View Full Version : Veil cracking and chipping away :(
n1tr08urner
02-19-2006, 12:32 AM
I need a bit of advice here, thanks in advance.
I applied veil twice: First time it got pretty cold during the night (about 40 - 45) so it cracked in a few places and then the spots got bigger and bigger. I thought fair enough, I shouldn't have done it in the cold so I took it off (aftershave works very well and the car smells nice afterwards :) kinda pricey though, used lots of water after) and I waited until the forecast was good. Funny thing is the fog lights were perfectly fine, looked better than the average I've seen in ppl's pics so I left them as they were. You could chip the veil at the edges if you tried hard but they are fine to this day.
The second time temperature was about 70 - 75 I applied it about 3pm and the car is in covered parking so no direct sunlight. For about 35 hours after that temperature didn't drop under 70 (65 the very lowest maybe) and the car didn't move at all. Then (this was midnight second day) it got fairly cold (bout 50) and it rained. Car was still under the cover so didn't rain on it. Sure enough the veil was cracked again, this time in a slightly different way, the spots are a lot more round, first time they were like cracks in glass.
Am I doing anything wrong? I applied the Veil with the brush only, definitely not too much of it and stopped as early as possible to stop smudging when it dries. Cleaned the lights loads before applying. Horizontal motion, top to bottom, the whole 9 yards. Only thing was it was a bit windy (10 - 15mph) and a few specks of dust got trapped in the veil but I really don't think this is the probpem. In case it matters the car is a 2000 Chrysler LHS, a lot like the Concorde.
Any tips are welcome since the car looks really bad now. Thanks.
happya$$
02-19-2006, 06:34 AM
I need a bit of advice here, thanks in advance.
I applied veil twice: First time it got pretty cold during the night (about 40 - 45) so it cracked in a few places and then the spots got bigger and bigger. I thought fair enough, I shouldn't have done it in the cold so I took it off (aftershave works very well and the car smells nice afterwards :) kinda pricey though, used lots of water after) and I waited until the forecast was good. Funny thing is the fog lights were perfectly fine, looked better than the average I've seen in ppl's pics so I left them as they were. You could chip the veil at the edges if you tried hard but they are fine to this day.
The second time temperature was about 70 - 75 I applied it about 3pm and the car is in covered parking so no direct sunlight. For about 35 hours after that temperature didn't drop under 70 (65 the very lowest maybe) and the car didn't move at all. Then (this was midnight second day) it got fairly cold (bout 50) and it rained. Car was still under the cover so didn't rain on it. Sure enough the veil was cracked again, this time in a slightly different way, the spots are a lot more round, first time they were like cracks in glass.
Am I doing anything wrong? I applied the Veil with the brush only, definitely not too much of it and stopped as early as possible to stop smudging when it dries. Cleaned the lights loads before applying. Horizontal motion, top to bottom, the whole 9 yards. Only thing was it was a bit windy (10 - 15mph) and a few specks of dust got trapped in the veil but I really don't think this is the probpem. In case it matters the car is a 2000 Chrysler LHS, a lot like the Concorde.
Any tips are welcome since the car looks really bad now. Thanks.
Dont feel bad only a couple have mastered the application of Veil one being Sethy and the other the famous Bob. I have been trying to get it down for a year now :cry:
n1tr08urner
02-19-2006, 07:45 AM
Lol, OK I guess I do feel a little better but I'd still like to get it right cause right now it has a hundred little holes in it which can't help performance. And I'm pretty sure the first wash will make it a lot worse.
sethy
02-19-2006, 09:32 AM
A good technique, is the hairdryer. There is a catch though...
Apply the veil, and let it sit to the point where it is not wet anymore. Take a hair dryer, put it on something and point it at your headlight. leave it there for anhour or so, move on to the next one. You can also leave your brights on, the hotter the veil is when it is dry, the faster the bonding process.
Do NOT put the hairdryer on the VEiL when it is still wet. I say this because I made this mistake a few times. What happens, is the hairdryer sucks in dirt and crap from the air, and will spit it onto the VEiL, and you will have spots, and chunks of stuff in your VEiL after it is dried.
Personally, I had never had chipping problems with VEiL, until the last time at the GOL test I applied it. It rained and chipped away. I applied some of happya$$'s and drove home with that, which it later chipped away due to the freezing temps outside. I gave it one last chance, with the hairdryer technique for 30 minutes, and the chipping was very very small, but of coarse grew bigger, which is why I am recommending an hour on each headlight.
Veil Guy had an idea, which I tried to my car, is put plastic wrap around the light, so moisture will be blocked out. This trick works, it has rianed twice with my car outside, and my current chipped VEiL hasnt gotten an "chippier" You cant really notice the plastic on the lights as well, let me show you a pic of it on my car...
http://img108.imageshack.us/img108/9940/cimg0123small2tm.jpg
The plastic is temporary of course, until it gets warmer outside so the VEiL can finally bond.
Wind will def affect how the VEiL drys, and will always throw some dirt and unwanted crap into your VEiL coat. I would recommend applying it inside a garage.
Hope this helps. Keep us updated, good luck!
n1tr08urner
02-19-2006, 09:39 AM
Thanks for the reply,
I guess my best bet is waiting for a day that is as hot as possible, maybe in a couple of weeks. The hairdryer isn't really an option since I don't have an electric lead long enough to reach the car and for that matter I don't really have a hairdryer at the moment (away at university and not much hair to dry...) The plastic might be an idea but after I get rid of this coat and apply a new one. It's weird though because it wasn't really that cold, over 65 for at least 30 hours, no rain, no driving. Thanks again for the tips and any other ideas are welcome.
holein1
02-20-2006, 09:57 AM
Be sure to wipe your head lamps off with alcohol before applying the veil, you want to give it a nice clean surface to adhere too!
RacerX
02-20-2006, 11:05 AM
Yeah, i think we'll change Sethy's name from "Tape Master" to "Veil Master". he's got it down.
i had a similar problem last year and it was due to the cold.
i waited till a sunny day and used a dryer to warm up the headlights then applied the Veil.
Also i think that first time was a bit thick, because those were the spots that cracked/chipped.
after setting, i did the dryer technique for a while, then let it sit facing the sun the rest of the day.
that night i threw a blanket over the front and the next day it was still looking good.
let it sit in the sun again and it was fine.
shoot for two days of good weather or two days of covered parking and you should be set.
Paul79UF
02-21-2006, 04:53 PM
I thought it was pretty easy to apply VEIL.
I can't imagine all of you aren't removing the lights when painting on something that could stain your paint. I love my car too much to risk that.
I removed both my headlights and fog lights from the car to apply the VEIL.
I cleaned them completely with water, then alcohol.
After I painted on the VEIL, I kept them inside over night and almost all of the next day balanced upright to dry.
I couldn't be happier with the way they turned out.
http://www.partypursuit.com/temp/gtp/gtp6.jpg
Mackid343
02-21-2006, 05:12 PM
i had this same problem, but it was just too cold in my case. i really cant wait for it to warm up so i can reapply
n1tr08urner
02-22-2006, 04:02 AM
It looks easy enough to apply and it looks pretty good once I'm done but 2 days later it's all spots cause it cracked and chipped away. and the strange thing is I did the lasershield and then the fog lamps and they are both fine. Then I did the lights twice and both times they went really bad.
Removing the headlights isn't really an option because you pretty much need to take half the car apart, I'm actually praying I never need to replace a bulb. I had a civic before and it was a 5 min job.
Applying it too thick seems unlikely to be the problem since I applied it as thin as possible. Any less of it and it would have smeared really bad cause it dries fast.
I guess waiting for some warm weather is the ticket but what exactly is warm? I mean last time it never went under 65 for a day and a half. Is humidity a big problem, should I aim for a day that's as dry as possible? By humidity I don't mean rain, that's obviously a bad idea.
n1tr08urner
02-22-2006, 04:05 AM
Oh yeah and when I applied it I used tape to mask the rest of the car which is pretty fast (2 min) and unlike paper or something like that makes sure none of it leaves the headlights and goes on the paint.
sethy
02-22-2006, 12:53 PM
It looks easy enough to apply and it looks pretty good once I'm done but 2 days later it's all spots cause it cracked and chipped away. and the strange thing is I did the lasershield and then the fog lamps and they are both fine. Then I did the lights twice and both times they went really bad.
Removing the headlights isn't really an option because you pretty much need to take half the car apart, I'm actually praying I never need to replace a bulb. I had a civic before and it was a 5 min job.
Applying it too thick seems unlikely to be the problem since I applied it as thin as possible. Any less of it and it would have smeared really bad cause it dries fast.
I guess waiting for some warm weather is the ticket but what exactly is warm? I mean last time it never went under 65 for a day and a half. Is humidity a big problem, should I aim for a day that's as dry as possible? By humidity I don't mean rain, that's obviously a bad idea.
Did you try the method I suggested above? w/ the hair dryer?
n1tr08urner
02-22-2006, 02:50 PM
No, like I said I don't have either an electric lead that's long enough to reach the car or a hairdryer and I can't really be bothered to buy them just for this. So then the problem is the veil is drying too slowly just left outside? Cause as far as i know paint in general cracks more if it dries quicker. I mean the instructions say don't apply in direct sunlight and avoid the high temperatures at noon, do it evening or morning. Should the hairdryer have the heat switched off?
n1tr08urner
02-26-2006, 12:36 AM
Ok, forecast for next 4 days, sunday to wednesday is LO/HI: 44/65 55/70 58/76 60/79. Mostly cloudy. Only 20% chance of rain thursday. Hardly any wind. If I put it on Monday morning (55/70) then according to the instructions I should be ok, at least 3 dry days with lows over 50. Problem is this is more or less what the weather was like last time and results were less than perfect. It did rain after less than 2 days but car is under cover but not garaged. Any ideas? Should I go for it? If I don't do it now might as well wait another month till weather is properly warm.
Btw windex works surprisingly well at taking the veil off. On one hand its good cause I don't have to waste any more aftershave :) . On the other hand it's a bit worrying since that stuff isn't exactly radioactive waste, I didn't expect it to be strong enough, a car wash might use similar stuff.
n1tr08urner
02-27-2006, 10:10 AM
K, I did it... No rain forecast for like 4-5 days, probably more, no temps under 55. A little fog and clouds but then again its always humid round here and it'll only get worse as it gets warmer. Hope it sticks this time. Stand by for results in bout 3 days.
brick
02-27-2006, 11:05 AM
Don't forget about dew! You might want to cover the headlights at night in order to prevent condensation when the temps drop. A small towel draped over each one ought to do the trick.
n1tr08urner
02-27-2006, 11:35 AM
That's actually a really good point, thanks, will do. They should be dry enough by tonight to be covered with something.
n1tr08urner
02-27-2006, 03:16 PM
About the towels, Sethy suggested covering with plastic. The plastic seems better at keeping moisture away but also at keeping it in should it get there. The towels would let it breathe more but they aren't exactly water proof. Any ideas as to which would be better. They might both work just as well...
So far things look very promising, no smears no spots or cracks. Looong brush strokes from one end to the other work great. A couple of tiny flies are trapped in there for what's gonna be a very long ride for them...
brick
02-27-2006, 04:51 PM
Plastic would be OK but it isn't necessary to "seal" the lights. Remembering back to my amateur astronomy days, the important part of keeping condensation off of a telescope lense was to block it's view of the sky. Surfaces get cold mainly because they are open to the sky and space, which is very cold from a radiation standpoint. That causes these surfaces, like your headlights, to chill down to a temperature below the dew point and get wet. All it took to keep a lense dry was to use a big, tubular "dew shield" to reduce the field of view to only the bit of sky we were interested in.
Long story short, the porous towel is probably best because it will allow the Veil to breathe while still keeping the lense from cooling down too much. I worry about plastic because if moisture did get behind it, it would have no way out.
n1tr08urner
02-27-2006, 05:25 PM
Hmm actually that's a good point, takes a pretty big volume of air to make much moisture so if its relatively isolated from the air it doesn't need to be airtight and the towels will also keep it warmer. I'm already getting looks from the neighbours for repeatedly covering my headlights in weird stuff, this won't make it better :D But what do they know... 8)
brick
02-27-2006, 05:51 PM
I know how you feel. I live in an apartment comples, and a pretty sketchy one at that. Every time I go out there to remove/apply Veil, make a change to how the V1 is set up, or whatever else I get LOTs of raised eyebrows.
n1tr08urner
02-27-2006, 08:54 PM
Yeah, same here.
Found a couple of little towels, bright red, forget chrome, this is the next big thing in pimping your ride! I'll b rich! :idea:
n1tr08urner
03-01-2006, 04:22 PM
In case anyone cares the Veil stuck great, this is the third day and temps are over 80 so quite promising. No more towels tonight although they announced fog, if it's still there tomorrow then it stuck.
Unfortunately my car is more of a granny-mobil (a pretty fast one though) than a street racer and being white as well Veil doesn't do it many favours in the looks department. They should come up with more "flavours" of it for different types of cars.
Mackid343
03-01-2006, 06:24 PM
good to hear its sticking so far. the fog will definately show if it worked or not. i personally think veil gives a darker more mean look to the headlights :)
granny-mobil's can be stealth too! :D