Results 1 to 8 of 8
  1. #1
    Old Timer
    Join Date
    Aug 2006
    Location
    Orlando, FL
    Posts
    8,880

    Default Surface is everything

    Over at the Florida Invitational, JDS applied some Veil onto my headlights for 10 bucks

    My headlights had some dried on bug splats. I tried my best to remove most of it with some Stoners Invisible Glass spray and shop towels. I was able to remove the majority of them.

    JDS applied Veil. This is what it looked like shortly after the application.


    I don't know if it can be seen, but for some odd reason the bottom half of my headlights didn't like the Veil. They seemed to "reject" it(don't know how else to say it.) It still set, but not as smoothly as the top half.

    Here's some close ups a week or two after. As many of you know, Veil sort of hazes over when it dries. It seemed to have brought out/made more visible the pits, as well as the reflector imperfections I have on my headlights.





    As far as light output at night, it didn't seem to affect my fogs/DL much. As far as the headlights, the lows have visibly been reduced, I'd say about 15-20%. The high beams were also reduced, though not as much. They just don't seem to illuminate the tree tops as much as they used to.

  2. #2
    Power User
    Join Date
    Apr 2005
    Location
    Evergreen State
    Posts
    3,884

    Default

    Bit streaky but not to bad.

    Near perfect veil application:

    http://www.pbase.com/greg_campbell/i...0/original.jpg

  3. #3
    Old Timer
    Join Date
    Aug 2006
    Location
    Orlando, FL
    Posts
    8,880

    Default

    Nice application there, holein1.

    Yea, it was a bit streaky. It was all JDS' fault j/k. As the name of the title says, it's all about the surface of the headlight. I think there might have been some bug fat or something that wasn't able to come off from the headlights, that Veil didn't like. JDS tried applying a second coat to try to cover the bottom half's "reluctantness" but I guess that further enhanced the streaking.

  4. #4
    Yoda of Radar
    Join Date
    May 2007
    Location
    Miami Beach, Florida
    Posts
    10,973

    Default

    As I said elsewhere, I think if you wetsand the headlights, the Veil would go on very nicely.

  5. #5
    Old Timer
    Join Date
    Aug 2006
    Location
    Orlando, FL
    Posts
    8,880

    Default

    Maybe that's what I should of done there. I had the stuff to do it in the car(1000 & 1500 grit paper, rubbing compound, PlasticX.) I guess I just needed the running water.

  6. #6
    Yoda of Radar
    Join Date
    May 2007
    Location
    Miami Beach, Florida
    Posts
    10,973

    Default

    I don't think I'd had my daily piss yet, you coulda asked me...


  7. #7
    Old Timer
    Join Date
    Aug 2006
    Location
    Orlando, FL
    Posts
    8,880

    Default

    Well, we did have all those gallons of water. But then again, we might have dehydrated ourselves in that heat 8)

  8. #8
    Yoda of Radar
    Join Date
    May 2007
    Location
    Miami Beach, Florida
    Posts
    10,973

    Default

    Yeah, we ended up dumping out a lot of that...

 

 

Similar Threads

  1. Replies: 6
    Last Post: 11-10-2009, 06:43 AM
  2. How far can lidar detect your speed off of a silver surface?
    By bunny in forum Radar Detectors - General
    Replies: 16
    Last Post: 10-21-2006, 05:35 PM
  3. X50 Surface Scratches
    By dreamcube in forum Escort
    Replies: 7
    Last Post: 06-29-2006, 08:09 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •