Page 3 of 4 FirstFirst 1234 LastLast
Results 21 to 30 of 38

Thread: V1 issues

  1. #21
    Good Citizen
    Join Date
    Jan 2008
    Location
    SF Bay Area, California
    Posts
    144

    Default Re: V1 issues

    Laser falsing on older V1 units can be caused by long range military radar units. I used to get this effect for miles around Edwards AFB in the California desert. Also for quite a ways along Hwy 40 in northern AZ. The effect would sometimes include areas around civilian ariports as well.

    V1 has completely eliminated this problem in newer models, so your upgrade should make a huge difference.

    Of course I'm assuming that you know that certain Infinity models use lidar ranging for their adaptive cruise control. That will set off your detector every time. Also certain high mounted brake lights (Chevy Trailblazers & others) are apparently neon units which emit frequencies in the lidar range.

    Check out the remote display in my C6:

  2. #22
    Power User
    Join Date
    Jan 2007
    Location
    South Central PA, where the Walmart has hitching posts
    Posts
    3,024

    Default Re: V1 issues

    Quote Originally Posted by carnut08 View Post

    Check out the remote display in my C6:
    Put down the camera and shift!

  3. #23
    Good Citizen
    Join Date
    Jan 2008
    Location
    SF Bay Area, California
    Posts
    144

    Default Re: V1 issues

    Quote Originally Posted by supercowpowers View Post
    Quote Originally Posted by carnut08 View Post

    Check out the remote display in my C6:
    Put down the camera and shift!
    LOL!! For sure!

    This was actually taken in my garage. The gauges swing clockwise on startup.

  4. #24
    Good Citizen
    Join Date
    Sep 2009
    Location
    Cypress, TX
    Posts
    97

    Default Re: V1 issues

    lol i was thinking the same thing. SHIFT!!!

    but yes your right it does go up like that. Where did you run your remote cord to mount it like that? It does look pretty nice!

  5. #25
    Good Citizen
    Join Date
    Sep 2009
    Location
    Cypress, TX
    Posts
    97

    Default Re: V1 issues

    ah on 40? No wonder. I was coming back from Mojabi doing the flow of traffic (20+ PSL) and it was going off like crazy. eventually just made it quiet. (it still hit me with a KA some trooper was running and saved me!!

  6. #26
    Good Citizen
    Join Date
    Jan 2008
    Location
    SF Bay Area, California
    Posts
    144

    Default Re: V1 issues

    Quote Originally Posted by Domsz06 View Post
    lol i was thinking the same thing. SHIFT!!!

    but yes your right it does go up like that. Where did you run your remote cord to mount it like that? It does look pretty nice!
    The remote is one I got off of eBay. A guy there slims them down and moves the connector to the rear. Search for "Custom THIN Valentine One 1 V1". It also comes with an additional mute switch which I mounted on the back of my turn indicator:

    The V1 unit rides on the passenger visor and is virtually invisible from outside the car:

    The power comes from a mini-fuse tap attached to the heated seats fuse location. That socket is powered when the engine runs and off when it's off. You can see it at the upper right of the photo below. It has an arrow pointing to it and the red wire goes out of the frame to the right. The other wires are for my "Mild to Wild" switch to open the pipes manually when I want to. If you're unfamiliar with that feature, it will work with your Z06 too. Note the ground at the lower left of the photo.


    As for routing the wires, the V1 power unit tucks in next to the fuse block under the carpet of the passenger footwell. I ran it under the console and above the torque tube tunnel, then around under the dash and up along the front edge of the door opening. Then I carefully pressed it into the cracks in the dash. You can't see it there. I did need to use a standard phone connector to add additional length to the factory cable due to the long path. Regular phone cord will work perfectly as long as you get a cord with all four wires inside. Many cords have only the outer two connections live and those won't work with the remote.

    This setup has worked flawlessly for over two years.

  7. #27
    Good Citizen
    Join Date
    Sep 2009
    Location
    Cypress, TX
    Posts
    97

    Default Re: V1 issues

    very nice instal!!! I do have the mild to wild. Gentelmen that did my engine and transmission work installed it for me.

    you have a very clean instal! very nice!!! question I have for you is do you think your V1 gets full signals that high up? I'd be afraid it's not getting a clean shot in the back. I keep mine just below my mirror, and when a leo is looking in from standing it can't be seen (even though if/when i get pulled over the v1 is on the floor before i'm even close to stopping, not too mention limo tint limits what he can see IMO..)

    Very nice instal!

  8. #28
    Good Citizen
    Join Date
    Jan 2008
    Location
    SF Bay Area, California
    Posts
    144

    Default Re: V1 issues

    Quote Originally Posted by Domsz06 View Post
    very nice instal!!! I do have the mild to wild. Gentelmen that did my engine and transmission work installed it for me.

    you have a very clean instal! very nice!!! question I have for you is do you think your V1 gets full signals that high up? I'd be afraid it's not getting a clean shot in the back. I keep mine just below my mirror, and when a leo is looking in from standing it can't be seen (even though if/when i get pulled over the v1 is on the floor before i'm even close to stopping, not too mention limo tint limits what he can see IMO..)

    Very nice instal!
    Thanks!

    Yes. That location gives an unobstructed 'view' both forward and to the rear. The visor is lowered slightly to the rear to make it parallel to the ground. If you scroll back up to the photo, you'll note a roll of black velcro that keeps it from snapping back up to its 'normal' position. The stock visor mount is placed with the metal clip over the front of the visor. The setup is stable and vibration free.

  9. #29
    Good Citizen
    Join Date
    Sep 2009
    Location
    Cypress, TX
    Posts
    97

    Default Re: V1 issues

    Very clean instal! I love it!

    It's too bad I didn't join this site till after moving from cali, I would have loved to come see the instal. I think I get it all, and I really think I'm going to look into doing it. Have the mirror power invisichord now, but man really like the way this looks and would be completely stealth

    Great job and thanks for the pics!

  10. #30
    Good Citizen
    Join Date
    Sep 2009
    Location
    Cypress, TX
    Posts
    97

    Default Re: V1 issues

    Have another question. What do you mean by a "switched fuse tap"? is that anything special or just where you tapped into a wire with your splice and that fuse is switched so it's hot with ignition, not when it's off?

    Thanks!

    I found the slim on ebay, think I'll start getting the parts together, but gotta find another V1 so I don't have to move it back n forth

 

 

Similar Threads

  1. V1 issues?
    By hockey005 in forum Valentine One
    Replies: 7
    Last Post: 06-16-2008, 07:28 PM
  2. Bel 955 Issues
    By DieselSpeeder in forum Beltronics
    Replies: 30
    Last Post: 05-06-2008, 07:55 PM
  3. J issues
    By TheTexan in forum Valentine One
    Replies: 12
    Last Post: 12-24-2006, 03:37 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •