Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: STI Power on

  1. #1
    Newcomer
    Join Date
    Oct 2006
    Location
    Northern Ontario
    Posts
    40

    Default STI Power on

    I have my STI hardwired to a toggle switch that is then controlled by my ignition (when I turn the key off my sti turns off). Now when I get in my vehicle and turn the key to the run position the Sti turns on but when i start the car it turns back off for a second while the motor starts and then turns back on the the engine is running. Sometimes the startup sequence on the Sti doesn't even finish before it is turned off and then on again. Is this rapid off and on bad for my detector? Should I only turn it on after my vehicle starts and is it okay to just cut the power to the detector or should I turn it off first?

  2. #2
    Yoda of Radar
    Join Date
    Nov 2005
    Location
    NY
    Posts
    11,015

    Default Re: STI Power on

    Quote Originally Posted by silverado_76
    I have my STI hardwired to a toggle switch that is then controlled by my ignition (when I turn the key off my sti turns off). Now when I get in my vehicle and turn the key to the run position the Sti turns on but when i start the car it turns back off for a second while the motor starts and then turns back on the the engine is running. Sometimes the startup sequence on the Sti doesn't even finish before it is turned off and then on again. Is this rapid off and on bad for my detector? Should I only turn it on after my vehicle starts and is it okay to just cut the power to the detector or should I turn it off first?
    I always turn my detector on after the car is already started, and I turn it off before I turn the car (keys) all the way to the off position. I suggest you change your set-up, but thats always been my opinion on this subject.

  3. #3
    Radar Fanatic
    Join Date
    Jan 2008
    Location
    Nebraska
    Posts
    2,216

    Default

    Mine displays the low volt message when power cycling with the ignition which is why I turn the RD on after starting the car and shut it off prior to turning the car off. There have been a few reports here of settings getting screwed up while power cycling with the ignition.

  4. #4
    Radar Fanatic
    Join Date
    Sep 2007
    Location
    CANADA
    Posts
    2,529

    Default Re: STI Power on

    Quote Originally Posted by AirMoore
    Quote Originally Posted by silverado_76
    I have my STI hardwired to a toggle switch that is then controlled by my ignition (when I turn the key off my sti turns off). Now when I get in my vehicle and turn the key to the run position the Sti turns on but when i start the car it turns back off for a second while the motor starts and then turns back on the the engine is running. Sometimes the startup sequence on the Sti doesn't even finish before it is turned off and then on again. Is this rapid off and on bad for my detector? Should I only turn it on after my vehicle starts and is it okay to just cut the power to the detector or should I turn it off first?
    I always turn my detector on after the car is already started, and I turn it off before I turn the car (keys) all the way to the off position. I suggest you change your set-up, but thats always been my opinion on this subject.
    Exactly how I've been doing all the time, so manually turning it off before turning the engine off and then after the engine is back on I just (manually again) turn it back on, very rarely when I forget to turn it off and I turned the engine off, when turning the engine back on the STI will do that quick sequence related in Silverado's first post, nothing wrong in my opinion but I personally prefer to start the engine with the STI already off and then turn it on manually...

  5. #5
    Newcomer
    Join Date
    Oct 2006
    Location
    Northern Ontario
    Posts
    40

    Default

    Ok so wait untill engine is started. But is it ok to have an external power switch to turn it on and off or should I use the power button on the STI?

  6. #6

    Default

    Quote Originally Posted by silverado_76
    Ok so wait untill engine is started. But is it ok to have an external power switch to turn it on and off or should I use the power button on the STI?
    The external power switch is fine and will cause no problems unless the external power switch itself ever becomes flaky which is unlikely.

    There are three reasons why I always power on my RDs after I have started my car and made sure that my car engine is idling smoothly:

    1. With Belscort products, every once in a blue moon the firmware settings can get hosed while the RD is powering up while cranking your car. This once in a blue moon type of condition is generally obvious in that the normal RD power up sequence will not seem to be normal. If this occurs, then some possible results may be no audio, or no alerts whatsoever to radar. A firmware reset will solve this problem since the default settings are reloaded from the non-volatile programming after a reset.

    2. A sudden voltage spike from other car electronics, while starting your car, can potentially blow an internal capacitor within any RD.

    3. I always make sure that my car is idling smoothly before turning on my RD. Why? Because a smooth idle translates to smooth voltage output from my car's alternator. Steady voltage is important for Belscort RDs while they perform their internal self calibration process which precisely adjusts the voltage for the circuitry which controls the RD's local ocsillators. Thus, self calibration error messages are prevented and you are assured that your RD 10 seconds after power up and the completion of its self calibration process will be operating at maximum sensitivity given its current ambient operating temperature conditions.

  7. #7
    Radar Fanatic
    Join Date
    Sep 2007
    Location
    CANADA
    Posts
    2,529

    Default

    Quote Originally Posted by silverado_76
    Ok so wait untill engine is started.
    Yes, also don't forget to always turn it off BEFORE you turn off the engine :wink:


    Quote Originally Posted by silverado_76
    But is it ok to have an external power switch to turn it on and off or should I use the power button on the STI?
    Do you REALLY need a freaking external switch when you can super easily do it by hand, on and off... use the power button to turn it off and on, ok?

  8. #8
    Newcomer
    Join Date
    Oct 2006
    Location
    Northern Ontario
    Posts
    40

    Default

    Quote Originally Posted by RW'07
    Quote Originally Posted by silverado_76
    Ok so wait untill engine is started.
    Yes, also don't forget to always turn it off BEFORE you turn off the engine :wink:


    Quote Originally Posted by silverado_76
    But is it ok to have an external power switch to turn it on and off or should I use the power button on the STI?
    Do you REALLY need a freaking external switch when you can super easily do it by hand, on and off... use the power button to turn it off and on, ok?
    I'm not a lazy ass I just don't want the OPP to see me reaching up to turn off and on my RD so I mounted a switch below my steering wheel.

  9. #9
    Professional
    Join Date
    Jun 2005
    Location
    The Netherworld of the Force
    Posts
    1,290

    Default

    Quote Originally Posted by silverado_76
    Quote Originally Posted by RW'07
    Quote Originally Posted by silverado_76
    Ok so wait untill engine is started.
    Yes, also don't forget to always turn it off BEFORE you turn off the engine :wink:


    Quote Originally Posted by silverado_76
    But is it ok to have an external power switch to turn it on and off or should I use the power button on the STI?
    Do you REALLY need a freaking external switch when you can super easily do it by hand, on and off... use the power button to turn it off and on, ok?
    I'm not a lazy ass I just don't want the OPP to see me reaching up to turn off and on my RD so I mounted a switch below my steering wheel.
    I had installed a kill switch when I had my X50 Blue, but decided to keep it when I bought my STi. I used it to cut power at the border during my recent trip to Toronto, and turned it back on right after I cleared Customs (just to be on the safe side). I usually leave the power ON when I turn the car on and off, and have not yet had any problems with my STi.

    I personally wouldn't worry about it. If you have the STi and you're driving in Ontario, YOU have the advantage. Make sure you hardwire it on your visor, and cover it with a visor holder. PM RW'07 for some tips - I'm sure he can give you more advice.

  10. #10
    Radar Fanatic
    Join Date
    Sep 2007
    Location
    CANADA
    Posts
    2,529

    Default

    Quote Originally Posted by silverado_76
    I'm not a lazy ass I just don't want the OPP to see me reaching up to turn off and on my RD so I mounted a switch below my steering wheel.
    Free country, of course you're free to install any switch you think it's gonna make you happy but really, why do you have to turn it off anytime you see a cop, local or OPP, around you? :shock: I never do it cause I see no reason for doing it, important is for them NOT to see it, nobody is gonna hear a freaking beep coming out of your car!

 

 

Similar Threads

  1. Replies: 2
    Last Post: 12-14-2011, 03:42 PM
  2. LI CPU Box Power
    By saxman717 in forum Laser Interceptor
    Replies: 9
    Last Post: 08-13-2010, 05:07 PM
  3. quick question m27 power wire constant or switched power?
    By autobel in forum Blinder Laser Jammers
    Replies: 5
    Last Post: 11-12-2009, 06:10 PM
  4. RX 65 Pro, blink at power cord but no power up
    By audios in forum Beltronics
    Replies: 9
    Last Post: 04-03-2009, 08:39 PM
  5. ///M Power
    By Brent_Vino in forum Car Talk
    Replies: 12
    Last Post: 03-18-2006, 09:31 AM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •