Just Installed LASER INTERCEPTOR DUAL

[goodtimes40]

Li before tweek front 12 12 003.JPGMe and my friend just finshed a few hours ago with a few minor tweeks on the passenger side jammer needs to be slightly more angle toward center so facing forward. And fix a ground which I just bought the part(spade) and 12g awg stranded for ground connect.
I started using the mount(aluminum had to buy extra) but after messing with it, it was clear at this time in the day(my friend has M.S. and cant go much past noon and he starts declining) and I am disabled too, but dont have ms and can function so he did electric and i did mount.
I chose 3m because I will use the other mount with zipties like i did with my m27 jammers and they worked and if the 3m on now doesnt hold and test well, I may use bracket or the mounts that came with unit-L brackets and ziptie like the blinder before. It depends on the 3m and how it holds up and keeps level and well see. Going to set up testing. Tired now and will finish up tomorrow. Please remember these pics take with a grain of salt, I added a red led to replace the blinder led hole. added a speaker and this thing is loud! and has identified all the correct laser guns from the tester I must have called 3-4 times for some help to Cliff at laserinterceptor usa and cant thank him enough for all his professional help along the way.
These pics like i said are done, but the Passenger side jammer will be moving it to face perfect forward. but today we were tired and heres the pics so far and very happy they cover the blinder m27's all the holes nicely and now have LASER INTERCEPTOR DUAL protecting me from all known gun to date and the voice module is very cool identifying all the guns. Cant wait to get friends camera to see each head firing but we tested each head covering the other head up and they are both receving the laser to each head and identifying the correct gun from tester. I will update photos tomorrow when i move the jammer on the passenger side. I was able to get the jammers level and facing forward. But the Passenger side needs to angle more toward center so the beam will be straight like the liscence plate fron holes for best possible alignment.
For the record the m27's i just replaced was because I wanted protection from new guns as well as the old ones. And I really like this size Jammer module as the blinder was just too small for me. Thanx for looking.car install 2012 laser interceptor initial install 040.JPGcar install 2012 laser interceptor initial install 036.JPGcar install 2012 laser interceptor initial install 039.JPGcar install 2012 laser interceptor initial install 043.JPG

[PMoth]

Turn the bubble level 90 Degrees so that they overhang the sensor. It is FAR more important to ensure the sensors are level in that direction. Also, great performance against 1 gun means you've done well against 1 gun. I still have unposted vids in my arsenal of vehicles jamming LTI guns all day, but then getting picked off by a Laser Atlanta at over 1200 ft...

[RadarGeek]

Turn the bubble level 90 Degrees so that they overhang the sensor. It is FAR more important to ensure the sensors are level in that direction. Also, great performance against 1 gun means you've done well against 1 gun. I still have unposted vids in my arsenal of vehicles jamming LTI guns all day, but then getting picked off by a Laser Atlanta at over 1200 ft...

What laser jammer were you using?

[PMoth]

What laser jammer were you using?

I wasn't using a jammer. I was operating the gun.

[goodtimes40]

I was using m27 until dec 22nd 2012. I currently using Li's front and going to maybe put the m27(if cant sell) in rear.
Heres a picture of level forward. This is the reason I couldnt use the aluminum mount on the Li's is because I couldnt get a level on it to check forward, etc as it runs recessed just barely where I wont be able to get a level on it at all so I went with 3m and zipties and they are straight and level. This way Im able to get the level on it. I could also use zipties and the Lbrackets the Li came with but so far the 3m is holding just fine. In any case once I get tested, I will make any changes if necc. Heres a picture of the forward level.Li before tweek front 12 12 003.JPGLi before tweek front 12 12 015.JPG
See the picture of the Li(without the level) if I use the extra alum mount, the Li would be just behind the chrome on grill and this location lets me get a level on it to check both forward and straight. I can achieve this also like I did my m27's by using the Lbrackets and zipties with no 3m. I just thought Ide try it out and so far so good.(only been a week but its holding level and straight with no issues to date from the 3m.

[PMoth]

Cool. Enjoy and Happy safe motoring.

[goodtimes40]

Right on. Thanx man. Have a safe year!