Page 1 of 3 123 LastLast
Results 1 to 10 of 24
  1. #1
    Newcomer
    Join Date
    Feb 2006
    Location
    TX
    Posts
    42

    Default Veil cracking and chipping away :(

    I need a bit of advice here, thanks in advance.

    I applied veil twice: First time it got pretty cold during the night (about 40 - 45) so it cracked in a few places and then the spots got bigger and bigger. I thought fair enough, I shouldn't have done it in the cold so I took it off (aftershave works very well and the car smells nice afterwards kinda pricey though, used lots of water after) and I waited until the forecast was good. Funny thing is the fog lights were perfectly fine, looked better than the average I've seen in ppl's pics so I left them as they were. You could chip the veil at the edges if you tried hard but they are fine to this day.

    The second time temperature was about 70 - 75 I applied it about 3pm and the car is in covered parking so no direct sunlight. For about 35 hours after that temperature didn't drop under 70 (65 the very lowest maybe) and the car didn't move at all. Then (this was midnight second day) it got fairly cold (bout 50) and it rained. Car was still under the cover so didn't rain on it. Sure enough the veil was cracked again, this time in a slightly different way, the spots are a lot more round, first time they were like cracks in glass.

    Am I doing anything wrong? I applied the Veil with the brush only, definitely not too much of it and stopped as early as possible to stop smudging when it dries. Cleaned the lights loads before applying. Horizontal motion, top to bottom, the whole 9 yards. Only thing was it was a bit windy (10 - 15mph) and a few specks of dust got trapped in the veil but I really don't think this is the probpem. In case it matters the car is a 2000 Chrysler LHS, a lot like the Concorde.

    Any tips are welcome since the car looks really bad now. Thanks.

  2. #2
    Founder of Stealthvation
    Join Date
    Dec 2004
    Location
    Cleveland, Ohio
    Posts
    11,174

    Default Re: Veil cracking and chipping away :(

    Quote Originally Posted by n1tr08urner
    I need a bit of advice here, thanks in advance.

    I applied veil twice: First time it got pretty cold during the night (about 40 - 45) so it cracked in a few places and then the spots got bigger and bigger. I thought fair enough, I shouldn't have done it in the cold so I took it off (aftershave works very well and the car smells nice afterwards kinda pricey though, used lots of water after) and I waited until the forecast was good. Funny thing is the fog lights were perfectly fine, looked better than the average I've seen in ppl's pics so I left them as they were. You could chip the veil at the edges if you tried hard but they are fine to this day.

    The second time temperature was about 70 - 75 I applied it about 3pm and the car is in covered parking so no direct sunlight. For about 35 hours after that temperature didn't drop under 70 (65 the very lowest maybe) and the car didn't move at all. Then (this was midnight second day) it got fairly cold (bout 50) and it rained. Car was still under the cover so didn't rain on it. Sure enough the veil was cracked again, this time in a slightly different way, the spots are a lot more round, first time they were like cracks in glass.

    Am I doing anything wrong? I applied the Veil with the brush only, definitely not too much of it and stopped as early as possible to stop smudging when it dries. Cleaned the lights loads before applying. Horizontal motion, top to bottom, the whole 9 yards. Only thing was it was a bit windy (10 - 15mph) and a few specks of dust got trapped in the veil but I really don't think this is the probpem. In case it matters the car is a 2000 Chrysler LHS, a lot like the Concorde.

    Any tips are welcome since the car looks really bad now. Thanks.
    Dont feel bad only a couple have mastered the application of Veil one being Sethy and the other the famous Bob. I have been trying to get it down for a year now :cry:
    RIP Duncan my BELOVED black lab son 8/7/99-3/23/11. I will miss you DEARLY.


    http://www.criminalcustomzshop.com/


    LET THE BIRTH OF MANY TESTING GROUPS HAPPEN!











    You want to know what it is like doing something for the love and passion and not for the mighty dollar then look up GOL!










    buyradardetectors rocks!

  3. #3
    Newcomer
    Join Date
    Feb 2006
    Location
    TX
    Posts
    42

    Default

    Lol, OK I guess I do feel a little better but I'd still like to get it right cause right now it has a hundred little holes in it which can't help performance. And I'm pretty sure the first wash will make it a lot worse.

  4. #4
    Old Timer
    Join Date
    Jan 2005
    Location
    Ohio
    Posts
    5,183

    Default

    A good technique, is the hairdryer. There is a catch though...

    Apply the veil, and let it sit to the point where it is not wet anymore. Take a hair dryer, put it on something and point it at your headlight. leave it there for anhour or so, move on to the next one. You can also leave your brights on, the hotter the veil is when it is dry, the faster the bonding process.

    Do NOT put the hairdryer on the VEiL when it is still wet. I say this because I made this mistake a few times. What happens, is the hairdryer sucks in dirt and crap from the air, and will spit it onto the VEiL, and you will have spots, and chunks of stuff in your VEiL after it is dried.

    Personally, I had never had chipping problems with VEiL, until the last time at the GOL test I applied it. It rained and chipped away. I applied some of happya$$'s and drove home with that, which it later chipped away due to the freezing temps outside. I gave it one last chance, with the hairdryer technique for 30 minutes, and the chipping was very very small, but of coarse grew bigger, which is why I am recommending an hour on each headlight.

    Veil Guy had an idea, which I tried to my car, is put plastic wrap around the light, so moisture will be blocked out. This trick works, it has rianed twice with my car outside, and my current chipped VEiL hasnt gotten an "chippier" You cant really notice the plastic on the lights as well, let me show you a pic of it on my car...



    The plastic is temporary of course, until it gets warmer outside so the VEiL can finally bond.

    Wind will def affect how the VEiL drys, and will always throw some dirt and unwanted crap into your VEiL coat. I would recommend applying it inside a garage.

    Hope this helps. Keep us updated, good luck!

  5. #5
    Newcomer
    Join Date
    Feb 2006
    Location
    TX
    Posts
    42

    Default

    Thanks for the reply,

    I guess my best bet is waiting for a day that is as hot as possible, maybe in a couple of weeks. The hairdryer isn't really an option since I don't have an electric lead long enough to reach the car and for that matter I don't really have a hairdryer at the moment (away at university and not much hair to dry...) The plastic might be an idea but after I get rid of this coat and apply a new one. It's weird though because it wasn't really that cold, over 65 for at least 30 hours, no rain, no driving. Thanks again for the tips and any other ideas are welcome.

  6. #6
    Power User
    Join Date
    Apr 2005
    Location
    Evergreen State
    Posts
    3,884

    Default

    Be sure to wipe your head lamps off with alcohol before applying the veil, you want to give it a nice clean surface to adhere too!

  7. #7
    Cheetah Rep
    Join Date
    Feb 2005
    Location
    Phoenix, Arizona
    Posts
    2,567

    Default

    Yeah, i think we'll change Sethy's name from "Tape Master" to "Veil Master". he's got it down.

    i had a similar problem last year and it was due to the cold.

    i waited till a sunny day and used a dryer to warm up the headlights then applied the Veil.
    Also i think that first time was a bit thick, because those were the spots that cracked/chipped.

    after setting, i did the dryer technique for a while, then let it sit facing the sun the rest of the day.
    that night i threw a blanket over the front and the next day it was still looking good.
    let it sit in the sun again and it was fine.

    shoot for two days of good weather or two days of covered parking and you should be set.

  8. #8
    Newcomer
    Join Date
    Feb 2006
    Location
    Weston, FL
    Posts
    32

    Default

    I thought it was pretty easy to apply VEIL.

    I can't imagine all of you aren't removing the lights when painting on something that could stain your paint. I love my car too much to risk that.

    I removed both my headlights and fog lights from the car to apply the VEIL.

    I cleaned them completely with water, then alcohol.

    After I painted on the VEIL, I kept them inside over night and almost all of the next day balanced upright to dry.

    I couldn't be happier with the way they turned out.


  9. #9
    Professional
    Join Date
    Sep 2005
    Location
    Wisconsin
    Posts
    958

    Default

    i had this same problem, but it was just too cold in my case. i really cant wait for it to warm up so i can reapply

  10. #10
    Newcomer
    Join Date
    Feb 2006
    Location
    TX
    Posts
    42

    Default

    It looks easy enough to apply and it looks pretty good once I'm done but 2 days later it's all spots cause it cracked and chipped away. and the strange thing is I did the lasershield and then the fog lamps and they are both fine. Then I did the lights twice and both times they went really bad.

    Removing the headlights isn't really an option because you pretty much need to take half the car apart, I'm actually praying I never need to replace a bulb. I had a civic before and it was a 5 min job.

    Applying it too thick seems unlikely to be the problem since I applied it as thin as possible. Any less of it and it would have smeared really bad cause it dries fast.

    I guess waiting for some warm weather is the ticket but what exactly is warm? I mean last time it never went under 65 for a day and a half. Is humidity a big problem, should I aim for a day that's as dry as possible? By humidity I don't mean rain, that's obviously a bad idea.

 

 

Similar Threads

  1. Did Veil cause cracking?
    By dcdave78 in forum Laser Veil Stealth Coating
    Replies: 40
    Last Post: 01-18-2010, 03:13 PM
  2. My Veil Is chipping
    By justinkk2005 in forum Laser Veil Stealth Coating
    Replies: 14
    Last Post: 09-11-2007, 11:31 PM
  3. Veil and chipping off while washing/driving
    By alpinestars_2002795 in forum Laser Veil Stealth Coating
    Replies: 7
    Last Post: 08-27-2006, 08:57 PM
  4. Veil chipping suprisingly fast, kinda disappointed
    By TeamQuack in forum Laser Veil Stealth Coating
    Replies: 6
    Last Post: 05-02-2006, 05:28 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •