Results 1 to 9 of 9
  1. #1
    Good Citizen
    Join Date
    Jul 2008
    Location
    PNW
    Posts
    78

    Default LI bad connection to sensors

    Installed my LI about 2 months ago. Maybe about a week after installing it I got a "bad connection to sensors" (or something similar to that) at startup. Actually the radio was turned up pretty loud so I didn't really make it out completely but it startled me. I turned the LI off and back on and it gave the normal "welcome" I shrugged it off and forgot all about it until last night. Last night I'm leaving the local supermarket and start up the car and hear "bad connection to sensor". Once again I switch the LI off and back on and "welcome". I've switched the LI on and off maybe a dozen times since then with no problems. Is it normal for the LI to occasionally (every couple months on a daily driver) give a bad connection warning or is this something I need to worry about?

    I probably should have searched before asking but I'm feeling extra lazy today

  2. #2

    Default Re: LI bad connection to sensors

    This is normal and associated with the low voltages being supplied to the LI's Processor in the CPU at start-up!

    Cliff - C55

  3. #3
    Good Citizen
    Join Date
    Jul 2008
    Location
    PNW
    Posts
    78

    Default Re: LI bad connection to sensors

    Thanks for the speedy reply Cliff. Good to know this is a normal "glitch" for lack of a better word.

  4. #4

    Default Re: LI bad connection to sensors

    My pleasure!

    Cliff - C55

  5. #5
    Good Citizen
    Join Date
    Aug 2008
    Posts
    85

    Default Re: LI bad connection to sensors

    I've had that before on my bike when I had my LI, Low beam HID and High beam HID firing at the same time.

    You can resolve that with a dei-528t relay if it becomes a nuisance. That's what I did.

    Now when I turn on the ignition, 5 seconds later the LI will say welcome, 5 seconds after that the HIDS will fire.

    Puts less stress on the electrical system. On a car I doubt there's a problem with stress but on a bike, if you got too much going on at once the battery's voltage drop could stress the battery when it comes time to crank the engine. Now with this setup, once I turn the engine on and the voltage from the stator rises, the draw on the electrical system is stabilized before all the high powered electronics start firing.

  6. #6
    Radar Fanatic
    Join Date
    Oct 2007
    Location
    Ireland
    Posts
    2,748

    Default Re: LI bad connection to sensors

    i have a kill switch for my V1 and i dont switch it or my LPPs on until the car has been running at least a few seconds to save them from the voltage changes that occur during start up.

    same goes for my onboard camera system

  7. #7
    Advanced Member
    Join Date
    Feb 2005
    Location
    Southern MA
    Posts
    10,127

    Default Re: LI bad connection to sensors

    Quote Originally Posted by corkguykev View Post
    i have a kill switch for my V1 and i dont switch it or my LPPs on until the car has been running at least a few seconds to save them from the voltage changes that occur during start up.

    same goes for my onboard camera system
    Well I don't have a kill switch for my detector but I hardly ever turn my jammers on until I am leaving the parking lot or driveway

    Spoiler: show

    Radar Detectors-V1 & BEL v995
    Laser Jammer-Laser Interceptor Quad
    GPS Camera Locator-Cheetah C100
    GPS Nav-Garmin nuvi w/Trapster
    CB Radio-Galaxy DX-949 w/Wilson 500
    Scanner-RS Pro-96

  8. #8
    Power User
    Join Date
    May 2007
    Posts
    3,823

    Default Re: LI bad connection to sensors

    Just in case check to make sure the RJ's did not come loose from the control box.

  9. #9
    Old Timer
    Join Date
    Nov 2006
    Location
    Cleveland/Shaker Heights, Ohio, USA
    Posts
    7,732

    Default Re: LI bad connection to sensors

    BTW, don't forget the obvious! Check your connection.

    Remember, these are road-vehicles, exposed to lots of vibration and impacts.

    That connector really can "just come loose."

 

 

Similar Threads

  1. V1 connection
    By suntzuaow in forum Valentine One
    Replies: 1
    Last Post: 12-03-2012, 03:55 PM
  2. No USB connection
    By vdub.:R in forum Escort
    Replies: 5
    Last Post: 04-01-2012, 07:33 PM
  3. Bad Connection
    By spankyaf in forum Laser Interceptor
    Replies: 0
    Last Post: 01-10-2012, 09:36 AM
  4. connection to sensors 2 or 3 is bad alert during heavy rain
    By mikedotd in forum Laser Interceptor
    Replies: 13
    Last Post: 07-11-2011, 03:25 PM
  5. Bad Connection
    By AcuraTL in forum Laser Interceptor
    Replies: 12
    Last Post: 10-30-2010, 06:38 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •