Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 22
  1. #11
    Yoda of Radar
    Join Date
    Dec 2004
    Location
    In front of my computer
    Posts
    10,773

    Default

    Quote Originally Posted by ronsc1985
    Pretty much all electronic anything transmits the frequencies it is running at. You can minimize this to some extent by running at lower power i.e. current levels, but without being shielded they all emit and can be detected. The case of the STI is probably the primary shielding method being used.
    I don't think so, there is a big wide hole on either side and a small grille on the bottom. And a small hole again on top.

    It's pretty clear the primary shielding method is the dual antennae horns...

  2. #12
    Experienced
    Join Date
    Mar 2007
    Location
    TX
    Posts
    243

    Default

    if the holes are smaller than the wavelength of the leaking RF energy then the signal can't get through the hole

  3. #13
    Radar Fanatic
    Join Date
    Apr 2005
    Location
    Indianapolis, IN
    Posts
    2,816

    Default

    The magnesium case may play at least a small part in the shielding, but that alone cannot make it totally stealth. I doubt that BEL went to the magnesium case for aesthetics alone, unless they are copying VR.

    GTO_04

  4. #14
    Experienced
    Join Date
    Mar 2007
    Location
    TX
    Posts
    243

    Default

    I'm pretty sure the full case plays a much bigger part than you give it credit for.

    Electronics design can only do so much to control RF leakage; physicaly blocking the signal does the most good and covers whats left.

    without seeing the insides of an sti i can't really say but if you take the plasic outer case off you can get by with it but i'm willing to bet a good amount of money that if you crack open the magnesium case exposing all the electronics an RDD should sniff it out no problem.

  5. #15
    Yoda of Radar
    Join Date
    Dec 2004
    Location
    In front of my computer
    Posts
    10,773

    Default

    Yes but how can it really block anything with the hole? I mean some very low frequency signals can't pass but I don't think Spectre goes that low :wink:

  6. #16
    Lead Foot
    Join Date
    Jan 2006
    Location
    Ohio
    Posts
    444

    Default

    Quote Originally Posted by SmaartAasSaabr
    Yes but how can it really block anything with the hole? I mean some very low frequency signals can't pass but I don't think Spectre goes that low :wink:
    :wink: There you go, you guys are starting to get it. The case is for esthetics. High price, metal case, Spectre proof, powered speaker and marketed at Truck Stops. Target audience? C'mon anyone. Truckers would appreciate the ruggedness of the metal case, yes?
    The simple fact that the case has HUGE RF holes in the front, the rear and both sides should tell everyone that the case isn't what makes this unit Non-detectable.

  7. #17
    Experienced
    Join Date
    Mar 2007
    Location
    TX
    Posts
    243

    Default

    Quote Originally Posted by SmaartAasSaabr
    Yes but how can it really block anything with the hole? I mean some very low frequency signals can't pass but I don't think Spectre goes that low :wink:

    Does anyone in this thread really understand radio frequencies? wavelenths vs. shilelding etc?

    i'm starting to think no they dont.

    The 1:1 ratio wavelength of 24.125ghz is 1/2" if you have a hole in an all metal enclousure thats less than that any radio frequencies are going to have a hard time getting out of that; same with the mesh; if the holes in the mesh are smaller than the wavelenth that rf energy is going to bounce right off and not go through. 24ghz is high for an internal oscillator or heterodyne signal so the wavelengths will only get LONGER as signal frequency decreases.

    If you don't believe me go find some sheet metal; weld a box up w/ a lid; and cut a 4" hole and put a radio inside it. Keep the antenna in it and see how many stations you can pick up. The same goes for metal buildings; that is why you get **** for reception in them and elevators (which are big metal boxes).

    why do you think old C-band satellite dishes are made of a wire mesh material. Well not all but a lot of them.


    Simply put the metal case that surrounds the electronics inside an sti IS THE MOST IMPORTANT SHIELD for rf leakage. Am I the only one that understands this?



    /edit: someone really needs to post pictures of the guts of the sti

  8. #18
    Good Citizen
    Join Date
    Feb 2006
    Location
    Virginia
    Posts
    199

    Default

    Quote Originally Posted by Computerjlt


    Simply put the metal case that surrounds the electronics inside an sti IS THE MOST IMPORTANT SHIELD for rf leakage. Am I the only one that understands this?

    No.

  9. #19
    Advanced Member
    Join Date
    Dec 2004
    Location
    Michigan
    Posts
    7,509

    Default

    By far most of the leakage is transmitted back out the antenna, a common scenario is the first LO feeding back through the first mixer.

    Probably the main thing that makes the STi stealth is the use of LNA's (Low Noise Amplifiers) in the front end. The LNAs provide good reverse isolation, letting radar in, but preventing oscillator frequencies etc from leaking out.

    Before the STi's release, the only detector that used these LNA's was the V1, which explains why the older V1s did magnitudes better than other detectors against the Spectre (before the STi, of course). This might also be one reason why the STi is now the V1's closest competitor.

    My guess is that whatever leakage the LNAs don't take care of is probably taken care of using RF filters (microstrip, waveguide, etc)...

  10. #20

    Default

    *****

 

 

Similar Threads

  1. POP question and Threat mode question
    By yahtzee in forum Beltronics
    Replies: 15
    Last Post: 08-19-2007, 08:03 PM
  2. dumb question????..now with 2nd, follow up question!!!
    By the-ROOSTER- in forum Radar Detectors - General
    Replies: 20
    Last Post: 02-18-2007, 12:08 PM
  3. Replies: 4
    Last Post: 01-31-2007, 10:29 PM
  4. Shielding : % due to Casing ?
    By 411 in forum Radar Detectors - General
    Replies: 2
    Last Post: 02-09-2006, 11:08 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •