Took it out and ran it against the Causeway cops. Smoking the V1 on the K band speed sign that is out there, but against three separate cruisers running KA 34.7, the V1 and STi-R were almost instantaneous on alerting. Both were giving me incredible range on detection.
I have to admit that I was thinking the STi-R would kill the V1 but it did not. I am not disappointed, though. I have the best of both worlds and think both will compliment each other should one be off its game.
STi-R plus the arrows...FTW!![]()
X2. I love how they have been parking unmanned cruisers on the crossover points lately and then blending a second cruiser in with them running C/O
.
Makes me wonder if they aren't trying to get people comfortable seeing these units with no one in them, so they can start shooting I/O in the coming weeks/months?
Nice part is that the majority of the bridge is pretty flat with the exception of a few rises and both the V1 and STi-R have no problem pcking them up. Also surprised they do not run laser more than they do?![]()
I have seen them shooting lidar every once in a while as you come off the causeway on the Mandeville side in that turn lane to the left. The cop was sitting on the trunk of his car and shooting people because you know how the speed drops to 45 as you come off the bridge.
They also park on the small left shoulder where you see reflectors and shoot lidar at around the 10 mile marker heading towards New Orleans.
I have only seen them shooting lidar once at one of the normal turn arounds.
All those empty police cars make me think that the causeway is running short on money.
Got the STi-R back from BEL, it was the EXACT same issue at last time, power supply burnt out. I guess running all my electronics on the same POSITIVE wire probably isn't a good idea, or starting the car with those units ON can cause the current on that wire to fry some of the electronics. In any event, I'm still running everything on the same Positive wire now, but in addition I wired the STi-R to the Blinder Switch, so I will NOT turn on my countermeasures until AFTER the car is started, and turn them off prior to parking. I hope this will save the precious equipment![]()
That is strange. The in-line fuse should be popping before this happens, thus preventing any surge of power to the unit.
At least you have it back.
Been running mine for two weeks now since getting it back and it is working fantastic. It is destroying my V1 on K band detection and staying ahead of it on KA hits as well.
Very pleased.![]()
That's what I figure, but it it must be allowing a certain amount of VOLTAGE through before the AMPERAGE reaches the 2AMP range for the fuse to blow, cus the fuse DOES blow, it just doesn't save the power supply BEFORE it blows.. and the techs said if I have it hardwired ALWAYS ON and not on SWITCHED voltage, when I turn the key to start the ignition, that's probably when the surge is blowing it out. Since my car doesn't have switched voltage, I just wired it to the Blinder on/off switch and will manually turn on from now on AFTER I start the vehicle.
Fuse Speed
The speed at which a fuse blows depends on how much current flows through it and the material of which the fuse is made. The operating time is not a fixed interval, but decreases as the current increases. Fuses have different characteristics of operating time compared to current, characterized as "fast-blow", "slow-blow" or "time-delay", according to time required to respond to an overcurrent condition. A standard fuse may require twice its rated current to open in one second, a fast-blow fuse may require twice its rated current to blow in 0.1 seconds, and a slow-blow fuse may require twice its rated current for tens of seconds to blow.
Fuse selection depends on the load's characteristics. Semiconductor devices may use a fast or ultrafast fuse since semiconductor devices heat rapidly when excess current flows. The fastest blowing fuses are designed for the most sensitive electrical equipment, where even a short exposure to an overload current could be very damaging. Normal fast-blow fuses are the most general purpose fuses. The time delay fuse (also known as anti-surge, or slow-blow) are designed to allow a current which is above the rated value of the fuse to flow for a short period of time without the fuse blowing. These types of fuse are used on equipment such as motors, which draw a large initial current for a few milliseconds after they have been switched on.
I'm sure you appreciate the importance of being able to separately power-cycle your Blinder and detector(s)
Bookmarks