blinder M27, placement help????

[mahjong007]

hi, so i finally decided to be getting a Blinder M27 with the cheetah wireless kit. so now, i been trying to decide where to place this jammer heads?

its going to be place on a 2008 honda accord ex-l, 4door. below is a enclosed picture of my vehicle, except the only difference is its metallic gray.

i was thinking to place it on the top grill (in green color) but the problem with that is, it leaves the headlights with too much open space. and the jammer heads would be too close in the middle. i think its open to more than 18inches. i cannot space it farther out than what it allows me.

my second option is to place it on the upper corners of my bumper grill ( in yellow color)?? but i am not sure if it will cover enough of the headlights or side mirror?? also, i already have a laser shield cover over the plate, dont know if that make any difference or not?

i'm not too experience with the whole laser jammer thing. i would appreciate any feedback/opinions that i can get. the more the better. i got a couple of feedback from other members, but i would like to hear more and honest opinion.

[category4]

hi, so i finally decided to be getting a Blinder M27 with the cheetah wireless kit. so now, i been trying to decide where to place this jammer heads?

its going to be place on a 2008 honda accord ex-l, 4door. below is a enclosed picture of my vehicle, except the only difference is its metallic gray.

i was thinking to place it on the top grill (in green color) but the problem with that is, it leaves the headlights with too much open space. and the jammer heads would be too close in the middle. i think its open to more than 18inches. i cannot space it farther out than what it allows me.

my second option is to place it on the upper corners of my bumper grill ( in yellow color)?? but i am not sure if it will cover enough of the headlights or side mirror?? also, i already have a laser shield cover over the plate, dont know if that make any difference or not?

i'm not too experience with the whole laser jammer thing. i would appreciate any feedback/opinions that i can get. the more the better. i got a couple of feedback from other members, but i would like to hear more and honest opinion.

In the green location would be good, just get them as widely spaced as possible.

[mahjong007]

i'm afraid that is as far to the end as it goes, because the side of the grill starts to curve up in a angle. i really dont know where to put this. i checked online, it says to have the jammer heads 20-24" from each other, and i measure that, looks like i cant even get 20 inch apart between the heads. driving me nuts.

[category4]

i'm afraid that is as far to the end as it goes, because the side of the grill starts to curve up in a angle. i really dont know where to put this. i checked online, it says to have the jammer heads 20-24" from each other, and i measure that, looks like i cant even get 20 inch apart between the heads. driving me nuts.

Having them further apart just gives you a bigger protection radius. If where you have shown will be within 18" of the headlights and license plate you should still be good.

The lower location is not bad either, but I would worry about corners of the headlights.

The only way you will know is to install then test. Luckily for you there is a great testing group there in Texas.

[mahjong007]

when u say 18inch from the headlights, do you mean 18inch from end of the jammer heads or from the center of the heads, can you make it alittle more clearer please? anyways, it is still more than 18 inch. i'm planning to use 3m moulding tape, so i hope to only have to install it once. lol

its in houston, and i cant make it that day. but hopefully i can still get it tested.

[category4]

when u say 18inch from the headlights, do you mean 18inch from end of the jammer heads or from the center of the heads, can you make it alittle more clearer please? anyways, it is still more than 18 inch. i'm planning to use 3m moulding tape, so i hope to only have to install it once. lol

its in houston, and i cant make it that day. but hopefully i can still get it tested.

They test quite often, so it should not be too hard to get them tested.

I use an 18" diameter from the center of the head. Moulding tape FTW.

[Stealth Stalker]

Green with Veil on the headlights, to shore up your wraparound headlight vulnerability. I have relative confidence in that set-up. Yellow is definitely better spacing, but no better on distance from the outer headlights, and too low for a lot of encounters.