Page 1 of 3 123 LastLast
Results 1 to 10 of 24
  1. #1

    Default Leveling 9500ci/ZR4/ZR3 front shifter heads...

    Hi everyone,

    Note: This is an expanded duplicate of a post I made on the "other" forum since the topic came up.

    Just before I flew out to SML, I was getting quite nervous regarding installing the 9500ci for the SML test and had a few questions since I have never installed a laser jammer before. Aside from wanting to know how long the various cables were (all are really long), I wanted to know whether or not I should check the level of the shifter heads by placing my small bubble level on the top or bottom surface of the shifter heads. So, I called Escort CS, explained who I was and that I had been approved to go to SML since their engineer couldn't attend SML, and that I had some questions. In truth I was beginning to freak out since I realized that it was going to be entirely up to me to assure that the Bel and Escort products were properly set up for testing -- and me knowing next to nothing about laser jammers!

    Anyway, I got to talk to the engineer who originally was supposed to attend SML yet couldn't for whatever reason. He had been looking forward to attending SML and wasn't very happy that he couldn't attend. Yet he was happy to learn that years ago I used to work at a car stereo shop and had performed many custom car stereo installations and that I seemed to have a fully functional brain in my head.

    Apparently the ZR3 and ZR4 front jammer heads are the same size and use the same external cases. The engineer mentioned that the top and bottom sides of the cases are not parallel but instead have a very slight slope or bevel relative to each other. This is due to the requirement for easy release from the injection molding die. The engineer told me to place my bubble level against the top side of the front shifter cases since the internal emitting LEDs are mounted parallel to the top side of the cases. The top sides of the cases have "THIS SIDE UP" stamped on them.

    The level which I used at SML is a fairly small white pen level which I purchased from my local Ace Hardware store. It is a very accurate level considering its rather cheap price. We use them on our astronomical telescopes to indicate when the telescope is pointing straight up at the zenith. Using these levels, our telescopes are always pointing somewhere within their 20 arc minute (1/3 of a degree) field of view. That is pretty darned good for cheap levels!

    I just got done measuring the front and rear thicknesses of the 9500ci front shifter head cases, and the depth of the shifter heads. I have calculated that there is a 1.7 degree angle difference between the top and the bottom sides of the shifter housings. That is significant. Assuming that you accidentally level your shifter heads by holding a level against the shifter case's bottom surface, then at 500 feet the most intense output of the head will be located at a point 14.8 feet below the installed height of your shifter head. This of course assumes that you are traveling on a flat roadway. At 800 feet (the average laser shot distance) then the most intense portion of your shifter head beams will be pointing nearly 24 feet below the installed height of your shifter heads!

    I am heading out of town tomorrow to see my father one last time before he flies out of town, but when I return I will be taking apart one of the ZR4 shifter heads to confirm that its emitting LEDs are indeed aligned parallel relative to the top surface of the case. Nevertheless, I thought that I would pass this tidbit of information along to all of you who own ZR3, ZR4 or 9500ci systems. Escort's engineer said that leveling using the top side of the shifter cases results in very accurate leveling of the shifters.

    On a side note, for those of you who must hold the Ace level against the bottom side of your shifters, I will slew one of our telescopes exactly 1.7 degrees north of the zenith and then take a photograph to show the exact displacement of the level's bubble. That way you can use the photo as a reference and level your shifters using the bottom side of the shifter housings.

    Additionally, I want to create a spreadsheet which you can download. The spreadsheet will allow you to input the installed height of your front shifter/jammer heads, the average distance of laser shots in your locale, and the normal height of the laser gun (officer standing hand-held or officer seated in patrol car hand-held) in order to calculate the ideal very slight upward tilt for your shifter/jammer heads to assure maximum emitted signal intensity toward the laser gun. Hopefully this info will allow everyone, regardless of what shifter/jammer product they own, to fully tweak their present setup once they have their shifter/jammer heads installed in ideal locations.


  2. #2
    Scratonicity Groupie
    Join Date
    Mar 2005
    Posts
    7,614

    Default

    wow, great info.

  3. #3
    Power User
    Join Date
    May 2007
    Posts
    3,823

    Default

    According to Escorts site the ZR4 front heads are smaller than the ZR3's I am pretty certain I read this.

    Maybe you spoke to the OLd Bag pretending to be the engineer LOL.

    As for taking apart the heads I would not plan on trying to put them back together and using them.

    ZR4:
    Dimensions (inches)
    * Front Laser Transceivers: 3.760 x 1.660 x 0.677


    ZR3:
    Dimensions (inches)
    * Front Laser Transceivers: 4.65 x 1.8 x 0.8

  4. #4
    Old Timer
    Join Date
    Nov 2006
    Location
    Cleveland/Shaker Heights, Ohio, USA
    Posts
    7,732

    Default

    Great info. and tips, MEM-TEK.

    ----

    focal - that's very strange, indeed..... Does anyone here have both the ZR3, and the ZR4, to cross-check and see what set of data is actually correct?

    Speaking of cross-checking, it's a good thing that MEM-TEK did this for us, for the "leveling" issue, with relation to the product's casing. Indeed, this is one of those areas where Escort, I feel, truly has to step-up and make better. In many cases, the advice that their own technical crew passes along to us end-users either conflicts with or is not in-line with what's in the product's manuals and other "officially" published sources of information (this particular issue of the physical dimensions of the front heads' casings is just one such illustration).

    I am most eager, MEM-TEK for the cross-confirmation that, indeed, the ZR4 is an LED-based jammer, too.
    Last edited by TSi+WRX; 07-07-2008 at 10:46 AM.

  5. #5
    Newcomer
    Join Date
    Mar 2007
    Location
    VA / DC / MD / PA
    Posts
    43

    Default

    when using a bubble level to align the heads, doesn't it also matter how level the road is that your car is on at time of install.

    seems like it shouldnt matter because you are aligning in proportion to the car. so can you install parked on an uphill driveway or something... any more tips or advice here?

    also, how do you fine tune and adjust the level of the heads? is there like a screw or something?

    I wish someone local here had a laser jammer on their car and that i could see it in person. it would help alot. All the car meets i been to here, no one has one.

  6. #6
    Professional
    Join Date
    Sep 2007
    Location
    NJ
    Posts
    1,414

    Default

    Here's a thought on a good place to get a level surface for your car to sit on while you check your jammer heads. The concrete slab between the gas pumps at newer stations is going to be very level. Maybe while you fill up you could take advantage of the level surface to check the position of your heads.

  7. #7
    Power User
    Join Date
    May 2007
    Posts
    3,823

    Default

    Quote Originally Posted by Ahujadaddy View Post
    when using a bubble level to align the heads, doesn't it also matter how level the road is that your car is on at time of install.

    seems like it shouldnt matter because you are aligning in proportion to the car. so can you install parked on an uphill driveway or something... any more tips or advice here?

    also, how do you fine tune and adjust the level of the heads? is there like a screw or something?

    I wish someone local here had a laser jammer on their car and that i could see it in person. it would help alot. All the car meets i been to here, no one has one.
    Start off with a flat level road. Many heads differ, some have side screws that you can loosen level then tighten up. If you use tape use little pieces of tape like shims to get it level. If you have them mounted with metal brackets you can bend the bracket slightly.

  8. #8

    Default

    I have looked and ca't find it. if it has been posted already, sorry.
    But how long do you have on the ZR4 to ajust your speed once jamming starts. I think it is call punch thru. I call CM and they claimed 60 seconds.
    I have the blinder and though they claimed 15 seconds. I thought that was a long time, but WOW 60 seconds!?!?!?

    Just trying to make a comparison, if possble.

  9. #9
    Professional
    Join Date
    Sep 2007
    Location
    NJ
    Posts
    1,414

    Default

    Quote Originally Posted by LatinMax View Post
    I have looked and ca't find it. if it has been posted already, sorry.
    But how long do you have on the ZR4 to ajust your speed once jamming starts. I think it is call punch thru. I call CM and they claimed 60 seconds.
    I have the blinder and though they claimed 15 seconds. I thought that was a long time, but WOW 60 seconds!?!?!?

    Just trying to make a comparison, if possble.
    There is no set period of time before a punch through happens. This depends on a variety of factors including, but certainly not limited to, what laser gun the cops are using, how inherently reflective your vehicle is, how far away they're targeting you, etc...

    Basically, if your jammer/detector starts going off, slow down to the posted speed limit as quickly as possible and switch off your jammer.

    Hopefully if this happens your countermeasures have provided enough time for you to slow down before the officer gets a speed reading.

  10. #10

    Default

    Quote Originally Posted by Retaliation View Post
    There is no set period of time before a punch through happens. This depends on a variety of factors including, but certainly not limited to, what laser gun the cops are using, how inherently reflective your vehicle is, how far away they're targeting you, etc...

    Basically, if your jammer/detector starts going off, slow down to the posted speed limit as quickly as possible and switch off your jammer.

    Hopefully if this happens your countermeasures have provided enough time for you to slow down before the officer gets a speed reading.
    I understand all that. But how much time to you have before the jamming stops and they can get a reading off of you. with the Blinder you don't get anymore than 15 seconds. CM claims 60 seconds. I find that hard to beleive.
    Any idea?

 

 

Similar Threads

  1. Leveling the LI heads
    By SpdFreak in forum Laser Interceptor
    Replies: 4
    Last Post: 06-28-2009, 04:28 PM
  2. Replies: 9
    Last Post: 10-03-2008, 01:38 AM
  3. Leveling laser jammer heads...
    By MEM-TEK in forum Laser Jammers - General
    Replies: 10
    Last Post: 05-25-2008, 02:17 PM
  4. Moved My Heads Out + Leveling Question
    By Paul79UF in forum Blinder Laser Jammers
    Replies: 6
    Last Post: 04-17-2006, 08:49 AM
  5. HELP: LEVELING OUT THE HEADS
    By radardan24 in forum Laser Jammers - General
    Replies: 3
    Last Post: 04-15-2006, 10:16 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •