Page 1 of 3 123 LastLast
Results 1 to 10 of 24
  1. #1
    Newcomer
    Join Date
    Feb 2007
    Posts
    69

    Default LI and Speed Cheetah DIY

    Hello.

    I would like to buy a LI and connect it to Cheetah. I think you have a LPP with Cheetah and now you've installed a LI.

    I would like to use a LI with a Cheetah wireless. I found the LI wiring diagram in the documentation pdf. With Cheetah and his wireless switch off, I think I need only connect the speaker to the Cheetah interface. The
    LPP and ALG8 have a similar wiring diagram (speaker, on/off, led).

    Do you think is possible to connect easily the LI with Cheetah? http://www.speedcheetah.com/scshop/p...ting_kits.html

  2. #2
    Speed Demon
    Join Date
    Mar 2007
    Location
    Zagreb, Croatia
    Posts
    512

    Default

    difference is that LI have a speeker, and other BUZZER...

    it is a huge difference, actualy "others" provide a + or - on buzzer port when alerting.. :-)

    LI provides a audio signal on 2 blue wires and on CPU speeker, not only a simple + or -..

    On the other hand, what you can use easy is MUTE output on LI... This port will provide - when alerting, if you connect that one to Cheetah port when usualy connect buzzer from "others" it just may work..

    Maybe someone from Cheetah can elaborate on this..

    anyhow if you doo this, there will be no voice or parking monitor alerts, but you will get same warning as from "others"..

    I have NO experience with Cheetah so i can NOT tell you exactly, maybe Racer X or Aly can tell you more..

  3. #3
    Cheetah Rep
    Join Date
    Feb 2005
    Location
    Phoenix, Arizona
    Posts
    2,567

    Default

    it doesn't work at this time. i tried a few things but didn't get it to interface.
    myself and the Cheetah guys will get with Ivan on some things to see what we can do. i'll play with a few more things too.
    i do have a "work around" for those on motorcycles though, so that you can hear the voice alerts through headphones/earpieces.
    i won't be able to play with it until the weekend though, as I'm at SEMA this week.

  4. #4
    Newcomer
    Join Date
    Feb 2007
    Posts
    69

    Default

    [quote="RacerX"]i do have a "work around" for those on motorcycles though, so that you can hear the voice alerts through headphones/earpieces. [quote]

    How works your work around? Withe the AUDIOnode?
    Hope you will find a solution.
    Thanks at all to handle this problem.

  5. #5
    Cheetah Rep
    Join Date
    Feb 2005
    Location
    Phoenix, Arizona
    Posts
    2,567

    Default

    No, once the AUDIOnode works, everything else will automatically work, including the Vizalert and GPS mirror.

    i actually took a simplistic approach, so that i could get audio, until an interface is done to also get the visuals through the Vizalert.
    basically here's what I did:

    First, I use an “extension cord” for the headphones (earpieces), to give me room, plus an easy disconnect point, since the end is near my seat when I get on and off the bike.
    Then, on the LI, if you open the box up, there is a small jumper inside, move it over. This takes the audio from the internal speaker, and puts it in the 2 blue wires. Then I stripped off about an inch on each one. Then I wrapped them around 2 points on the plug end of the extension cord. This gave me sound to the earphones. Once I tested it and they worked, I wrapped them tightly with electrical tap to hold them.
    With an older set I tried to cut the plug on some ear pierces and splice them. But the wires were so small in the earpiece cords it wouldn’t work right and the sound would cut in and out.
    One hint when testing the volume, is to block one of the heads so you get the beeping on startup to test them. this gives you time to ensure you have the audio correct and adjusted.

    It works great. i get the audio of the LI, plus i just put the V1 on the bike, so i get the Laser alerts visually through the Vizalert, should my temp connector come loose.


  6. #6
    Founder of Stealthvation
    Join Date
    Dec 2004
    Location
    Cleveland, Ohio
    Posts
    11,174

    Default

    Quote Originally Posted by RacerX
    No, once the AUDIOnode works, everything else will automatically work, including the Vizalert and GPS mirror.

    i actually took a simplistic approach, so that i could get audio, until an interface is done to also get the visuals through the Vizalert.
    basically here's what I did:

    First, I use an “extension cord” for the headphones (earpieces), to give me room, plus an easy disconnect point, since the end is near my seat when I get on and off the bike.
    Then, on the LI, if you open the box up, there is a small jumper inside, move it over. This takes the audio from the internal speaker, and puts it in the 2 blue wires. Then I stripped off about an inch on each one. Then I wrapped them around 2 points on the plug end of the extension cord. This gave me sound to the earphones. Once I tested it and they worked, I wrapped them tightly with electrical tap to hold them.
    With an older set I tried to cut the plug on some ear pierces and splice them. But the wires were so small in the earpiece cords it wouldn’t work right and the sound would cut in and out.
    One hint when testing the volume, is to block one of the heads so you get the beeping on startup to test them. this gives you time to ensure you have the audio correct and adjusted.

    It works great. i get the audio of the LI, plus i just put the V1 on the bike, so i get the Laser alerts visually through the Vizalert, should my temp connector come loose.


    wow amazing
    RIP Duncan my BELOVED black lab son 8/7/99-3/23/11. I will miss you DEARLY.


    http://www.criminalcustomzshop.com/


    LET THE BIRTH OF MANY TESTING GROUPS HAPPEN!











    You want to know what it is like doing something for the love and passion and not for the mighty dollar then look up GOL!










    buyradardetectors rocks!

  7. #7
    Advanced Member
    Join Date
    Mar 2005
    Location
    Police State of Ontario
    Posts
    1,967

    Default

    Plonkers .... get a move on ... I'm living in a frickin police state

  8. #8
    Newcomer
    Join Date
    Feb 2007
    Posts
    69

    Default

    OK. Hope the Cheetah boys will find a solution soon.

    A bout LI, do you know if we can lengthen the RJ45 cable of a sensor? Whare can we buy the cable?

    Best regards.

  9. #9
    Newcomer
    Join Date
    Feb 2007
    Posts
    69

    Default

    Quote Originally Posted by syrinx
    About LI, do you know if we can lengthen the RJ45 cable of a sensor? Whare can we buy the cable?
    It seems that RJ11.

    Can we use a RJ11 right male to /female to lengthen the sensor's cable? The problem is for rear sensors.

    RJ11 right male to /female like this:
    http://www.cableuniverse.co.uk/catal...products_id=55

  10. #10
    Speed Demon
    Join Date
    Mar 2007
    Location
    Zagreb, Croatia
    Posts
    512

    Default

    as long as it is straight (NOT CROSSOVER) u can use it...

 

 

Similar Threads

  1. M27 Blinder/Speed Cheetah
    By AFineRide in forum Motorcycle Protection
    Replies: 0
    Last Post: 07-22-2012, 06:22 AM
  2. Video: Cheetah C50 Speed Enforced By Aircraft Example
    By rocky2 in forum Other Countermeasures
    Replies: 11
    Last Post: 11-06-2010, 03:22 PM
  3. Not a Speed Cheetah but very interesting
    By Cherokee Driver in forum Other Countermeasures
    Replies: 2
    Last Post: 05-21-2009, 06:47 PM
  4. Speed Cheetah
    By Beatlesfan in forum Valentine One
    Replies: 10
    Last Post: 02-04-2008, 12:30 AM
  5. Cheetah Trinity speed-cam database
    By MetalFlame in forum Other Countermeasures
    Replies: 1
    Last Post: 11-27-2007, 04:37 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •