies: 6
    Last Post: 02-01-2006, 08:25 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •