I've been looking around for somewhere that has all the jam codes for the different guns and what they mean etc. I thought it would be a good idea to get a thread going were members could post the info on the thread and the OP keep up to date with updating the first post. If it takes off then perhaps mods could pin it for reference. Perhaps not just jam codes but weather errors such as sunlight, rain etc and any other codes that you feel should go up there. I don't mind doing it but will confess now to knowing nothing about the various guns, hence this thread.
All that is supposing I haven't missed it whilst doing a search
Just from a quick search - the codes seem to be out there just scattered about so hopefully if it sounds like a good idea I can get them all on this thread.
Kustom Prolaser III, II, I, Prolite error codes.
These guns do not have any type of JAM indicator.
Laser Atlanta SpeedLaser error codes.
JA-1, JA-2, JA-3 in HUD (indicates potential jamming)
Jammer1, Jammer2, Jammer3 on LCD (indicates that a jammer is positively detected).
Laser Atlanta has taken jammer detection a step further by identifying the "type" of jammer. Jammer detection on the Laser Atlantas is a relatively new feature. Guns produced up until July 2005 did not utilize JAM codes. Guns produced after July 2005 should have jammer type detection, and Laser Atlanta can update the software in older guns to add this feature. Reportedly, this is sometimes prone to "jam code false alerts" just like the Stalker LZ-1. We'll report on this more in the future, as soon as the jammer companies have had some time to address this new threat.
LTI error codes.
doF: Display overflow. The measurement exceeds the display capacity. Note that inscope numerical display is only four digits, while the screen display is six. It is possible to receive doF message in the scope and still have a valid measurement displaying on the screen.
eoF: Editor overflow.
Lo b: Low battery. The instrument's supply voltage level is insufficient.
E01: Measurement error - target never acquired. The target was out of range or was too close.
E02: Measurement error - insufficient data. The instruments view was obstructed or the target moved out of range.
E03: Measurement error - unstable targeting. Caused by poor aiming or by panning off the target.
E04: TOD timing error. The target was timed for less than one second.
E05: TOD time out. The target was aimed for more than 100 seconds.
E07: Jam detect - unable to acquire target.
(Along with JAM indicator on the display, and a distinct audible tone to indicate jamming). It is rare to see E07. In all of the GOL jammer tests, no jammer we have tested has ever caused this code to be displayed. The only known jammers that trigger E07 are the older Lidatek LE-10 and Target LE-850. Newer, well-established jammers currently on the market will not trigger an E07. False alerts are rare, but sometimes bright sunlight can trigger an E07..
E52: temperature too hot. Stop operation.
E53: Temperature too cold. Stop operation.
E57: Tilt sensor communication failure.
E54, E55, E56, E60, E61, E62, E63: Calibration or memory checksum failure. If the error persists, contact Laser Technology.
E70: System error - Key activated. A function key was pressed during the power up sequence. Power off, then on again.
Stalker LZ-1 error codes.
E04 = JAM
The Stalker LZ-1 has frequent "jam code false alerts", perhaps more than any other US laser gun. An E04 code is very common to see on the Stalker, even when targeting vehicles without jammers. This is possibly caused by other light sources such as sun reflections or running lights. If an officer sees E04, this isn't automatically suspicious by itself, since he probably sees it all the time.
Traffipatrol XR error codes.
E10: Missing measurement ; No target sensed or too far
E11: Incomplete measurement ; Target sometimes obscured or at limit of range
E12: Unstable measurement ; Irregular target contour or equipment wobbled
E13: Distance measuring range ; Target too close (<10m)
E14: (JAMMED) Measurement distorted ; Target has laser jamming transmitter or laser distance sensor
E21: LO BATT
E22: HI BATT (Remote supply voltage too high)
E23: LO TEMP ; < -10 deg. C
E24: HI TEMP ; > 50 deg. C
System fault codes are in the range E31 to E48
More to follow as and when I find them....




Reply With Quote

)on the issue?


Bookmarks