Page 5 of 6 FirstFirst ... 3456 LastLast
Results 41 to 50 of 57

Thread: STi-R fail

  1. #41
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by Matt View Post
    I went back and read some of your replies.
    1-You will never get more voltage than what your battery stores. 12-14v roughly
    2-Increase Amperage to blow the fuse would indicate a short or malfunction in the STI-R
    3-The above should blow the fuse prior. As long as the fuse is sized correctly. Not to big.
    The unit should not get fried just because it is on while starting your car.
    4-Have you checked to make sure that part of the wire to the remote unit is not stripped someplace. Metal rubbing on the wire overtime could be the culprit. Even an intermitten problem.
    While this is all logical, the wire is not stripped anywhere I could find, and the unit has always fried RIGHT AFTER starting the vehicle while it was still left on..

  2. #42
    Newcomer
    Join Date
    Oct 2009
    Location
    Germany
    Posts
    10

    Default Re: STi-R fail

    Quote Originally Posted by Matt View Post
    I went back and read some of your replies.
    1-You will never get more voltage than what your battery stores. 12-14v roughly
    Unfortunately, this is simply not true.

    You have tons of more or less "inductive" loads (e.g. motors, coils etc.) in your car. Switching on and off these inductive loads at high currents will induce a very high voltage into the circuit, even so high that sparks on the switches are generated.
    "When a strongly inductive load such as an electric motor is switched off, the current cannot drop instantaneously to zero; a spark will jump across the opening contacts. Switches for inductive loads must be rated to handle these cases. The spark will cause electromagnetic interference if not suppressed; a snubber network of a resistor and capacitor in series will quell the spark."
    (taken from - in this respect quite amateurish - US-wikipedia, Switch#Inductive_loads - sorry, cannot post links)
    You can perfectly see this effect if you add a battery jumper cable or if you remove the contacts of your battery. As you might have guessed, the 13,8V of your car's battery is not sufficient to generate a spark...
    A spark is triggered when the electric field strength exceeds approximately 4–30 kV/cm
    (taken from US-wikipedia, Electrostatic_discharge#Sparks - also valid for sparks generated by induction)

  3. #43
    Good Citizen
    Join Date
    Feb 2009
    Location
    Western NY
    Posts
    190

    Default Re: STi-R fail

    You are referring to motors and capicitors. Capicitors do store voltage until drained. You are correct that you can get a very high voltage. The battery is really to help the starter, then the alternator takes over for your power. However in this application, you should not see anything higher than the 14 volts if he is on something like his radio circuit. Yes you do get a very high voltage from the plugs and coil to start the engine.
    Last edited by Matt; 04-01-2010 at 06:30 AM.

  4. #44
    Good Citizen
    Join Date
    Feb 2009
    Location
    Western NY
    Posts
    190

    Default Re: STi-R fail

    Where is MEMTEK!!! He could probably sets everyone straight. He probably already has the answer to this mystery

  5. #45
    Newcomer
    Join Date
    Oct 2009
    Location
    Germany
    Posts
    10

    Default Re: STi-R fail

    Quote Originally Posted by Matt View Post
    You are referring to motors and capicitors.
    No. It is exactly like what I have posted.

  6. #46
    Manufacturer
    Join Date
    Jun 2009
    Location
    Cincinnati, OH
    Posts
    998

    Default Re: STi-R fail

    When in doubt, read the manual. The installation manual says to connect it to switched 12V.

  7. #47
    Street Lawyer
    Join Date
    Jul 2006
    Location
    719, Colorado
    Posts
    7,108

    Default Re: STi-R fail

    Quote Originally Posted by EscortRadar View Post
    When in doubt, read the manual. The installation manual says to connect it to switched 12V.
    Thank you captain obvious, now find me a good switched 12V for a 2004 PONTIAC BONNEVILLE, and I'll be sure to do that.

  8. #48
    Professional
    Join Date
    Jan 2010
    Location
    Your imagination
    Posts
    1,153

    Default Re: STi-R fail

    Quote Originally Posted by Matt View Post
    Where is MEMTEK!!! He could probably sets everyone straight. He probably already has the answer to this mystery
    I thought he was good and disapeared

  9. #49
    Speed Demon
    Join Date
    Mar 2009
    Location
    State of Awareness
    Posts
    718

    Default Re: STi-R fail

    MEMTEK has been on hiatus for quite some time. I think he works for Escort now on how to build a better ZR4!

  10. #50
    Good Citizen
    Join Date
    Feb 2009
    Location
    Western NY
    Posts
    190

    Default Re: STi-R fail

    One could only hope

 

 

Similar Threads

  1. V1 Fail >(
    By lilc4247 in forum Valentine One
    Replies: 55
    Last Post: 05-11-2011, 07:00 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •