Page 2 of 3 FirstFirst 123 LastLast
Results 11 to 20 of 24

Thread: help with STI R

  1. #11
    Scratonicity Groupie
    Join Date
    Mar 2005
    Posts
    7,614

    Default Re: help with STI R

    If anything just disable laser, until you can get pick up a laser jammer.

  2. #12

    Default Re: help with STI R

    Quote Originally Posted by MPS View Post
    where is the reset ?
    To reset the STi-R and reload the factory default settings, first power off the unit. Then hold down the Vol/Mute and Sens buttons, press the power button, and then release all three buttons. The word RESET should be briefly displayed along with the firmware version number.


  3. #13
    Advanced Member
    Join Date
    Oct 2008
    Location
    Canada
    Posts
    234

    Default Re: help with STI R

    Thank you
    Bel STiR
    escort 9500ci

  4. #14
    Lead Foot
    Join Date
    Mar 2006
    Location
    At the SPA, New York
    Posts
    477

    Default Re: help with STI R

    I had the same problem with my STi-R when I first installed it. The wire to the receiver unit was too close to other electrical wires and laser went off every few minutes.

    I moved the wire to the other side of the engine bay. The 1st laser problem stopped, but whenever I used the horn it would alert to laser. I found the receiver connection wire was touching the horn wire. After I seperated them then all the laser falses stopped.


    I would assume you have some sort of electrical interference issue and would suggest you move the receiver wire to anothe location to see if that helps.

  5. #15
    Advanced Member
    Join Date
    Oct 2008
    Location
    Canada
    Posts
    234

    Default Re: help with STI R

    there is no wires near my install
    Bel STiR
    escort 9500ci

  6. #16

    Default Re: help with STI R

    Quote Originally Posted by MPS View Post
    there is no wires near my install
    Have you tested to see if you get random laser falses with the ignition turned off?

  7. #17
    Advanced Member
    Join Date
    Oct 2008
    Location
    Canada
    Posts
    234

    Default Re: help with STI R

    i only get them when i drive
    it got better today only 1 on the way to work
    Bel STiR
    escort 9500ci

  8. #18

    Default Re: help with STI R

    Quote Originally Posted by MPS View Post
    i only get them when i drive
    it got better today only 1 on the way to work
    Excellent! Now we know that the problem is:

    -- Either RF interference from wiring under the hood.
    -- Electrical noise in your car's wiring combined with either a poor ground or power connection for the STi-R.
    -- Possibly (but unlikely) a poor connection in the in-line connector along the antenna's wire harness.

    Photos at this point would help which show the antenna wiring under the hood plus where your STi-R is getting its power and ground.


  9. #19
    Advanced Member
    Join Date
    Oct 2008
    Location
    Canada
    Posts
    234

    Default Re: help with STI R

    so what ur telling me is that there is no chance its my unit ?
    pics coming soon
    Bel STiR
    escort 9500ci

  10. #20

    Default Re: help with STI R

    Quote Originally Posted by MPS View Post
    so what ur telling me is that there is no chance its my unit ?
    pics coming soon
    Yup. Its due to either electrical noise or due to poor power/ground connections. Before I went to SML 2008, one of Escort's engineers warned me about routing the 9500ci's antenna or front shifter cables close to any high voltage sources under the test car's hood since sometimes this can cause laser falses or false radar alerts.

    Since I guess you are out and about today, lets try to nip your laser false problem in the bud. Can you run by your local Radio Shack and pick up two each of the following item?

    273-105 Snap-Together Ferrite Choke Core

    These might be necessary to eliminate RF interference or noise in the power going to your STi-R.

    Yet I thought that you mentioned that you have installed additional STi-R's in your other identical vehicles? If so, then the problem is either STi-R power or ground connections, or could simply be a bad crimp job on the RJ-11 connector at the end of the antenna cable which plugs into the STi-R's interface module.


 

 

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •