Page 3 of 6 FirstFirst 12345 ... LastLast
Results 21 to 30 of 57

Thread: STi-R fail

  1. #21
    Good Citizen
    Join Date
    Aug 2009
    Location
    Wisconsin
    Posts
    136

    Default Re: STi-R fail

    Quote Originally Posted by Lucky225 View Post
    Quote Originally Posted by jmccam View Post
    Quote Originally Posted by Lucky225 View Post
    Got the STi-R back from BEL, it was the EXACT same issue at last time, power supply burnt out. I guess running all my electronics on the same POSITIVE wire probably isn't a good idea, or starting the car with those units ON can cause the current on that wire to fry some of the electronics. In any event, I'm still running everything on the same Positive wire now, but in addition I wired the STi-R to the Blinder Switch, so I will NOT turn on my countermeasures until AFTER the car is started, and turn them off prior to parking. I hope this will save the precious equipment

    That is strange. The in-line fuse should be popping before this happens, thus preventing any surge of power to the unit.

    At least you have it back.

    Been running mine for two weeks now since getting it back and it is working fantastic. It is destroying my V1 on K band detection and staying ahead of it on KA hits as well.

    Very pleased.
    That's what I figure, but it it must be allowing a certain amount of VOLTAGE through before the AMPERAGE reaches the 2AMP range for the fuse to blow, cus the fuse DOES blow, it just doesn't save the power supply BEFORE it blows.. and the techs said if I have it hardwired ALWAYS ON and not on SWITCHED voltage, when I turn the key to start the ignition, that's probably when the surge is blowing it out. Since my car doesn't have switched voltage, I just wired it to the Blinder on/off switch and will manually turn on from now on AFTER I start the vehicle.
    A very interesting problem. If I read this correctly, your LJ's and STIr are using the same hot wire from the power source. Is this switched power? In other words are (were) they on when the car is shut off? There are vehicles with two power recepticles (cigar lighters) one is switched one is not. If say for instance an RD were plugged into the unswitched power source it would be subjected to the starter motor draw and the alternator coming on line which would be a momentary power surge. Ok to leave the cell phone plugged into but not your RD. I find it difficult to understand why powering the RD & LJ's from the same power source would fry the STIr.

  2. #22
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by Curti View Post
    Quote Originally Posted by Lucky225 View Post
    Quote Originally Posted by jmccam View Post
    Quote Originally Posted by Lucky225 View Post
    Got the STi-R back from BEL, it was the EXACT same issue at last time, power supply burnt out. I guess running all my electronics on the same POSITIVE wire probably isn't a good idea, or starting the car with those units ON can cause the current on that wire to fry some of the electronics. In any event, I'm still running everything on the same Positive wire now, but in addition I wired the STi-R to the Blinder Switch, so I will NOT turn on my countermeasures until AFTER the car is started, and turn them off prior to parking. I hope this will save the precious equipment
    That is strange. The in-line fuse should be popping before this happens, thus preventing any surge of power to the unit.

    At least you have it back.

    Been running mine for two weeks now since getting it back and it is working fantastic. It is destroying my V1 on K band detection and staying ahead of it on KA hits as well.

    Very pleased.
    That's what I figure, but it it must be allowing a certain amount of VOLTAGE through before the AMPERAGE reaches the 2AMP range for the fuse to blow, cus the fuse DOES blow, it just doesn't save the power supply BEFORE it blows.. and the techs said if I have it hardwired ALWAYS ON and not on SWITCHED voltage, when I turn the key to start the ignition, that's probably when the surge is blowing it out. Since my car doesn't have switched voltage, I just wired it to the Blinder on/off switch and will manually turn on from now on AFTER I start the vehicle.
    A very interesting problem. If I read this correctly, your LJ's and STIr are using the same hot wire from the power source. Is this switched power? In other words are (were) they on when the car is shut off? There are vehicles with two power recepticles (cigar lighters) one is switched one is not. If say for instance an RD were plugged into the unswitched power source it would be subjected to the starter motor draw and the alternator coming on line which would be a momentary power surge. Ok to leave the cell phone plugged into but not your RD. I find it difficult to understand why powering the RD & LJ's from the same power source would fry the STIr.

    Yea, the power source for everything is on the same hot wire, and that hot wire is NOT a switched source(except that it is wired to the blinder switch), previously I had the STi-R wired in series, BEFORE the Blinder switch, so the STi-R was ALWAYS subject to the hot wire, and I would turn it on/off from the on/off on the control for the STi-R. Now, I've wired it to the Blinder Switch directly, so that you must physically flip the switch to connect the hot wire and turn the device on. The problem initially was no switched power source is available in my car(The cigar lighter in the REAR to the car is "switched", but even the it remains on for 10 minutes AFTER the car is turned off, so it's not a true switched power source, nor easy to tap into) The other problem as my ground is in the rear of the vehicle, so that's where I just put the hot wire in series with the blinder hot wire, instead of stripping it and running it all the way back to the front, which is what I've now done. Now that it's on the Blinder Switch I believe it should be fine as long as I don't flip it on prior to starting the car, and/or forget to turn it off when I park. It's much more convenient anyhow as holding the power button on the STi-R to turn it on usually takes a good 20 seconds, whereas with the flip of the blinder switch to on now takes it on, and turning blinder switch off turns it off. Much better

  3. #23
    Speed Demon
    Join Date
    Mar 2009
    Location
    State of Awareness
    Posts
    718

    Default Re: STi-R fail

    Quote Originally Posted by Lucky225 View Post
    Quote Originally Posted by Curti View Post
    Quote Originally Posted by Lucky225 View Post
    Quote Originally Posted by jmccam View Post
    Quote Originally Posted by Lucky225 View Post
    Got the STi-R back from BEL, it was the EXACT same issue at last time, power supply burnt out. I guess running all my electronics on the same POSITIVE wire probably isn't a good idea, or starting the car with those units ON can cause the current on that wire to fry some of the electronics. In any event, I'm still running everything on the same Positive wire now, but in addition I wired the STi-R to the Blinder Switch, so I will NOT turn on my countermeasures until AFTER the car is started, and turn them off prior to parking. I hope this will save the precious equipment
    That is strange. The in-line fuse should be popping before this happens, thus preventing any surge of power to the unit.

    At least you have it back.

    Been running mine for two weeks now since getting it back and it is working fantastic. It is destroying my V1 on K band detection and staying ahead of it on KA hits as well.

    Very pleased.
    That's what I figure, but it it must be allowing a certain amount of VOLTAGE through before the AMPERAGE reaches the 2AMP range for the fuse to blow, cus the fuse DOES blow, it just doesn't save the power supply BEFORE it blows.. and the techs said if I have it hardwired ALWAYS ON and not on SWITCHED voltage, when I turn the key to start the ignition, that's probably when the surge is blowing it out. Since my car doesn't have switched voltage, I just wired it to the Blinder on/off switch and will manually turn on from now on AFTER I start the vehicle.
    A very interesting problem. If I read this correctly, your LJ's and STIr are using the same hot wire from the power source. Is this switched power? In other words are (were) they on when the car is shut off? There are vehicles with two power recepticles (cigar lighters) one is switched one is not. If say for instance an RD were plugged into the unswitched power source it would be subjected to the starter motor draw and the alternator coming on line which would be a momentary power surge. Ok to leave the cell phone plugged into but not your RD. I find it difficult to understand why powering the RD & LJ's from the same power source would fry the STIr.

    Yea, the power source for everything is on the same hot wire, and that hot wire is NOT a switched source(except that it is wired to the blinder switch), previously I had the STi-R wired in series, BEFORE the Blinder switch, so the STi-R was ALWAYS subject to the hot wire, and I would turn it on/off from the on/off on the control for the STi-R. Now, I've wired it to the Blinder Switch directly, so that you must physically flip the switch to connect the hot wire and turn the device on. The problem initially was no switched power source is available in my car(The cigar lighter in the REAR to the car is "switched", but even the it remains on for 10 minutes AFTER the car is turned off, so it's not a true switched power source, nor easy to tap into) The other problem as my ground is in the rear of the vehicle, so that's where I just put the hot wire in series with the blinder hot wire, instead of stripping it and running it all the way back to the front, which is what I've now done. Now that it's on the Blinder Switch I believe it should be fine as long as I don't flip it on prior to starting the car, and/or forget to turn it off when I park. It's much more convenient anyhow as holding the power button on the STi-R to turn it on usually takes a good 20 seconds, whereas with the flip of the blinder switch to on now takes it on, and turning blinder switch off turns it off. Much better

    You have a better memory than I do, because as sure as I did that, I would either forget to turn it off or I would forget to turn it on and I would get toasted!

    I have to have my switched power to keep me honest!

  4. #24
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by jmccam View Post

    You have a better memory than I do, because as sure as I did that, I would either forget to turn it off or I would forget to turn it on and I would get toasted!

    I have to have my switched power to keep me honest!

    It'll probably still occasionally happen, but it becomes somewhat second nature(turning it on after starting the vehicle). Sorta like buckling your seat belt, something you must do before you pull out of the driveway/being to drive. I figure it'll probably be the FORGET TO TURN OFF when parking that will get me. But as long as I check the display BEFORE turning the key, I should be good.

  5. #25
    Good Citizen
    Join Date
    Aug 2009
    Location
    Wisconsin
    Posts
    136

    Default Re: STi-R fail

    What kind of a car do you have that there in no ground under the dash? Even a Corvette has suitable a ground under the dash. Does your radio go off when you shut the ignition off? That should be switched power. Tap into that on your fuse block. Auto parts stores sell a little piggy back device you can just plug in.

  6. #26
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by Curti View Post
    What kind of a car do you have that there in no ground under the dash? Even a Corvette has suitable a ground under the dash. Does your radio go off when you shut the ignition off? That should be switched power. Tap into that on your fuse block. Auto parts stores sell a little piggy back device you can just plug in.
    The fuse for the radio is in the rear, which is where I run the hot wire for the blinder, I figured the radio fuse would be switched, turns out it's not, and I never changed power source for hot, so that's why I have the ground back there. The radio does turn off when the car turns off, but it seems to use some sort of circuit that detects when the hot wire is 'hot' to turn on/off.. as the LED still blinks while the radio is off.

  7. #27
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Follow-Up..

    Maybe it's NOT the car ignition making the Power Supply fail.. I was just using the CB and noticed it was causing False K band full-strength (only for about 1/2 second, not even enough to make the detector alert a sound) on the display when I key up intermittently...

  8. #28
    Professional
    Join Date
    Jan 2010
    Location
    Your imagination
    Posts
    1,153

    Default Re: STi-R fail

    Quote Originally Posted by Lucky225 View Post
    Follow-Up..

    Maybe it's NOT the car ignition making the Power Supply fail.. I was just using the CB and noticed it was causing False K band full-strength (only for about 1/2 second, not even enough to make the detector alert a sound) on the display when I key up intermittently...
    Maybe your car has a grounding problem and its causing all the electronics to act slightly off??

  9. #29
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by Riptide View Post
    Quote Originally Posted by Lucky225 View Post
    Follow-Up..

    Maybe it's NOT the car ignition making the Power Supply fail.. I was just using the CB and noticed it was causing False K band full-strength (only for about 1/2 second, not even enough to make the detector alert a sound) on the display when I key up intermittently...
    Maybe your car has a grounding problem and its causing all the electronics to act slightly off??
    I don't think so, the ground is pretty steady and tied down with a screw to the body.. they don't like intermittently turn on/off or reset or ne thing..

  10. #30

    Default Re: STi-R fail

    Lucky you have a volt meter on the display which should show variations of power supply to the unit. It might be worth it to see if it has spiking or drain when other demands are put on the single hot wire. Set the unit highway and then go to that display and see. This feature should show variations on power. Maybe You are having a (BrownOut). Another wonderful feature that allows you to check if the power supply is being maintained.

 

 

Similar Threads

  1. V1 Fail >(
    By lilc4247 in forum Valentine One
    Replies: 55
    Last Post: 05-11-2011, 07:00 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •